Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop unused variable "poll" from cpsw_update_channels_res().
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

read_status and config_aneg are the only mandatory callbacks and most
of the time the generic implementation is used by drivers.
So make the core fall back to the generic version if a driver doesn't
implement the respective callback.

Also currently the core doesn't seem to verify that drivers implement
the mandatory calls. If a driver doesn't do so we'd just get a NPE.
With this patch this potential issue doesn't exit any longer.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

William Tu says:

====================
ip6_gre: add erspan native tunnel for ipv6

The patch series add support for ERSPAN tunnel over ipv6.  The first patch
refectors the existing ipv4 gre implementation and the second refactors the
ipv6 gre's xmit code.  Finally the last patch introduces erspan protocol.

change in v5:
  - add cover-letter description

change in v4:
  - rebase on top of net-next
  - use log_ecn_error in ip6_tnl_rcv

change in v3:
  - add inline for functions in header
  - rebase on top of net-next

change in v2:
  - remove inline
  - fix some indent
  - fix errors reports by clang and scan-build
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds support for ERSPAN tunnel over ipv6.
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refactors the ip6gre_xmit_{ipv4, ipv6}.
It is a prep work to add the ip6erspan tunnel.
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move two erspan functions to header file, erspan.h, so ipv6
erspan implementation can use it.
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Scott Branden says:

====================
net: ethtool: add support for ETH_RESET_AP

Add support to reset appplication processors inside SmartNICs by
defining new ETH_RESET_AP bit.

And use new ETH_RESET_AP bit in bnxt ethernet driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ETH_RESET_AP support handling to reset the internal
Application Processor(s) of the SmartNIC card.
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ETH_RESET_AP to reset the application processor(s) inside the NIC
interface.

Current ETH_RESET_MGMT supports a management processor inside this NIC.
This is typically used for remote NIC management purposes.

Application processors exist inside some SmartNICs to run various
applications inside the NIC processor - be it a simple algorithm without
an OS to as complex as hosting multiple VMs.
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
rds-tcp netns delete related fixes

Patchset contains cleanup and bug fixes. Patch 1 is the removal
of some redundant code/functions. Patch 2 and 3 are fixes for
corner cases identified by syzkaller. I've not been able to
reproduce the actual use-after-free race flagged in the syzkaller
reports, thus these fixes are based on code inspection plus
manual testing to make sure the modified code paths are executed
without problems in the commonly encountered timing cases.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rds_tcp_kill_sock() function parses the rds_tcp_conn_list
to find the rds_connection entries marked for deletion as part
of the netns deletion under the protection of the rds_tcp_conn_lock.
Since the rds_tcp_conn_list tracks rds_tcp_connections (which
have a 1:1 mapping with rds_conn_path), multiple tc entries in
the rds_tcp_conn_list will map to a single rds_connection, and will
be deleted as part of the rds_conn_destroy() operation that is
done outside the rds_tcp_conn_lock.

The rds_tcp_conn_list traversal done under the protection of
rds_tcp_conn_lock should not leave any doomed tc entries in
the list after the rds_tcp_conn_lock is released, else another
concurrently executiong netns delete (for a differnt netns) thread
may trip on these entries.
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8edc3aff ("rds: tcp: Take explicit refcounts on struct net")
introduces a regression in rds-tcp netns cleanup. The cleanup_net(),
(and thus rds_tcp_dev_event notification) is only called from put_net()
when all netns refcounts go to 0, but this cannot happen if the
rds_connection itself is holding a c_net ref that it expects to
release in rds_tcp_kill_sock.

Instead, the rds_tcp_kill_sock callback should make sure to
tear down state carefully, ensuring that the socket teardown
is only done after all data-structures and workqs that depend
on it are quiesced.

The original motivation for commit 8edc3aff ("rds: tcp: Take explicit
refcounts on struct net") was to resolve a race condition reported by
syzkaller where workqs for tx/rx/connect were triggered after the
namespace was deleted. Those worker threads should have been
cancelled/flushed before socket tear-down and indeed,
rds_conn_path_destroy() does try to sequence this by doing
     /* cancel cp_send_w */
     /* cancel cp_recv_w */
     /* flush cp_down_w */
     /* free data structures */
Here the "flush cp_down_w" will trigger rds_conn_shutdown and thus
invoke rds_tcp_conn_path_shutdown() to close the tcp socket, so that
we ought to have satisfied the requirement that "socket-close is
done after all other dependent state is quiesced". However,
rds_conn_shutdown has a bug in that it *always* triggers the reconnect
workq (and if connection is successful, we always restart tx/rx
workqs so with the right timing, we risk the race conditions reported
by syzkaller).

Netns deletion is like module teardown- no need to restart a
reconnect in this case. We can use the c_destroy_in_prog bit
to avoid restarting the reconnect.

Fixes: 8edc3aff ("rds: tcp: Take explicit refcounts on struct net")
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A side-effect of Commit c14b0366 ("rds: tcp: set linger to 1
when unloading a rds-tcp") is that we always send a RST on the tcp
connection for rds_conn_destroy(), so rds_tcp_conn_paths_destroy()
is not needed any more and is removed in this patch.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sending node local messages the code is using an 'mtu' of 66060
bytes to avoid unnecessary fragmentation. During situations of low
memory tipc_msg_build() may sometimes fail to allocate such large
buffers, resulting in unnecessary send failures. This can easily be
remedied by falling back to a smaller MTU, and then reassemble the
buffer chain as if the message were arriving from a remote node.

At the same time, we change the initial MTU setting of the broadcast
link to a lower value, so that large messages always are fragmented
into smaller buffers even when we run in single node mode. Apart from
obtaining the same advantage as for the 'fallback' solution above, this
turns out to give a significant performance improvement. This can
probably be explained with the __pskb_copy() operation performed on the
buffer for each recipient during reception. We found the optimal value
for this, considering the most relevant skb pool, to be 3744 bytes.
Acked-by: NYing Xue <ying.xue@ericsson.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rafal Ozieblo says:

====================
Receive packets filtering for macb driver

This patch series adds support for receive packets
filtering for Cadence GEM driver. Packets can be redirect
to different hardware queues based on source IP, destination IP,
source port or destination port. To enable filtering,
support for RX queueing was added as well.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: NRafal Ozieblo <rafalo@cadence.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added statistics per queue:
- qX_rx_packets
- qX_rx_bytes
- qX_rx_dropped
- qX_tx_packets
- qX_tx_bytes
- qX_tx_dropped
Signed-off-by: NRafal Ozieblo <rafalo@cadence.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: NRafal Ozieblo <rafalo@cadence.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several reasons for increasing the receive ring sizes:

1. The original ring size of 256 was chosen about 10 years ago when
vmxnet3 was first created. At that time, 10Gbps Ethernet was not prevalent
and servers were dominated by 1Gbps Ethernet. Now 10Gbps is common place,
and higher bandwidth links -- 25Gbps, 40Gbps, 50Gbps -- are starting
to appear. 256 Rx ring entries are simply not enough to keep up with
higher link speed when there is a burst of network frames coming from
these high speed links. Even with full MTU size frames, they are gone
in a short time. It is also more common to have a mix of frame sizes,
and more likely bi-modal distribution of frame sizes so the average frame
size is not close to full MTU. If we consider average frame size of 800B,
1024 frames that come in a burst takes ~0.65 ms to arrive at 10Gbps. With
256 entires, it takes ~0.16 ms to arrive at 10Gbps.  At 25Gbps or 40Gbps,
this time is reduced accordingly.

2. On a hypervisor where there are many VMs and CPU is over committed,
i.e. the number of VCPUs is more than the number of VCPUs, each PCPU is
in effect time shared between multiple VMs/VCPUs. The time granularity at
which this multiplexing occurs is typically coarser than between processes
on a guest OS. Trying to time slice more finely is not efficient, for
example, if memory cache is barely warmed up when switching from one VM
to another occurs. This CPU overcommit adds delay to when the driver
in a VM can service incoming packets. Whether CPU is over committed
really depends on customer workloads. For certain situations, it is very
common. For example, workloads of desktop VMs and product testing setups.
Consolidation and sharing is what drives efficiency of a customer setup
for such workloads. In these situations, the raw network bandwidth may
not be very high, but the delays between when a VM is running or not
running can also be relatively long.
Signed-off-by: NShrikrishna Khare <skhare@vmware.com>
Acked-by: NJin Heo <heoj@vmware.com>
Acked-by: NGuolin Yang <gyang@vmware.com>
Acked-by: NBoon Ang <bang@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Utilize the much more capable b53_get_tag_protocol() which takes care of
all Broadcom switches specifics to resolve which port can have Broadcom
tags enabled or not.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit e32ea7e7 ("soreuseport: fast reuseport UDP socket
selection") and commit c125e80b ("soreuseport: fast reuseport
TCP socket selection") the relevant reuseport socket matching the current
packet is selected by the reuseport_select_sock() call. The only
exceptions are invalid BPF filters/filters returning out-of-range
indices.
In the latter case the code implicitly falls back to using the hash
demultiplexing, but instead of selecting the socket inside the
reuseport_select_sock() function, it relies on the hash selection
logic introduced with the early soreuseport implementation.

With this patch, in case of a BPF filter returning a bad socket
index value, we fall back to hash-based selection inside the
reuseport_select_sock() body, so that we can drop some duplicate
code in the ipv4 and ipv6 stack.

This also allows faster lookup in the above scenario and will allow
us to avoid computing the hash value for successful, BPF based
demultiplexing - in a later patch.
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NCraig Gallek <kraig@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is not supported anymore, devices needing a MAC address
just assign one at random, it's just a driver pecularity.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Miller says:

====================
net: Significantly shrink the size of routes.

Through a combination of several things, our route structures are
larger than they need to be.

Mostly this stems from having members in dst_entry which are only used
by one class of routes.  So the majority of the work in this series is
about "un-commoning" these members and pushing them into the type
specific structures.

Unfortunately, IPSEC needed the most surgery.  The majority of the
changes here had to do with bundle creation and management.

The other issue is the refcount alignment in dst_entry.  Once we get
rid of the not-so-common members, it really opens the door to removing
that alignment entirely.

I think the new layout looks really nice, so I'll reproduce it here:

	struct net_device       *dev;
	struct  dst_ops	        *ops;
	unsigned long		_metrics;
	unsigned long           expires;
	struct xfrm_state	*xfrm;
	int			(*input)(struct sk_buff *);
	int			(*output)(struct net *net, struct sock *sk, struct sk_buff *skb);
	unsigned short		flags;
	short			obsolete;
	unsigned short		header_len;
	unsigned short		trailer_len;
	atomic_t		__refcnt;
	int			__use;
	unsigned long		lastuse;
	struct lwtunnel_state   *lwtstate;
	struct rcu_head		rcu_head;
	short			error;
	short			__pad;
	__u32			tclassid;

(This is for 64-bit, on 32-bit the __refcnt comes at the very end)

So, the good news:

1) struct dst_entry shrinks from 160 to 112 bytes.

2) struct rtable shrinks from 216 to 168 bytes.

3) struct rt6_info shrinks from 384 to 320 bytes.

Enjoy.

v2:
	Collapse some patches logically based upon feedback.
	Fix the strange patch #7.

v3:	xfrm_dst_path() needs inline keyword
	Properly align __refcnt on 32-bit.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are no more users.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

While building ipsec bundles, blocks of xfrm dsts are linked together
using dst->next from bottom to the top.

The only thing this is used for is initializing the pmtu values of the
xfrm stack, and for updating the mtu values at xfrm_bundle_ok() time.

The bundle pmtu entries must be processed in this order so that pmtu
values lower in the stack of routes can propagate up to the higher
ones.

Avoid using dst->next by simply maintaining an array of dst pointers
as we already do for the xfrm_state objects when building the bundle.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

We have padding to try and align the refcount on a separate cache
line.  But after several simplifications the padding has increased
substantially.

So now it's easy to change the layout to get rid of the padding
entirely.

We group the write-heavy __refcnt and __use with less often used
items such as the rcu_head and the error code.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

The first member of an IPSEC route bundle chain sets it's dst->path to
the underlying ipv4/ipv6 route that carries the bundle.

Stated another way, if one were to follow the xfrm_dst->child chain of
the bundle, the final non-NULL pointer would be the path and point to
either an ipv4 or an ipv6 route.

This is largely used to make sure that PMTU events propagate down to
the correct ipv4 or ipv6 route.

When we don't have the top of an IPSEC bundle 'dst->path == dst'.

Move it down into xfrm_dst and key off of dst->xfrm.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

The dst->from value is only used by ipv6 routes to track where
a route "came from".

Any time we clone or copy a core ipv6 route in the ipv6 routing
tables, we have the copy/clone's ->from point to the base route.

This is used to handle route expiration properly.

Only ipv6 uses this mechanism, and only ipv6 code references
it.  So it is safe to move it into rt6_info.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

XFRM bundle child chains look like this:

	xdst1 --> xdst2 --> xdst3 --> path_dst

All of xdstN are xfrm_dst objects and xdst->u.dst.xfrm is non-NULL.
The final child pointer in the chain, here called 'path_dst', is some
other kind of route such as an ipv4 or ipv6 one.

The xfrm output path pops routes, one at a time, via the child
pointer, until we hit one which has a dst->xfrm pointer which
is NULL.

We can easily preserve the above mechanisms with child sitting
only in the xfrm_dst structure.  All children in the chain
before we break out of the xfrm_output() loop have dst->xfrm
non-NULL and are therefore xfrm_dst objects.

Since we break out of the loop when we find dst->xfrm NULL, we
will not try to dereference 'dst' as if it were an xfrm_dst.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will make a future change moving the dst->child pointer less
invasive.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

Only IPSEC routes have a non-NULL dst->child pointer.  And IPSEC
routes are identified by a non-NULL dst->xfrm pointer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

Delete it.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>

In xmit, it is very impossible that TX_ERROR occurs. So using
unlikely optimizes the xmit process.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/atm/mpoa_* files use 'struct timeval' to store event
timestamps. struct timeval uses a 32-bit seconds field which will
overflow in the year 2038 and beyond. Morever, the timestamps are being
compared only to get seconds elapsed, so struct timeval which stores
a seconds and microseconds field is an overkill. This patch replaces
the use of struct timeval with time64_t to store a 64-bit seconds field.
Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several statements that have incorrect indentation. Fix
these.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

timespec is deprecated because of the y2038 overflow, so let's convert
this one to ktime_get_ts64(). The code is already safe even on 32-bit
architectures, since it uses monotonic times. On 64-bit architectures,
nothing changes, while on 32-bit architectures this avoids one
type conversion.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>