According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.

This fixes an issue we saw with DMA transfers from SPI NOR Flashes.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add the carrier boards 3.3V supply as fixed regulator. This allows
to specify the power supply for nodes like backlight.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Drop the fake simple-bus container 'regulators' and put the
regulators directly under the root node. This also makes the
artificial 'reg' properties superfluous. While at it, remove
the unnecessary regulator-always-on property and name the
regulators according to schematics.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Assign Ethernet clock parents explicitly. The Colibri VF61
uses the 50MHz Ethernet clock provided by PLL5.

The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Assign Ethernet clock parents explicitly. The VF610 Tower Board
uses the external Ethernet clock input which is connected to
a 50MHz clock.

The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Remove the following unnecessary iomuxc container nodes:
imx6q-tbs2910
gpio_fan
gpio_leds

Sort the pinctrl nodes alphabetically.
Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Avoid the following warnings (example for usdhc2):
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state,
                               work on normal mode
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Configure SATA PHY transmit level, boost, attenuation and equalizer
parameters for long wire connections. TBS2910 contains a standard SATA
connector, so devices are typically connected with (longer) SATA cables.
And explicitly configuring these parameters avoids complaints about
"not specified" values in boot messages.
Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.

Hence each dts in the Linux kernel should provide a unique model
identifier.

Commit 8536239e ("ARM: dts: Restructure imx6qdl-wandboard.dtsi for new
rev C1 board.")' created new files imx6dl-wandboard-revb1.dts and
imx6q-wandboard-revb1.dts but used the same model identifier as in
imx6dl-wandboard.dts and imx6q-wandboard.dts.

This patch provides unique model identifiers for revision B1 of
the Wandboard Dual and Wandbaord Quad.

The patch leaves imx6dl-wandboard.dts and imx6q-wandboard.dts unchanged
because it is not foreseeable if the same dts will valid for future
board revisions or not. Furthermore we should avoid unnecessary
changes.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NPetr Štetiar <ynezz@true.cz>
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NPetr Štetiar <ynezz@true.cz>
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds dts file for imx6qp-sabresd board.
Signed-off-by: NBai Ping <ping.bai@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds basic dts file for i.MX6QP-Sbreauto board.
Signed-off-by: NBai Ping <ping.bai@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The i.MX6Quad Plus processor is an high performance SOC of i.MX6 family.
It has enhanced graphics performance and increased overall memory bandwidth
compared to i.MX6Q. Most of the design are same as i.MX6Quad/Dual, so code
for i.MX6Quad can be resued by this chip. The revision number is identied as
i.MX6Q Rev2.0, but actually it is a new chip, as we did many change to the
overall architecture.

This patch adds basic dtsi file support for the new i.MX6Quad Plus processor.
Signed-off-by: NBai Ping <ping.bai@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NDenis Carikli <denis@eukrea.com>
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.

The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vf610-twr.dts file to this combination.

CCs were acquired using (updated some email addresses, commented out
bouncing email addresses with --):
git shortlog -sne --no-merges arch/arm/boot/dts/vf610-twr.dts

--CC: Chao Fu <B44548@freescale.com>
CC: Cosmin Stoica <cosminstefan.stoica@freescale.com>
--CC: Fugang Duan <B38611@freescale.com>
--CC: Jingchang Lu <b35083@freescale.com>
--CC: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Acked-by: NBill Pringlemeir <bpringle@sympatico.ca>
Acked-by: NCory Tusar <cory.tusar@pid1solutions.com>
Acked-by: NYuan Yao <yao.yuan@freescale.com>
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.

The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vf*colibri* files to this combination.

CCs were acquired using:
git shortlog -sne --no-merges arch/arm/boot/dts/vf*colibri*
Acked-by: NCory Tusar <cory.tusar@pid1solutions.com>
Acked-by: NSanchayan Maity <maitysanchayan@gmail.com>
Acked-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.

The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vfxxx.dtsi, vf500.dtsi and vf610.dtsi files to
this combination.

CCs were acquired using (updated some email addresses, commented out
bouncing email addresses with --):
git shortlog -sne --no-merges arch/arm/boot/dts/vf???.dtsi

--CC: Chao Fu <B44548@freescale.com>
CC: Cosmin Stoica <cosminstefan.stoica@freescale.com>
CC: Frank Li <Frank.Li@freescale.com>
CC: Fugang Duan <B38611@freescale.com>
--CC: Huang Shijie <b32955@freescale.com>
--CC: Jingchang Lu <jingchang.lu@freescale.com>
--CC: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Acked-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NCory Tusar <cory.tusar@pid1solutions.com>
Acked-by: NSanchayan Maity <maitysanchayan@gmail.com>
Acked-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: NYuan Yao <yao.yuan@freescale.com>
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

LS1021a contains two PCIe controllers. The patch adds their node to
dts file.
Signed-off-by: NMinghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add sound support in UDOO board DT file.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add alias for FEC ethernet on Vybrid to allow bootloaders (like U-Boot)
patch-in the MAC address using this alias.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

PCIe reset signals are active low, and our GPIO for this is directly
connected to the PCIe reset.  However, as the PCIe driver was not using
the flag, the specification of '0' flags (which means active high) had
not been noticed.  Correct this oversight, and switch to using the
GPIO flag definitions instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Use proper gpio flag definitions for GPIOs rather than using opaque
uninformative numbers.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Avoid the following warning:

sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode

which occurs regularly at boot each time the SDHCI interface for the
Broadcom WiFi is probed at boot.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

ENET_OUT is used as reference clock for the ethernet PHY on the Ka-Ro
TX6 modules. Specify this clock in DTB to let it be managed correctly
by the driver.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds node i2c bus 3 to get the appropriate userland device
file. So for prototyping it's possible to experiment within userland.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Use pwm-backlight driver 'enable-gpios' property for backlight on/off
control.
Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The GW54xx can provide PWM4 out either the off-board backlight connector
or the off-board digital I/O connector. By default the pinmux routes it
to the backlight connector but this pinctl alternate provides documentation
for those who may want to change it.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Fix some invalid pwm pinmux configurations.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Since uboot v2016.01-rc2, which supported basic psci for i.mx7d.
So imx7d's second core can be enabled by psci.

Without arch timer, every timer event will be boardcasted to each core.
arch timer has local timer irq for each core.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.

This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.

Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>