The platform has never been fully merged 
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NWim Van Sebroeck <wim@iguana.be>

This patchs uses a loongson_uart_base variable instead of the
uart_base[] array and adds a new kernel option to avoid to compile
uart_base.c all the time, which will save a little bit of memory for us.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
http://patchwork.linux-mips.org/patch/727/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Before putting the Loongson 2F into wait mode, suspend the MFGPT Timer and
after wake-up resume it.  This may save some power.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/706/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The function iodev_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/710/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: akpm@linux-foundation.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/725/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/709/

Away with the daemons of ifdef; get ready for future COP2 users.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/708/

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/683/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Yeeloong 2F netbook has an KB3310B embedded controller to manage the LID
action.  When the LID is closed or opened a SCI interrupt is sent out and
the corresponding event is saved to an EC register for later query.

Allow the LID open interrupt to wake the processor from wait mode if it is
in the suspend mode.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/685/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

YeeLoong2F has a KB3310b embedded controller. Add basic operations for
future related drivers and board support.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/684/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Several static uninitialized variables are used in the scope of __init
functions but are themselves not marked as __initdata.  This patch is to put
those variables to where they belong and to reduce the memory footprint a
little bit.

Also, a couple of lines with spaces instead of tabs were fixed.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@movial.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/698/Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

That thread "MIPS: Add option to pass return address location to
_mcount" from "David Daney <ddaney@caviumnetworks.com>" have added a new
option -mmcount-ra-address to gcc(4.5) for MIPS to transfer the location
of the return address to _mcount.

Benefit from this new feature, function graph tracer on MIPS will be
easier and safer to hijack the return address of the kernel function,
which will save some overhead and make the whole thing more reliable.

In this patch, at first, try to enable the option -mmcount-ra-address in
arch/mips/Makefile with cc-option, if gcc support it, it will be
enabled, otherwise, no side effect.

and then, we need to support this new option of gcc 4.5 and also support
the old gcc versions.

with _mcount in the old gcc versions, it's not easy to get the location
of return address(tracing: add function graph tracer support for MIPS),
   so, we do it in a C function: ftrace_get_parent_addr(ftrace.c), but
   with -mmcount-ra-address, only several instructions need to get what
   we want, so, I put into asm(mcount.S). and also, as the $12(t0) is
   used by -mmcount-ra-address for transferring the localtion of return
   address to _mcount, we need to save it into the stack and restore it
   when enabled dynamic function tracer, 'Cause we have called
   "ftrace_call" before "ftrace_graph_caller", which may destroy
   $12(t0).

(Thanks to David for providing that -mcount-ra-address and giving the
 idea of KBUILD_MCOUNT_RA_ADDRESS, both of them have made the whole
 thing more beautiful!)
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/681/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

A new option -mmcount-ra-address for gcc 4.5 have been sent by David
Daney <ddaney@caviumnetworks.com> in the thread "MIPS: Add option to
pass return address location to _mcount", which help to record the
location of the return address(ra) for the function graph tracer of MIPS
to hijack the return address easier and safer. that option used the
$12(t0) register by default, so, we reserve it for it, and use t1,t2,t3
instead of t0,t1,t2.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/680/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When remove the -fno-omit-frame-pointer, gcc will not save the frame
pointer for us, we need to save one ourselves.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/679/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch make function graph tracer work with dynamic function tracer.

To share the source code of dynamic function tracer(MCOUNT_SAVE_REGS),
and avoid restoring the whole saved registers, we need to restore the ra
register from the stack.

(NOTE: This not work with 32bit! need to ensure why!)
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/678/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The implementation of function graph tracer for MIPS is a little
different from X86.

in MIPS, gcc(with -pg) only transfer the caller's return address(at) and
the _mcount's return address(ra) to us.

For the kernel part without -mlong-calls:

move at, ra
jal _mcount

For the module part with -mlong-calls:

lui v1, hi16bit_of_mcount
addiu v1, v1, low16bit_of_mcount
move at, ra
jal _mcount

Without -mlong-calls,

if the function is a leaf, it will not save the return address(ra):

ffffffff80101298 <au1k_wait>:
ffffffff80101298:       67bdfff0        daddiu  sp,sp,-16
ffffffff8010129c:       ffbe0008        sd      s8,8(sp)
ffffffff801012a0:       03a0f02d        move    s8,sp
ffffffff801012a4:       03e0082d        move    at,ra
ffffffff801012a8:       0c042930        jal     ffffffff8010a4c0 <_mcount>
ffffffff801012ac:       00020021        nop

so, we can hijack it directly in _mcount, but if the function is non-leaf, the
return address is saved in the stack.

ffffffff80133030 <copy_process>:
ffffffff80133030:       67bdff50        daddiu  sp,sp,-176
ffffffff80133034:       ffbe00a0        sd      s8,160(sp)
ffffffff80133038:       03a0f02d        move    s8,sp
ffffffff8013303c:       ffbf00a8        sd      ra,168(sp)
ffffffff80133040:       ffb70098        sd      s7,152(sp)
ffffffff80133044:       ffb60090        sd      s6,144(sp)
ffffffff80133048:       ffb50088        sd      s5,136(sp)
ffffffff8013304c:       ffb40080        sd      s4,128(sp)
ffffffff80133050:       ffb30078        sd      s3,120(sp)
ffffffff80133054:       ffb20070        sd      s2,112(sp)
ffffffff80133058:       ffb10068        sd      s1,104(sp)
ffffffff8013305c:       ffb00060        sd      s0,96(sp)
ffffffff80133060:       03e0082d        move    at,ra
ffffffff80133064:       0c042930        jal     ffffffff8010a4c0 <_mcount>
ffffffff80133068:       00020021        nop

but we can not get the exact stack address(which saved ra) directly in
_mcount, we need to search the content of at register in the stack space
or search the "s{d,w} ra, offset(sp)" instruction in the text. 'Cause we
can not prove there is only a match in the stack space, so, we search
the text instead.

as we can see, if the first instruction above "move at, ra" is not a
store instruction, there should be a leaf function, so we hijack the at
register directly via putting &return_to_handler into it, otherwise, we
search the "s{d,w} ra, offset(sp)" instruction to get the stack offset,
and then the stack address. we use the above copy_process() as an
example, we at last find "ffbf00a8", 0xa8 is the stack offset, we plus
it with s8(fp), that is the stack address, we hijack the content via
writing the &return_to_handler in.

If with -mlong-calls, since there are two more instructions above "move
at, ra", so, we can move the pointer to the position above "lui v1,
hi16bit_of_mcount".
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/677/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch add a new section for MIPS to record the block of the hardirq
handling for function graph tracer(print_graph_irq) via adding the
__irq_entry annotation to the the entrypoints of the hardirqs(the block
with irq_enter()...irq_exit()).

Thanks goes to Steven & Frederic Weisbecker for their feedbacks.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Reviewed-by: NFrederic Weisbecker <fweisbec@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/676/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

With dynamic function tracer, by default, _mcount is defined as an
"empty" function, it returns directly without any more action . When
enabling it in user-space, it will jump to a real tracing
function(ftrace_caller), and do the real job for us.

Differ from the static function tracer, dynamic function tracer provides
two functions ftrace_make_call()/ftrace_make_nop() to enable/disable the
tracing of some indicated kernel functions(set_ftrace_filter).

In the -v4 version, the implementation of this support is basically the same as
X86 version does: _mcount is implemented as an empty function and ftrace_caller
is implemented as a real tracing function respectively.

But in this version, to support module tracing with the help of
-mlong-calls in arch/mips/Makefile:

MODFLAGS += -mlong-calls.

The stuff becomes a little more complex. We need to cope with two
different type of calling to _mcount.

For the kernel part, the calling to _mcount(result of "objdump -hdr
vmlinux"). is like this:

	108:   03e0082d        move    at,ra
	10c:   0c000000        jal     0 <fpcsr_pending>
                        10c: R_MIPS_26  _mcount
                        10c: R_MIPS_NONE        *ABS*
                        10c: R_MIPS_NONE        *ABS*
	110:   00020021        nop

For the module with -mlong-calls, it looks like this:

	c:	3c030000 	lui	v1,0x0
			c: R_MIPS_HI16	_mcount
			c: R_MIPS_NONE	*ABS*
			c: R_MIPS_NONE	*ABS*
	10:	64630000 	daddiu	v1,v1,0
			10: R_MIPS_LO16	_mcount
			10: R_MIPS_NONE	*ABS*
			10: R_MIPS_NONE	*ABS*
	14:	03e0082d 	move	at,ra
	18:	0060f809 	jalr	v1

In the kernel version, there is only one "_mcount" string for every
kernel function, so, we just need to match this one in mcount_regex of
scripts/recordmcount.pl, but in the module version, we need to choose
one of the two to match. Herein, I choose the first one with
"R_MIPS_HI16 _mcount".

and In the kernel verion, without module tracing support, we just need
to replace "jal _mcount" by "jal ftrace_caller" to do real tracing, and
filter the tracing of some kernel functions via replacing it by a nop
instruction.

but as we have described before, the instruction "jal ftrace_caller" only left
32bit length for the address of ftrace_caller, it will fail when calling from
the module space. so, herein, we must replace something else.

the basic idea is loading the address of ftrace_caller to v1 via changing these
two instructions:

	lui	v1,0x0
	addiu	v1,v1,0

If we want to enable the tracing, we need to replace the above instructions to:

	lui	v1, HI_16BIT_ftrace_caller
	addiu	v1, v1, LOW_16BIT_ftrace_caller

If we want to stop the tracing of the indicated kernel functions, we
just need to replace the "jalr v1" to a nop instruction. but we need to
replace two instructions and encode the above two instructions
oursevles.

Is there a simpler solution? Yes! Here it is, in this version, we put _mcount
and ftrace_caller together, which means the address of _mcount and
ftrace_caller is the same:

_mcount:
ftrace_caller:
	j	ftrace_stub
	 nop

	...(do real tracing here)...

ftrace_stub:
	jr	ra
	 move	ra, at

By default, the kernel functions call _mcount, and then jump to ftrace_stub and
return. and when we want to do real tracing, we just need to remove that "j
ftrace_stub", and it will run through the two "nop" instructions and then do
the real tracing job.

what about filtering job? we just need to do this:

	 lui v1, hi_16bit_of_mcount        <--> b 1f (0x10000004)
	 addiu v1, v1, low_16bit_of_mcount
	 move at, ra
	 jalr v1
	 nop
	 				     1f: (rec->ip + 12)

In linux-mips64, there will be some local symbols, whose name are
prefixed by $L, which need to be filtered. thanks goes to Steven for
writing the mips64-specific function_regex.

In a conclusion, with RISC, things becomes easier with such a "stupid"
trick, RISC is something like K.I.S.S, and also, there are lots of
"simple" tricks in the whole ftrace support, thanks goes to Steven and
the other folks for providing such a wonderful tracing framework!
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/675/Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

There is an exisiting common ftrace_test_stop_func() in
kernel/trace/ftrace.c, which is used to check the global variable
ftrace_trace_stop to determine whether stop the function tracing.

This patch implepment the MIPS specific one to speedup the procedure.

Thanks goes to Zhang Le for Cleaning it up.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/673/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

If -pg of gcc is enabled with CONFIG_FUNCTION_TRACER=y. a calling to
_mcount will be inserted into each kernel function. so, there is a
possibility to trace the kernel functions in _mcount.

This patch add the MIPS specific _mcount support for static function
tracing. by default, ftrace_trace_function is initialized as
ftrace_stub(an empty function), so, the default _mcount will introduce
very little overhead. after enabling ftrace in user-space, it will jump
to a real tracing function and do static function tracing for us.

and -ffunction-sections is incompatible with -pg, so, disable it when
ftracer is enabled.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Reviewed-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/672/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
To: LKML <linux-kernel@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Patchwork: http://patchwork.linux-mips.org/patch/661/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Loongson 2F supports CPU clock scaling. When put it into wait mode by
setting the frequency as ZERO it will stay in this mode until an external
interrupt wakes the CPU again.

To enable clock scaling support, an external timer of a known stable rate
is required.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cpufreq@vger.kernel.org,
Cc: Dave Jones <davej@redhat.com>,
Cc: Dominik Brodowski <linux@dominikbrodowski.net>,
Cc: yanh@lemote.com
Cc: huhb@lemote.com,
Patchwork: http://patchwork.linux-mips.org/patch/660/
Patchwork: http://patchwork.linux-mips.org/patch/751/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds basic options for MIPS CPUFreq support.

Since the cp0 timer's frequency is based on the processor clockrate it can
not be used with CPUFReq; an additional external timer is required.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cpufreq@vger.kernel.org,
Cc: Dave Jones <davej@redhat.com>,
Cc: Dominik Brodowski <linux@dominikbrodowski.net>,
Cc: yanh@lemote.com
Cc: huhb@lemote.com,
Patchwork: http://patchwork.linux-mips.org/patch/659/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

CPUFreq support for Loongson 2F requires an external timer.

Because the frequency of the MIPS Timer is related to the CPU frequency
which itself is variable another timer of constant frequency is required.

Export the mfgpt0 counter disable / enable operations for the coming
suspend support to suspend / resume the timer.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cpufreq@vger.kernel.org,
Cc: Dave Jones <davej@redhat.com>,
Cc: Dominik Brodowski <linux@dominikbrodowski.net>,
Cc: yanh@lemote.com
Cc: huhb@lemote.com,
Patchwork: http://patchwork.linux-mips.org/patch/658/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a new machtype and kernel options for the Lynloong.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/657/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Kernel support for this machine is almost the same as Fuloong 2F; the only
difference is that it uses the serial port provided by Loongson 2F processor
as Yeeloong 2F does.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/656/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add the Cisco Powertv cable settop box to the MIPS tree. This platform is
based on a MIPS 24Kc processor with various devices integrated on the same
ASIC. There are multiple models of this box, with differing configuration
but the same kernel runs across the product line.
Signed-off-by: NDavid VomLehn <dvomlehn@cisco.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/132/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/637/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Lemote Loongson 2F family machines need an external interrupt to wake the
system from the suspend mode.

For YeeLoong 2F and Mengloong 2F setup the keyboard interrupt as the wakeup
interrupt.

The new Fuloong 2F and LingLoong 2F have a button to directly send an
interrupt to the CPU so there is no need to setup an interrupt.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: linux-pm@lists.linux-foundation.org
Patchwork: http://patchwork.linux-mips.org/patch/630/Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch add basic suspend support for loongson2f family machines,
loongson2f have a specific feature: when we set it's frequency to ZERO,
it will go into a wait mode, and then can be waked up by the external
interrupt. so, if we setup suitable interrupts before putting it into
wait mode, we will be able wake it up whenever we want via sending the
relative interrupts to it.

These interrupts are board-specific, Yeeloong2F use the keyboard
interrupt and SCI interrupt, but LingLoong and Fuloong2F use the
interrupts connected to the processors directly. and BTW: some old
LingLoong and FuLoong2F have no such interrupts connected, so, there is
no way to wake them up from suspend mode. and therefore, please do not
enable the kernel support for them.

The board-specific support will be added in the coming patches.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: linux-pm@lists.linux-foundation.org
Patchwork: http://patchwork.linux-mips.org/patch/629/Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Loongson2f support video acceleration.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/624/
Patchwork: http://patchwork.linux-mips.org/patch/625/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds two new kernel options: CPU_SUPPORTS_CPUFREQ and
CPU_SUPPORTS_ADDRWINCFG to describe the new features of Loongons 2F and
replaces the several ugly #if clauses by them.

These two options will be utilized by the future loongson revisions and
related drivers such as the coming Loongson 2F CPUFreq driver.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add default config file for Lemote Loongson 2F family machines.  The
resulting kernel image can be shared between Fuloong 2F, Yeeloong 2F and
other Lemote Loongson 2F family machines.

If you are using an old PMON, and not using a 2f box, please add a new
command line argument in the boot.cfg.

For example, add this argument for 8.9inches notebook:

    machtype=lemote-yeeloong-2f-8.9inches

or

    machtype=8.9

More information from arch/mips/loongson/common/machtype.c.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com 
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fuloong 2F, Yeeloong 2F and Menglong 2F have different reset / shutdown
logic.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com 
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The generic i8259_irq() will make kernel hang on booting, so Loongson 2F
needs its own polling method.

IP6 is shared by the bonito interrupt and perfcounter interrupts.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com 
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

PCI support for the Fuloong 2E and Lemote Loongson 2F family machines is
mostly identical with the exception of CS5536 support.

Rename ops-fuloong2e.c to ops-loongson2.c then add the CS5536 support to
share most of the source code among Loongson machines.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com 
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Lemote Loongson 2F family machines use CS5536 as their south bridge and need
these lowlevel interfaces to access the devices on CS5536.

Virtualize the legacy devices on CS5536 as PCI devices.  This way users can
access the CS5536 PCI config space directly as a normal multi-function
PCI 2.2 device.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com 
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Currently rtclib is not available on Loongson family machines but the
legacy RTC driver works well on them.  Deselect RTC_LIB to allow the legacy
RTC driver to be selected.

The rtclib patch series

   http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=a91e34bf2595157830d599cb66becd52247b1819.1257383766.git.wuzhangjin%40gmail.com

or, in patchworks:

   http://patchwork.linux-mips.org/patch/570/
   http://patchwork.linux-mips.org/patch/571/
   http://patchwork.linux-mips.org/patch/572/

is eventually going to switch Lemote platforms to rtclib.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com 
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a new kernel option for Lemote Loongson 2F family machines.

Lemote loongson2f family machines utilize the 2f revision of loongson
processor and the AMD CS5536 south bridge.

Family members include Fuloong 2F mini PC, Yeeloong 2F notebook, LingLoong
all-in-one PC and others.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>