Shorten out the Attributes names.
Align all results on column 24.
Print system ID in a new line.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Some New revision 5 Attribute definitions.
Some missing definitions of Attributes and pages
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Add all constant definitions of new OSD commands added in
revision 4 & 5. Mainly for creating snapshots and clones.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Several of the doc book in the previous patches had incorrect multi-line short
function descriptors.  Fixed it all to be the correct single line descriptor.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Firmware is able to handle Broadcast primitives, but upstream driver does not
have support for broadcast primitive handling. Now this patch is mainly to
support broadcast primitives.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

FW will report Queue full event to Driver and driver will handle this queue
full event to SCSI Mid layer.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1. Handle integrated Raid device(Add/Delete) and error condition and check
   related to Raid device. is_logical_volume will represent logical volume
   device.
2. Raid device dual port support is added. Main functions to support this
   feature are mpt_raid_phys_disk_get_num_paths and mpt_raid_phys_disk_pg1.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Resending patch considering Grants G's code review.

Main goal to submit this patch is code cleaup.
1. Better driver debug prints and code indentation.
2. fault_reset_work_lock is not used anywhere. driver is using taskmgmt_lock
instead of fault_reset_work_lock.
3. setting pci_set_drvdata properly.
4. Ingore config request when IOC is in reset state.( ioc_reset_in_progress
is set).
5. Init/clear managment frame proprely.(INITIALIZE_MGMT_STATUS and
CLEAR_MGMT_STATUS)
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1.) SAS topology Rescan is added. If Firmware is doing Reset and we get
Device add interrupt from Firmware, we will not receive it as part of Reset
is going ON. After Reset we will do special Rescan of SAS topology.
2.) Driver version changed from 3.04.08 to 3.04.09.

Added proper lock/unlock in mptsas_not_responding_devices() as per James'
comment.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

SAS topology scan is restructured. HBA firmware is generating more
events. Expander Events are added, Link status events are also added with
respect to SAS topology scan optimization.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Now Firmware events are handled by firmware event queue.
Previously it was handled in interrupt context/WorkQueue of Linux.
Firmware Event handling is restructured and optimized.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1) rewrite of ioctl_cmds internal generated function that issue commands to
firmware, porting them to be single threaded using the generic MPT_MGMT
struct. All wait Queues are replace by completion Queue.
2) added seperate callback handler for ioctl task managment
(mptctl_taskmgmt_reply), to handle command that timeout
3) rewrite mptctl_bus_reset
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1.) 	Added taskmgmt_quiesce_io flag in IOC and removed resetPending from
	_MPT_SCSI_HOST struct.
2.)	Reset from Scsi mid layer and internal Reset are seperate context.
	Adding DeviceResetCtx for internal Device reset frame.
	mptsas_taskmgmt_complete is optimized as part of implementation.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1.)	 rewrite taskmanagement request and completion routines, making them
single threaded and using the generic MPT_MGMT struct, deleting
mptscsih_TMHandler, replacing with single request TM handler
mptscsih_IssueTaskMgmt, and killing the watchdog timer functions.
2.) cleanup ioc_reset callback handlers, introducing wrappers for
synchronizing error recovery (mpt_set_taskmgmt_in_progress_flag,
mpt_clear_taskmgmt_in_progress_flag), as the fusion firmware only handles
one task management request at a time
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Rewrite of all internal generated functions that issue commands to firmware,
porting them to be single threaded using the generic MPT_MGMT
struct. Implemented using completion Queue.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1) 	Previously we had mutliple #defines to use same values.
	Now those #defines are optimized.
	MPT_IOCTL_STATUS_* is removed and  MPT_MGMT_STATUS_* are new
	#defines.
2.)	config path is optimized.
	Instead of wait Queue and timer, using completion Q.
3.)	mpt_timer_expired is not used.

[jejb: elide patch to eliminate mpt_timer_expired]
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

SendEventNotification was handled through FIFO, now it is using doorbell to
communicate with hardware. Added Sleep Flag as an extra argument to support
Can-Sleep feature.  Resending patch including compilation error fix reviewed
by Grant Grundler.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

sas_discovery_quiesce_io flag is used to control IO start/resume functionality.
IO will be stoped while doing discovery of topology. Once discovery is completed
It will resume IO. Resending patch including James review.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The reason for this change is there is a data corruption when four different
physical memory regions in the 36GB to 37GB region are
accessed. This is only affecting 1078.

The solution is we need to use different addressing when filling in
the scatter gather table for the effected memory regions.  So instead
of snooping on all four different memory holes, we treat any physical
addresses in the 36GB address with the same algorithm.

The fix is explained below
1) Ensure that the message frames are NOT located in the trouble
region. There is no remapping available for message frames, they must
be allocated outside the problem region.
2) Ensure that Sense buffers are NOT in the trouble region. There is
no remapping available.
3) Walk through the SGE entries and if any are inside the trouble region
   then they need to be remapped as discussed below.
	1) Set the Local Address bit in the SGE Flags field.
  	MPI_SGE_FLAGS_LOCAL_ADDRESS
  	2) Ensure we are using 64-bit SGEs
  	3) Set MSb (Bit 63) of the 64-bit address, this will indicate buffer
	location is Host Memory.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13438
Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13437Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

New iSCSI driver for Broadcom BNX2 devices.  The driver interfaces with
the CNIC driver to access the hardware.
Signed-off-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The CNIC driver controls BNX2 hardware rings and resources used by
iSCSI.  Most hardware resources for iSCSI are separate from those
used for ethernet networking.

iSCSI uses a separate MAC address and IP address.  The CNIC driver
creates a UIO interface to handle the non-offloaded packets such as
ARP, etc in userspace.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Add interface and functions to support a new CNIC driver to drive
the Broadcom bnx2 hardware for iSCSI offload.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Add ISCSI_NETLINK messages for iSCSI NICs to get information such as
path from userspace.  Original iscsid messages are now always sent as
multicast to group 1.  The new messages are sent to group 2.

The multicast changes were made by Mike Christie.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Add support to ibmvscsi for the capabilities MAD. This command gets sent
to the Virtual I/O server prior to login in order to communicate client
capabilities. Additionally it returns information regarding capabilities
that the server supports. The two main capabilities communicated in this
MAD are related to partition migration and client reserve. Client reserve
allows for SCSI-2 reservations to be sent to virtual disks which are backed
by physical LUNs and will result in the reservation being sent to the
physical LUN.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

A new mode of error reporting, fast fail, has been added to the VIOS
which allows failover to happen more quickly.

If this new fast fail mode is enabled on the VIOS and the vSCSI client
supports the mode, the VIOS will not return MEDIUM error on path failures,
but rather return VIOSRP_ADAPTER_FAIL in the crq response, which
ibmvscsi will translate to DID_ERROR.

This new mode can be enabled for single path configurations as well,
so it is the new default error reporting mode. A module parameter is
provided to disable this new behavior on the off chance it causes a
problem on some old VIOS version.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The ibmvscsi driver currently sends the SRP Login before sending the Adapter
Info MAD, which can result in commands getting sent to the virtual adapter
before we are ready for them. This results in a slight window where the target
devices may not behave as expected. Change the order and close the window.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Previously we had one timeout that was used for all types of operations.
This adds specific timeout values for different operations (init, login,
adapter info MAD, abort task, and LUN reset).
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Adds support for 16 byte CDBs to the ibmvscsi driver.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Ensure MPS remains in synchronization across all NIC/FCoE
functions after a reset.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Queued work processing will now be serialized with its own
lower-priority spinlock.  This also simplifies the work-queue
interface for future work-queue consumers.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

As firmware will ultimately terminate (stop) and port
states-cleared.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

ISP24xx and above must query the host-status register, not HCCR.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

ISP24xx and above ISPs perform a RISC reset in
qla24xx_reset_chip(), which is called prior to
qla24xx_chip_diag().
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>