Since we are automatically managing the mutes we may as well also manage
the volume update bits, disabling volume updates while none of the inputs
are active. Since we are doing this we may as well allow the volumes to
ramp together so only enable volume updates once at the end of power up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch allows the REFCLK to be set directly allowing much greater
flexibility in how the FLLs are configured.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For optimal performance the inputs should be kept muted until after power
up. Since there are few use cases for muting inputs during capture move
the mutes to automatic control.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The generated defines in the header are pre-shifted.
Reported-by: NHeather Lomond <Heather.Lomond@wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Provide a haptics widget for use by the haptics driver and expose the DAPM
context for it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It seems WM_ADSP2("DSP1", 0) is added twice to the widgets list, remove
that and in place use ARIZONA_DSP_WIDGETS(DSP1, "DSP1").

We need to make sure that the DSP1 Aux widgets are provided otherwise
we'll see errors such as "Failed to add route DSP1 Aux 1 -> DSP1" etc.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

These are managed automatically in current revisions.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no mixer attached to the ASRC on the wm5102 only a multiplexer
to select the source for the single input line. This change correctly
defines this in the wm5102 CODEC driver.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Evalation of the WM5102 has identified a number of register values which
should be written after SYSCLK is enabled on revision A in order to
improve performance.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

ARIZONA_MICB1_ENA_SHIFT was used for micbias 2 and 3. This change
correctly uses the ARIZONA_MICBX_ENA_SHIFT for each corresponding DAPM
supply. This should not have caused any problems as the micbias enables
are in the same place in each register.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This will be used to enable additional control of the regulators.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

It will be removed from future device revisions.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some Arizona chips have a higher frequency for the FLL VCO, support this
in the common code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The analogue PGA shifts were used; this makes no practical difference as
the values are the same.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This enables common telephony use cases.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow the user to select which of the system clocks each AIF is referenced
to and constran the DAI to the set of frequencies which can be generated
from that clock.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>