The BF518 has a PTP time unit that works in a similar way to other MAC
based clocks, like gianfar, ixp46x, and igb. This patch adds support for
using the blackfin as a PHC. Although the blackfin hardware does offer a
few ancillary features, this patch implements only the basic operations.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the sys time stamps and timecompare code with simple
raw hardware time stamps in nanosecond resolution. The only tricky bit is
to find a PTP Hardware Clock period slower than the input clock period
and a power of two.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware time stamping code is a compile time option for the blackfin.
When it is not enabled, the driver should fall back to the standard
ethtool reply to the get_ts_info query.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adapt adi ethernet driver to changes in bfin_get_ether_addr()
from arch/blackfin. bfin_get_ether_addr() returns now a state.
Set a random mac address via new eth_hw_addr_random() in case
the return value is not 0.

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

v2: change the logic to reduce unneeded checks
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
  - Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: NPradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well.  It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled.  This caused a dependency error.

Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the Analog Devices Inc driver into drivers/net/ethernet/adi/ and
make the necessary Kconfig and Makefile changes.

CC: <uclinux-dist-devel@blackfin.uclinux.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NBob Liu <bob.liu@analog.com>