Remove unused fields and associated funtions-accesors.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Right now iPaq h3600's default MTD partitions table is a mess. It has
two #ifdefs with #else, giving total 3 variants, depending on your
kernel config. Replace all this with simple two-partitions scheme
(bootloader + rootfs), that used by both shipped WindowsCE and
most of the linux distributions (Familiar, Angstrom)
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There's no actual code for iPAQ sleeves support in kernel that depends
on this config option.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel

Conflicts:

	arch/arm/mach-at91/gpio.c

This patch adds basic support for Dave/DENX QongEVB-LITE i.MX31-based
board. It includes support for clocks initialization, UART1, NOR-flash,
FPGA-attached NAND flash and DNET ethernet controller (inside FPGA).
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-of-by: NJulien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Rename driver from imx-mmc to mxc-mmc to avoid conflicts with the
mx1 mmc driver.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds clkdev support for i.MX31. This is done in a
similar way done previously for i.MX27
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The UART3 had a copy-paste bug. instead of claiming rxd, txd, rts and
cts pins, cts and rts were claimed twice
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

On MX31 we can't do much without mapping the AIPS1/2 register space.
Move these mappings from individual boards to plat-mxc/mm.c
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The i.MX35 basically features the same peripherals as the i.MX31 with
some differences:

- The i.MX35 has a FEC ethernet controller
- The NAND controller base addresses are different
- The i.MX35 has only 3 UARTs
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds clock support for i.MX35 SoCs. We do not support setting
of clock rates yet, but most interesting clock rates should be reported.
I couldn't test all clock rates and the datasheet contains some obvious
bugs, so expect some bugs in this code.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

We had hardcoded cpu_is_ macros for mxc architectures till now. As we
want to run the same kernel on i.MX31 and i.MX35 this patch adds cpu_is_
macros which expand to 0 or 1 if only one architecture is compiled in and
only check for the cpu type if more than one architecture is compiled
in.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch moves the stuff common to i.MX31 and i.MX35 to mx3x.h and the
specifics to mx31.h/mx35.h. We can build a kernel which runs on i.MX31 and
i.MX35, so always include mx31.h and mx35.h
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The var->hsync_len, var->right_margin and var->left_margin fields
should contain the real values, not the hardware dependent values.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This adds the dma (ipu_dma) and fb devices for the mx31 for which drivers now are
available.

v2: merge the ipu and fb device in the same patch as suggested by Sascha
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This enables our mx31moboard to be used on the different baseboards that
we are developping according to the application needs. There are not
many differences between the boards for now, but when other peripherals
are available for mx31 the differences are going to grow.

v2: takes Sascha's comments into account
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Make sure not to create spurious pulses on GPIOs, when configuring them as
output: first set required level, then switch direction.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

include devices.h from devices.c to avoid inconsistencies and to fix
sparse warnings
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This driver has been tested on MX27/MX31. It should work on MX1/MX1
aswell, but the actual setting of the PWM is missing so far.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

v2: As pointed out by Hans J. Koch we have to claim we can do 24bit to
    make software like X work. We are lucky on i.MX that 18bit support
    has the necessary gaps in the fields to do so.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add framebuffer support for PCM038
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>