Some printing have the function name hardcoded.
It is better to use __func__ instead.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The stmmac driver use lots of pr_xxx functions to print information.
This is bad since we cannot know which device logs the information.
(moreover if two stmmac device are present)

Furthermore, it seems that it assumes wrongly that all logs will always
be subsequent by using a dev_xxx then some indented pr_xxx like this:
kernel: sun7i-dwmac 1c50000.ethernet: no reset control found
kernel:  Ring mode enabled
kernel:  No HW DMA feature register supported
kernel:  Normal descriptors
kernel:  TX Checksum insertion supported

So this patch replace all pr_xxx by their netdev_xxx counterpart.
Excepts for some printing where netdev "cause" unpretty output like:
sun7i-dwmac 1c50000.ethernet (unnamed net_device) (uninitialized): no reset control found
In those case, I keep dev_xxx.

In the same time I remove some "stmmac:" print since
this will be a duplicate with that dev_xxx displays.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling napi_hash_del() after netif_napi_del() is pointless.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need calling napi_hash_del()+synchronize_rcu() before
calling netif_napi_del()

netif_napi_del() does this already.

Using napi_hash_del() in a driver is useful only when dealing with
a batch of NAPI structures, so that a single synchronize_rcu() can
be used. mlx4_en_deactivate_cq() is deactivating a single NAPI.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add I2C access support for Mellanox ASICs:
- Virtual Protocol Interconnect switches SwitchX, SwitchX2,
  providing InfiniBand, Ethernet and Fibre Channel connectivity;
- Infiniband switches SwitchIB, SwitchIB2:
- Ethernet switch Spectrum.

Example of probing activation:
echo mlxsw_minimal 0x48 > /sys/bus/i2c/devices/i2c-2/new_device
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are going to add a minimal driver on top of the mlxsw core
infrastructure, which will be mainly used for hardware monitoring in
Baseboard management controller (BMC) installations.

Unlike the switch drivers (e.g., spectrum, switchx2), this driver does not
initialize the ASIC and therefore doesn't need to implement the init() and
fini() methods in its 'mlxsw_driver' struct.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add I2C bus implementation for Mellanox Technologies Switch ASICs.
This includes command interface implementation using input / out mailboxes,
whose location is retrieved from the firmware during probe time.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlxsw core infrastructure currently assumes that communication with
the ASIC is always possible using Ethernet management datagrams (EMADs),
but this is only possible when the PCI bus is used.

The bus capability flag is added to indicate EMAD support and make core
initialize EMAD communication only when it's set. Otherwise, register
access is done using command interface.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

knav_queue_open always returns an ERR_PTR value, never NULL.  This can be
confirmed by unfolding the function calls and conforms to the function's
documentation.  Thus, replace IS_ERR_OR_NULL by IS_ERR in error checks.

The change is made using the following semantic patch:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x;
statement S;
@@

x = knav_queue_open(...);
if (
-   IS_ERR_OR_NULL
+   IS_ERR
    (x)) S
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To display and modify the RSS hash.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The newer chips have proper support for 4-tuple UDP RSS.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some dual port NICs, the speed setting on one port can affect the
available speed on the other port.  Add logic to detect these changes
and adjust the advertised speed settings when necessary.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new FORCE_LINK_DWN bit to shutdown link during close.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New Cadence GEM hardware support Large Segment Offload (LSO):
TCP segmentation offload (TSO) as well as UDP fragmentation
offload (UFO). Support for those features was added to the driver.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netdev->real_num_rx_queues setting is only available if CONFIG_SYSFS
is enabled, so we now get a build failure when that is turned off:

netronome/nfp/nfp_net_common.c: In function 'nfp_net_ring_swap_enable':
netronome/nfp/nfp_net_common.c:2489:18: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'?

As far as I can tell, the check here is only used as an optimization that
we can skip in order to fix the compilation. If sysfs is disabled,
the following netif_set_real_num_rx_queues() has no effect.

Fixes: 164d1e9e ("nfp: add support for ethtool .set_channels")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling napi_hash_del() after netif_napi_del() is pointless.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent merge commit bb598c1b ("Merge
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net") would cause
the FIB abort warning to fire whenever we flush the FIB tables - either
during module removal or actual abort.

Move it back to its rightful location in the FIB abort function.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SPEED_UNFORCED indicates the MAC & PHY should perform
auto-negotiation to determine a speed which works. If this is called
for, don't set the force bit. If it is set, the MAC actually does
10Gbps, why the internal PHYs don't support.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GPIO support in the hardware allows for up to 16 GPIO pins, enumerated
from 0 to 15.  The driver uses the wrong value (16) to validate the GPIO
pin range in the routines to set and clear the GPIO output pins.  Update
the code to use the correct value (15).
Reported-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The debugfs support in the driver uses a common routine to write the
debugfs values. In this routine, if the input file position is non-zero
then the write routine will not return an error and an output parameter
will not have been set. Because an error isn't returned an uninitialized
value will be written into a register.

Fix the common write routine to return an error if the input file position
is non-zero, which will propagate back to the caller.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Utilize the generic phy_ethtool_nway_reset() helper function to
implement an autonegotiation restart.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch from napi_complete() to napi_complete_done()
for better GRO support (gro_flush_timeout) and core NAPI
features.

Do not rearm interrupts if we are busy polling,
to reduce bus and interrupts overhead.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not rearm interrupts if we are busy polling.

mlx4 uses separate CQ for TX and RX, so number of TX interrupts
does not change, unfortunately.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable multiple tx queues by default based on the number of online cpus. The
hardware supports up to four tx queues.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the module parameter to enable msi-x support and enable msi-x
interrupts unconditionally by default. This is a preparatory step to enable
multi queue support by default, because this is only working with msi-x
interrupts.
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares the tx path to send data on multiple tx queues. It
introduces per queue register adresses and uses them in the alx_tx_queue
structs.

There are new helper functions for the queue mapping in the tx path.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate, initialise and free alx_tx_queue structs based on the number of
alx_napi structures. Also increase the size of the descriptor memory based
on the number of tx queues in use.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the interrupt bringup code and the interrupt handler for msi-x
interrupts in order to handle multiple queues.

We must change the poll function because with multiple queues it is possible
that an alx_napi structure has only a tx or only a rx queue pointer.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the tx and rx queue structures from the alx_priv structure and switch
everything over to the queue pointers in the alx_napi structure.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new functions to allocate and free the alx_napi structures and use them
in __alx_open and __alx_stop. We only allocate one of these structures for
now, as the rest of the driver is not yet ready for multiple queues.

We switch over the setup of the interrupt mask and the call to netif_napi_add
to the new function because we must adjust these later on a per queue basis.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the driver data structures to be able to handle multiple queues.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split the allocation of descriptor memory and the buffer allocation into a
tx and rx function. This is in preparation for multiple queues where we
need to iterate over the new functions.

While at it drop the unneeded casting on the rx side.
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add trace points on the hot processing path.
Signed-off-by: NRuxandra Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export Frame Queue and Buffer Pool IDs through sysfs.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a series of counters to be exported through ethtool:
- add detailed counters for reception errors;
- add detailed counters for QMan enqueue reject events;
- count the number of fragmented skbs received from the stack;
- count all frames received on the Tx confirmation path;
- add congestion group statistics;
- count the number of interrupts for each CPU.
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for basic ethtool operations.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>