- 05 5月, 2019 18 次提交
-
-
由 Jakub Kicinski 提交于
[ Upstream commit 97e1caa517e22d62a283b876fb8aa5f4672c83dd ] There is no guarantee the record starts before the skb frags. If we don't check for this condition copy amount will get negative, leading to reads and writes to random memory locations. Familiar hilarity ensues. Fixes: 4799ac81 ("tls: Add rx inline crypto offload") Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: NJohn Hurley <john.hurley@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Michael Chan 提交于
[ Upstream commit 0b397b17a4120cb80f7bf89eb30587b3dd9b0d1d ] In bnxt_rx_pkt(), if the driver encounters BD errors, it will recycle the buffers and jump to the end where the uninitailized variable "len" is referenced. Fix it by adding a new jump label that will skip the length update. This is the most correct fix since the length may not be valid when we get this type of error. Fixes: 6a8788f2 ("bnxt_en: add support for software dynamic interrupt moderation") Reported-by: NNathan Chancellor <natechancellor@gmail.com> Cc: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Reviewed-by: NNathan Chancellor <natechancellor@gmail.com> Tested-by: NNathan Chancellor <natechancellor@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Vasundhara Volam 提交于
[ Upstream commit f9099d611449836a51a65f40ea7dc9cb5f2f665e ] In the bnxt_init_one() error path, short FW command request memory is not freed. This patch fixes it. Fixes: e605db80 ("bnxt_en: Support for Short Firmware Message") Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Michael Chan 提交于
[ Upstream commit b4e30e8e7ea1d1e35ffd64ca46f7d9a7f227b4bf ] The driver builds a list of multicast addresses and sends it to the firmware when the driver's ndo_set_rx_mode() is called. In rare cases, the firmware can fail this call if internal resources to add multicast addresses are exhausted. In that case, we should try the call again by setting the ALL_MCAST flag which is more guaranteed to succeed. Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Willem de Bruijn 提交于
[ Upstream commit 486efdc8f6ce802b27e15921d2353cc740c55451 ] Packet sockets in datagram mode take a destination address. Verify its length before passing to dev_hard_header. Prior to 2.6.14-rc3, the send code ignored sll_halen. This is established behavior. Directly compare msg_namelen to dev->addr_len. Change v1->v2: initialize addr in all paths Fixes: 6b8d95f1795c4 ("packet: validate address length if non-zero") Suggested-by: NDavid Laight <David.Laight@aculab.com> Signed-off-by: NWillem de Bruijn <willemb@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Hangbin Liu 提交于
[ Upstream commit f68d7c44e76532e46f292ad941aa3706cb9e6e40 ] Fixes: 65b2b493 ("selftests: net: initial fib rule tests") Signed-off-by: NHangbin Liu <liuhangbin@gmail.com> Reviewed-by: NDavid Ahern <dsahern@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Xin Long 提交于
[ Upstream commit fbd019737d71e405f86549fd738f81e2ff3dd073 ] Ying triggered a call trace when doing an asconf testing: BUG: scheduling while atomic: swapper/12/0/0x10000100 Call Trace: <IRQ> [<ffffffffa4375904>] dump_stack+0x19/0x1b [<ffffffffa436fcaf>] __schedule_bug+0x64/0x72 [<ffffffffa437b93a>] __schedule+0x9ba/0xa00 [<ffffffffa3cd5326>] __cond_resched+0x26/0x30 [<ffffffffa437bc4a>] _cond_resched+0x3a/0x50 [<ffffffffa3e22be8>] kmem_cache_alloc_node+0x38/0x200 [<ffffffffa423512d>] __alloc_skb+0x5d/0x2d0 [<ffffffffc0995320>] sctp_packet_transmit+0x610/0xa20 [sctp] [<ffffffffc098510e>] sctp_outq_flush+0x2ce/0xc00 [sctp] [<ffffffffc098646c>] sctp_outq_uncork+0x1c/0x20 [sctp] [<ffffffffc0977338>] sctp_cmd_interpreter.isra.22+0xc8/0x1460 [sctp] [<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp] [<ffffffffc099443d>] sctp_primitive_ASCONF+0x3d/0x50 [sctp] [<ffffffffc0977384>] sctp_cmd_interpreter.isra.22+0x114/0x1460 [sctp] [<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp] [<ffffffffc097b3a4>] sctp_assoc_bh_rcv+0xf4/0x1b0 [sctp] [<ffffffffc09840f1>] sctp_inq_push+0x51/0x70 [sctp] [<ffffffffc099732b>] sctp_rcv+0xa8b/0xbd0 [sctp] As it shows, the first sctp_do_sm() running under atomic context (NET_RX softirq) invoked sctp_primitive_ASCONF() that uses GFP_KERNEL flag later, and this flag is supposed to be used in non-atomic context only. Besides, sctp_do_sm() was called recursively, which is not expected. Vlad tried to fix this recursive call in Commit c0786693 ("sctp: Fix oops when sending queued ASCONF chunks") by introducing a new command SCTP_CMD_SEND_NEXT_ASCONF. But it didn't work as this command is still used in the first sctp_do_sm() call, and sctp_primitive_ASCONF() will be called in this command again. To avoid calling sctp_do_sm() recursively, we send the next queued ASCONF not by sctp_primitive_ASCONF(), but by sctp_sf_do_prm_asconf() in the 1st sctp_do_sm() directly. Reported-by: NYing Xu <yinxu@redhat.com> Signed-off-by: NXin Long <lucien.xin@gmail.com> Acked-by: NNeil Horman <nhorman@tuxdriver.com> Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 David Howells 提交于
[ Upstream commit b13023421b5179413421333f602850914f6a7ad8 ] In rxrpc_destroy_all_calls(), there are two phases: (1) make sure the ->calls list is empty, emitting error messages if not, and (2) wait for the RCU cleanup to happen on outstanding calls (ie. ->nr_calls becomes 0). To avoid taking the call_lock, the function prechecks ->calls and if empty, it returns to avoid taking the lock - this is wrong, however: it still needs to go and do the second phase and wait for ->nr_calls to become 0. Without this, the rxrpc_net struct may get deallocated before we get to the RCU cleanup for the last calls. This can lead to: Slab corruption (Not tainted): kmalloc-16k start=ffff88802b178000, len=16384 050: 6b 6b 6b 6b 6b 6b 6b 6b 61 6b 6b 6b 6b 6b 6b 6b kkkkkkkkakkkkkkk Note the "61" at offset 0x58. This corresponds to the ->nr_calls member of struct rxrpc_net (which is >9k in size, and thus allocated out of the 16k slab). Fix this by flipping the condition on the if-statement, putting the locked section inside the if-body and dropping the return from there. The function will then always go on to wait for the RCU cleanup on outstanding calls. Fixes: 2baec2c3 ("rxrpc: Support network namespacing") Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Jakub Kicinski 提交于
[ Upstream commit 2dcb003314032c6efb13a065ffae60d164b2dd35 ] update_chksum() accesses nskb->sk before it has been set by complete_skb(), move the init up. Fixes: e8f69799 ("net/tls: Add generic NIC offload infrastructure") Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: NSimon Horman <simon.horman@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Andrew Lunn 提交于
[ Upstream commit fdfdf86720a34527f777cbe0d8599bf0528fa146 ] marvell_get_sset_count() returns how many statistics counters there are. If the PHY supports fibre, there are 3, otherwise two. marvell_get_strings() does not make this distinction, and always returns 3 strings. This then often results in writing past the end of the buffer for the strings. Fixes: 2170fef7 ("Marvell phy: add field to get errors from fiber link.") Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Dan Carpenter 提交于
[ Upstream commit f949a12fd697479f68d99dc65e9bbab68ee49043 ] The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc(). We can't pass unclamped values to test_bit() or it results in an out of bounds access beyond the end of the bitmap. Fixes: 7318166c ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Eric Dumazet 提交于
[ Upstream commit c1c477217882c610a2ba0268f5faf36c9c092528 ] Canonical way to fetch sk_user_data from an encap_rcv() handler called from UDP stack in rcu protected section is to use rcu_dereference_sk_user_data(), otherwise compiler might read it multiple times. Fixes: d00fa9ad ("il2tp: fix races with tunnel socket close") Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: James Chapman <jchapman@katalix.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Eric Dumazet 提交于
[ Upstream commit a622b40035d16196bf19b2b33b854862595245fc ] Before taking a refcount on a rcu protected structure, we need to make sure the refcount is not zero. syzbot reported : refcount_t: increment on 0; use-after-free. WARNING: CPU: 1 PID: 23533 at lib/refcount.c:156 refcount_inc_checked lib/refcount.c:156 [inline] WARNING: CPU: 1 PID: 23533 at lib/refcount.c:156 refcount_inc_checked+0x61/0x70 lib/refcount.c:154 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 23533 Comm: syz-executor.2 Not tainted 5.1.0-rc7+ #93 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 panic+0x2cb/0x65c kernel/panic.c:214 __warn.cold+0x20/0x45 kernel/panic.c:571 report_bug+0x263/0x2b0 lib/bug.c:186 fixup_bug arch/x86/kernel/traps.c:179 [inline] fixup_bug arch/x86/kernel/traps.c:174 [inline] do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:272 do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:291 invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:973 RIP: 0010:refcount_inc_checked lib/refcount.c:156 [inline] RIP: 0010:refcount_inc_checked+0x61/0x70 lib/refcount.c:154 Code: 1d 98 2b 2a 06 31 ff 89 de e8 db 2c 40 fe 84 db 75 dd e8 92 2b 40 fe 48 c7 c7 20 7a a1 87 c6 05 78 2b 2a 06 01 e8 7d d9 12 fe <0f> 0b eb c1 90 90 90 90 90 90 90 90 90 90 90 55 48 89 e5 41 57 41 RSP: 0018:ffff888069f0fba8 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 000000000000f353 RSI: ffffffff815afcb6 RDI: ffffed100d3e1f67 RBP: ffff888069f0fbb8 R08: ffff88809b1845c0 R09: ffffed1015d23ef1 R10: ffffed1015d23ef0 R11: ffff8880ae91f787 R12: ffff8880a8f26968 R13: 0000000000000004 R14: dffffc0000000000 R15: ffff8880a49a6440 l2tp_tunnel_inc_refcount net/l2tp/l2tp_core.h:240 [inline] l2tp_tunnel_get+0x250/0x580 net/l2tp/l2tp_core.c:173 pppol2tp_connect+0xc00/0x1c70 net/l2tp/l2tp_ppp.c:702 __sys_connect+0x266/0x330 net/socket.c:1808 __do_sys_connect net/socket.c:1819 [inline] __se_sys_connect net/socket.c:1816 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1816 Fixes: 54652eb1 ("l2tp: hold tunnel while looking up sessions in l2tp_netlink") Signed-off-by: NEric Dumazet <edumazet@google.com> Reported-by: Nsyzbot <syzkaller@googlegroups.com> Cc: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Willem de Bruijn 提交于
[ Upstream commit 95c169251bf734aa555a1e8043e4d88ec97a04ec ] A request for a flowlabel fails in process or user exclusive mode must fail if the caller pid or uid does not match. Invert the test. Previously, the test was unsafe wrt PID recycling, but indeed tested for inequality: fl1->owner != fl->owner Fixes: 4f82f457 ("net ip6 flowlabel: Make owner a union of struct pid* and kuid_t") Signed-off-by: NWillem de Bruijn <willemb@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Eric Dumazet 提交于
[ Upstream commit 6c0afef5fb0c27758f4d52b2210c61b6bd8b4470 ] syzbot was able to catch a use-after-free read in pid_nr_ns() [1] ip6fl_seq_show() seems to use RCU protection, dereferencing fl->owner.pid but fl_free() releases fl->owner.pid before rcu grace period is started. [1] BUG: KASAN: use-after-free in pid_nr_ns+0x128/0x140 kernel/pid.c:407 Read of size 4 at addr ffff888094012a04 by task syz-executor.0/18087 CPU: 0 PID: 18087 Comm: syz-executor.0 Not tainted 5.1.0-rc6+ #89 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 __asan_report_load4_noabort+0x14/0x20 mm/kasan/generic_report.c:131 pid_nr_ns+0x128/0x140 kernel/pid.c:407 ip6fl_seq_show+0x2f8/0x4f0 net/ipv6/ip6_flowlabel.c:794 seq_read+0xad3/0x1130 fs/seq_file.c:268 proc_reg_read+0x1fe/0x2c0 fs/proc/inode.c:227 do_loop_readv_writev fs/read_write.c:701 [inline] do_loop_readv_writev fs/read_write.c:688 [inline] do_iter_read+0x4a9/0x660 fs/read_write.c:922 vfs_readv+0xf0/0x160 fs/read_write.c:984 kernel_readv fs/splice.c:358 [inline] default_file_splice_read+0x475/0x890 fs/splice.c:413 do_splice_to+0x12a/0x190 fs/splice.c:876 splice_direct_to_actor+0x2d2/0x970 fs/splice.c:953 do_splice_direct+0x1da/0x2a0 fs/splice.c:1062 do_sendfile+0x597/0xd00 fs/read_write.c:1443 __do_sys_sendfile64 fs/read_write.c:1498 [inline] __se_sys_sendfile64 fs/read_write.c:1490 [inline] __x64_sys_sendfile64+0x15a/0x220 fs/read_write.c:1490 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x458da9 Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f300d24bc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028 RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 0000000000458da9 RDX: 00000000200000c0 RSI: 0000000000000008 RDI: 0000000000000007 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 000000000000005a R11: 0000000000000246 R12: 00007f300d24c6d4 R13: 00000000004c5fa3 R14: 00000000004da748 R15: 00000000ffffffff Allocated by task 17543: save_stack+0x45/0xd0 mm/kasan/common.c:75 set_track mm/kasan/common.c:87 [inline] __kasan_kmalloc mm/kasan/common.c:497 [inline] __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:470 kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:505 slab_post_alloc_hook mm/slab.h:437 [inline] slab_alloc mm/slab.c:3393 [inline] kmem_cache_alloc+0x11a/0x6f0 mm/slab.c:3555 alloc_pid+0x55/0x8f0 kernel/pid.c:168 copy_process.part.0+0x3b08/0x7980 kernel/fork.c:1932 copy_process kernel/fork.c:1709 [inline] _do_fork+0x257/0xfd0 kernel/fork.c:2226 __do_sys_clone kernel/fork.c:2333 [inline] __se_sys_clone kernel/fork.c:2327 [inline] __x64_sys_clone+0xbf/0x150 kernel/fork.c:2327 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 7789: save_stack+0x45/0xd0 mm/kasan/common.c:75 set_track mm/kasan/common.c:87 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/common.c:459 kasan_slab_free+0xe/0x10 mm/kasan/common.c:467 __cache_free mm/slab.c:3499 [inline] kmem_cache_free+0x86/0x260 mm/slab.c:3765 put_pid.part.0+0x111/0x150 kernel/pid.c:111 put_pid+0x20/0x30 kernel/pid.c:105 fl_free+0xbe/0xe0 net/ipv6/ip6_flowlabel.c:102 ip6_fl_gc+0x295/0x3e0 net/ipv6/ip6_flowlabel.c:152 call_timer_fn+0x190/0x720 kernel/time/timer.c:1325 expire_timers kernel/time/timer.c:1362 [inline] __run_timers kernel/time/timer.c:1681 [inline] __run_timers kernel/time/timer.c:1649 [inline] run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694 __do_softirq+0x266/0x95a kernel/softirq.c:293 The buggy address belongs to the object at ffff888094012a00 which belongs to the cache pid_2 of size 88 The buggy address is located 4 bytes inside of 88-byte region [ffff888094012a00, ffff888094012a58) The buggy address belongs to the page: page:ffffea0002500480 count:1 mapcount:0 mapping:ffff88809a483080 index:0xffff888094012980 flags: 0x1fffc0000000200(slab) raw: 01fffc0000000200 ffffea00018a3508 ffffea0002524a88 ffff88809a483080 raw: ffff888094012980 ffff888094012000 000000010000001b 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888094012900: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc ffff888094012980: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc >ffff888094012a00: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc ^ ffff888094012a80: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc ffff888094012b00: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc Fixes: 4f82f457 ("net ip6 flowlabel: Make owner a union of struct pid * and kuid_t") Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Reported-by: Nsyzbot <syzkaller@googlegroups.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Eric Dumazet 提交于
[ Upstream commit 0e2338749192ce0e52e7174c5352f627632f478a ] We had many syzbot reports that seem to be caused by use-after-free of struct fib6_info. ip6_dst_destroy(), fib6_drop_pcpu_from() and rt6_remove_exception() are writers vs rt->from, and use non consistent synchronization among themselves. Switching to xchg() will solve the issues with no possible lockdep issues. BUG: KASAN: user-memory-access in atomic_dec_and_test include/asm-generic/atomic-instrumented.h:747 [inline] BUG: KASAN: user-memory-access in fib6_info_release include/net/ip6_fib.h:294 [inline] BUG: KASAN: user-memory-access in fib6_info_release include/net/ip6_fib.h:292 [inline] BUG: KASAN: user-memory-access in fib6_drop_pcpu_from net/ipv6/ip6_fib.c:927 [inline] BUG: KASAN: user-memory-access in fib6_purge_rt+0x4f6/0x670 net/ipv6/ip6_fib.c:960 Write of size 4 at addr 0000000000ffffb4 by task syz-executor.1/7649 CPU: 0 PID: 7649 Comm: syz-executor.1 Not tainted 5.1.0-rc6+ #183 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 kasan_report.cold+0x5/0x40 mm/kasan/report.c:321 check_memory_region_inline mm/kasan/generic.c:185 [inline] check_memory_region+0x123/0x190 mm/kasan/generic.c:191 kasan_check_write+0x14/0x20 mm/kasan/common.c:108 atomic_dec_and_test include/asm-generic/atomic-instrumented.h:747 [inline] fib6_info_release include/net/ip6_fib.h:294 [inline] fib6_info_release include/net/ip6_fib.h:292 [inline] fib6_drop_pcpu_from net/ipv6/ip6_fib.c:927 [inline] fib6_purge_rt+0x4f6/0x670 net/ipv6/ip6_fib.c:960 fib6_del_route net/ipv6/ip6_fib.c:1813 [inline] fib6_del+0xac2/0x10a0 net/ipv6/ip6_fib.c:1844 fib6_clean_node+0x3a8/0x590 net/ipv6/ip6_fib.c:2006 fib6_walk_continue+0x495/0x900 net/ipv6/ip6_fib.c:1928 fib6_walk+0x9d/0x100 net/ipv6/ip6_fib.c:1976 fib6_clean_tree+0xe0/0x120 net/ipv6/ip6_fib.c:2055 __fib6_clean_all+0x118/0x2a0 net/ipv6/ip6_fib.c:2071 fib6_clean_all+0x2b/0x40 net/ipv6/ip6_fib.c:2082 rt6_sync_down_dev+0x134/0x150 net/ipv6/route.c:4057 rt6_disable_ip+0x27/0x5f0 net/ipv6/route.c:4062 addrconf_ifdown+0xa2/0x1220 net/ipv6/addrconf.c:3705 addrconf_notify+0x19a/0x2260 net/ipv6/addrconf.c:3630 notifier_call_chain+0xc7/0x240 kernel/notifier.c:93 __raw_notifier_call_chain kernel/notifier.c:394 [inline] raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1753 call_netdevice_notifiers_extack net/core/dev.c:1765 [inline] call_netdevice_notifiers net/core/dev.c:1779 [inline] dev_close_many+0x33f/0x6f0 net/core/dev.c:1522 rollback_registered_many+0x43b/0xfd0 net/core/dev.c:8177 rollback_registered+0x109/0x1d0 net/core/dev.c:8242 unregister_netdevice_queue net/core/dev.c:9289 [inline] unregister_netdevice_queue+0x1ee/0x2c0 net/core/dev.c:9282 unregister_netdevice include/linux/netdevice.h:2658 [inline] __tun_detach+0xd5b/0x1000 drivers/net/tun.c:727 tun_detach drivers/net/tun.c:744 [inline] tun_chr_close+0xe0/0x180 drivers/net/tun.c:3443 __fput+0x2e5/0x8d0 fs/file_table.c:278 ____fput+0x16/0x20 fs/file_table.c:309 task_work_run+0x14a/0x1c0 kernel/task_work.c:113 exit_task_work include/linux/task_work.h:22 [inline] do_exit+0x90a/0x2fa0 kernel/exit.c:876 do_group_exit+0x135/0x370 kernel/exit.c:980 __do_sys_exit_group kernel/exit.c:991 [inline] __se_sys_exit_group kernel/exit.c:989 [inline] __x64_sys_exit_group+0x44/0x50 kernel/exit.c:989 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x458da9 Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffeafc2a6a8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 RAX: ffffffffffffffda RBX: 000000000000001c RCX: 0000000000458da9 RDX: 0000000000412a80 RSI: 0000000000a54ef0 RDI: 0000000000000043 RBP: 00000000004be552 R08: 000000000000000c R09: 000000000004c0d1 R10: 0000000002341940 R11: 0000000000000246 R12: 00000000ffffffff R13: 00007ffeafc2a7f0 R14: 000000000004c065 R15: 00007ffeafc2a800 Fixes: a68886a6 ("net/ipv6: Make from in rt6_info rcu protected") Signed-off-by: NEric Dumazet <edumazet@google.com> Reported-by: Nsyzbot <syzkaller@googlegroups.com> Cc: David Ahern <dsahern@gmail.com> Reviewed-by: NDavid Ahern <dsahern@gmail.com> Acked-by: NMartin KaFai Lau <kafai@fb.com> Acked-by: NWei Wang <weiwan@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Martin KaFai Lau 提交于
[ Upstream commit 886b7a50100a50f1cbd08a6f8ec5884dfbe082dc ] It is a followup after the fix in commit 9c69a1320515 ("route: Avoid crash from dereferencing NULL rt->from") rt6_do_redirect(): 1. NULL checking is needed on rt->from because a parallel fib6_info delete could happen that sets rt->from to NULL. (e.g. rt6_remove_exception() and fib6_drop_pcpu_from()). 2. fib6_info_hold() is not enough. Same reason as (1). Meaning, holding dst->__refcnt cannot ensure rt->from is not NULL or rt->from->fib6_ref is not 0. Instead of using fib6_info_hold_safe() which ip6_rt_cache_alloc() is already doing, this patch chooses to extend the rcu section to keep "from" dereference-able after checking for NULL. inet6_rtm_getroute(): 1. NULL checking is also needed on rt->from for a similar reason. Note that inet6_rtm_getroute() is using RTNL_FLAG_DOIT_UNLOCKED. Fixes: a68886a6 ("net/ipv6: Make from in rt6_info rcu protected") Signed-off-by: NMartin KaFai Lau <kafai@fb.com> Acked-by: NWei Wang <weiwan@google.com> Reviewed-by: NDavid Ahern <dsahern@gmail.com> Reviewed-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Shmulik Ladkani 提交于
[ Upstream commit d2f0c961148f65bc73eda72b9fa3a4e80973cb49 ] Previously, during fragmentation after forwarding, skb->skb_iif isn't preserved, i.e. 'ip_copy_metadata' does not copy skb_iif from given 'from' skb. As a result, ip_do_fragment's creates fragments with zero skb_iif, leading to inconsistent behavior. Assume for example an eBPF program attached at tc egress (post forwarding) that examines __sk_buff->ingress_ifindex: - the correct iif is observed if forwarding path does not involve fragmentation/refragmentation - a bogus iif is observed if forwarding path involves fragmentation/refragmentatiom Fix, by preserving skb_iif during 'ip_copy_metadata'. Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 04 5月, 2019 22 次提交
-
-
由 Greg Kroah-Hartman 提交于
-
由 Rasmus Villemoes 提交于
[ Upstream commit 909346433064b8d840dc82af26161926b8d37558 ] If userspace doesn't end the input with a newline (which can easily happen if the write happens from a C program that does write(fd, iface, strlen(iface))), we may end up including garbage from a previous, longer value in the device_name. For example # cat device_name # printf 'eth12' > device_name # cat device_name eth12 # printf 'eth3' > device_name # cat device_name eth32 I highly doubt anybody is relying on this behaviour, so switch to simply copying the bytes (we've already checked that size is < IFNAMSIZ) and unconditionally zero-terminate it; of course, we also still have to strip a trailing newline. This is also preparation for future patches. Fixes: 06f502f5 ("leds: trigger: Introduce a NETDEV trigger") Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: NPavel Machek <pavel@ucw.cz> Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Kangjie Lu 提交于
[ Upstream commit 0aab8e4df4702b31314a27ec4b0631dfad0fae0a ] In case of_match_device cannot find a match, return -EINVAL to avoid NULL pointer dereference. Fixes: fa4191a6 ("leds: pca9532: Add device tree support") Signed-off-by: NKangjie Lu <kjlu@umn.edu> Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Andrei Vagin 提交于
[ Upstream commit fcfc2aa0185f4a731d05a21e9f359968fdfd02e7 ] There are a few system calls (pselect, ppoll, etc) which replace a task sigmask while they are running in a kernel-space When a task calls one of these syscalls, the kernel saves a current sigmask in task->saved_sigmask and sets a syscall sigmask. On syscall-exit-stop, ptrace traps a task before restoring the saved_sigmask, so PTRACE_GETSIGMASK returns the syscall sigmask and PTRACE_SETSIGMASK does nothing, because its sigmask is replaced by saved_sigmask, when the task returns to user-space. This patch fixes this problem. PTRACE_GETSIGMASK returns saved_sigmask if it's set. PTRACE_SETSIGMASK drops the TIF_RESTORE_SIGMASK flag. Link: http://lkml.kernel.org/r/20181120060616.6043-1-avagin@gmail.com Fixes: 29000cae ("ptrace: add ability to get/set signal-blocked mask") Signed-off-by: NAndrei Vagin <avagin@gmail.com> Acked-by: NOleg Nesterov <oleg@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Joerg Roedel 提交于
[ Upstream commit 8aafaaf2212192012f5bae305bb31cdf7681d777 ] If a device has an exclusion range specified in the IVRS table, this region needs to be reserved in the iova-domain of that device. This hasn't happened until now and can cause data corruption on data transfered with these devices. Treat exclusion ranges as reserved regions in the iommu-core to fix the problem. Fixes: be2a022c ('x86, AMD IOMMU: add functions to parse IOMMU memory mapping requirements for devices') Signed-off-by: NJoerg Roedel <jroedel@suse.de> Reviewed-by: NGary R Hook <gary.hook@amd.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Changbin Du 提交于
[ Upstream commit 9c38f1f044080392603c497ecca4d7d09876ff99 ] Backspace is not working on some terminal emulators which do not send the key code defined by terminfo. Terminals either send '^H' (8) or '^?' (127). But currently only '^?' is handled. Let's also handle '^H' for those terminals. Signed-off-by: NChangbin Du <changbin.du@gmail.com> Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Wei Li 提交于
[ Upstream commit 977c7a6d1e263ff1d755f28595b99e4bc0c48a9f ] Since commit 1fb87b8e ("perf machine: Don't search for active kernel start in __machine__create_kernel_maps"), the __machine__create_kernel_maps() just create a map what start and end are both zero. Though the address will be updated later, the order of map in the rbtree may be incorrect. The commit ee05d217 ("perf machine: Set main kernel end address properly") fixed the logic in machine__create_kernel_maps(), but it's still wrong in function machine__process_kernel_mmap_event(). To reproduce this issue, we need an environment which the module address is before the kernel text segment. I tested it on an aarch64 machine with kernel 4.19.25: [root@localhost hulk]# grep _stext /proc/kallsyms ffff000008081000 T _stext [root@localhost hulk]# grep _etext /proc/kallsyms ffff000009780000 R _etext [root@localhost hulk]# tail /proc/modules hisi_sas_v2_hw 77824 0 - Live 0xffff00000191d000 nvme_core 126976 7 nvme, Live 0xffff0000018b6000 mdio 20480 1 ixgbe, Live 0xffff0000018ab000 hisi_sas_main 106496 1 hisi_sas_v2_hw, Live 0xffff000001861000 hns_mdio 20480 2 - Live 0xffff000001822000 hnae 28672 3 hns_dsaf,hns_enet_drv, Live 0xffff000001815000 dm_mirror 40960 0 - Live 0xffff000001804000 dm_region_hash 32768 1 dm_mirror, Live 0xffff0000017f5000 dm_log 32768 2 dm_mirror,dm_region_hash, Live 0xffff0000017e7000 dm_mod 315392 17 dm_mirror,dm_log, Live 0xffff000001780000 [root@localhost hulk]# Before fix: [root@localhost bin]# perf record sleep 3 [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.011 MB perf.data (9 samples) ] [root@localhost bin]# perf buildid-list -i perf.data 4c4e46c971ca935f781e603a09b52a92e8bdfee8 [vdso] [root@localhost bin]# perf buildid-list -i perf.data -H 0000000000000000000000000000000000000000 /proc/kcore [root@localhost bin]# After fix: [root@localhost tools]# ./perf/perf record sleep 3 [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.011 MB perf.data (9 samples) ] [root@localhost tools]# ./perf/perf buildid-list -i perf.data 28a6c690262896dbd1b5e1011ed81623e6db0610 [kernel.kallsyms] 106c14ce6e4acea3453e484dc604d66666f08a2f [vdso] [root@localhost tools]# ./perf/perf buildid-list -i perf.data -H 28a6c690262896dbd1b5e1011ed81623e6db0610 /proc/kcore Signed-off-by: NWei Li <liwei391@huawei.com> Acked-by: NJiri Olsa <jolsa@kernel.org> Acked-by: NNamhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Kim Phillips <kim.phillips@arm.com> Cc: Li Bin <huawei.libin@huawei.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20190228092003.34071-1-liwei391@huawei.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Martin George 提交于
[ Upstream commit cc2278c413c3a06a93c23ee8722e4dd3d621de12 ] When undergoing state transitions I/O might be requeued, hence we should always call nvme_mpath_set_live() to schedule requeue_work whenever the nvme device is live, independent on whether the old state was live or not. Signed-off-by: NMartin George <marting@netapp.com> Signed-off-by: NGargi Srinivas <sring@netapp.com> Signed-off-by: NHannes Reinecke <hare@suse.com> Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Geert Uytterhoeven 提交于
[ Upstream commit f7299d441a4da8a5088e651ea55023525a793a13 ] If the call to of_gpiochip_scan_gpios() in of_gpiochip_add() fails, no error handling is performed. This lead to the need of callers to call of_gpiochip_remove() on failure, which causes "BAD of_node_put() on ..." if the failure happened before the call to of_node_get(). Fix this by adding proper error handling. Note that calling gpiochip_remove_pin_ranges() multiple times causes no harm: subsequent calls are a no-op. Fixes: dfbd379b ("gpio: of: Return error if gpio hog configuration failed") Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: NMukesh Ojha <mojha@codeaurora.org> Signed-off-by: NLinus Walleij <linus.walleij@linaro.org> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 raymond pang 提交于
[ Upstream commit dd08a8d9a66de4b54575c294a92630299f7e0fe7 ] When CONFIG_VMAP_STACK=y, __pa() returns incorrect physical address for a stack virtual address. Stack DMA buffers must be avoided. Signed-off-by: Nraymond pang <raymondpangxd@gmail.com> Signed-off-by: NJens Axboe <axboe@kernel.dk> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Ralph Campbell 提交于
[ Upstream commit 92c77f7c4d5dfaaf45b2ce19360e69977c264766 ] valid_phys_addr_range() is used to sanity check the physical address range of an operation, e.g., access to /dev/mem. It uses __pa(high_memory) internally. If memory is populated at the end of the physical address space, then __pa(high_memory) is outside of the physical address space because: high_memory = (void *)__va(max_pfn * PAGE_SIZE - 1) + 1; For the comparison in valid_phys_addr_range() this is not an issue, but if CONFIG_DEBUG_VIRTUAL is enabled, __pa() maps to __phys_addr(), which verifies that the resulting physical address is within the valid physical address space of the CPU. So in the case that memory is populated at the end of the physical address space, this is not true and triggers a VIRTUAL_BUG_ON(). Use __pa(high_memory - 1) to prevent the conversion from going beyond the end of valid physical addresses. Fixes: be62a320 ("x86/mm: Limit mmap() of /dev/mem to valid physical addresses") Signed-off-by: NRalph Campbell <rcampbell@nvidia.com> Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Cc: Craig Bergstrom <craigb@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hans Verkuil <hans.verkuil@cisco.com> Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sander Eikelenboom <linux@eikelenboom.it> Cc: Sean Young <sean@mess.org> Link: https://lkml.kernel.org/r/20190326001817.15413-2-rcampbell@nvidia.comSigned-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Steffen Maier 提交于
[ Upstream commit c8206579175c34a2546de8a74262456278a7795a ] If an incoming ELS of type RSCN contains more than one element, zfcp suboptimally causes repeated erp trigger NOP trace records for each previously failed port. These could be ports that went away. It loops over each RSCN element, and for each of those in an inner loop over all zfcp_ports. The trigger to recover failed ports should be just the reception of some RSCN, no matter how many elements it has. So we can loop over failed ports separately, and only then loop over each RSCN element to handle the non-failed ports. The call chain was: zfcp_fc_incoming_rscn for (i = 1; i < no_entries; i++) _zfcp_fc_incoming_rscn list_for_each_entry(port, &adapter->port_list, list) if (masked port->d_id match) zfcp_fc_test_link if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <=== In order the reduce the "flooding" of the REC trace area in such cases, we factor out handling the failed ports to be outside of the entries loop: zfcp_fc_incoming_rscn if (no_entries > 1) <=== list_for_each_entry(port, &adapter->port_list, list) <=== if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <=== for (i = 1; i < no_entries; i++) _zfcp_fc_incoming_rscn list_for_each_entry(port, &adapter->port_list, list) if (masked port->d_id match) zfcp_fc_test_link Abbreviated example trace records before this code change: Tag : fcrscn1 WWPN : 0x500507630310d327 ERP want : 0x02 ERP need : 0x02 Tag : fcrscn1 WWPN : 0x500507630310d327 ERP want : 0x02 ERP need : 0x00 NOP => superfluous trace record The last trace entry repeats if there are more than 2 RSCN elements. Signed-off-by: NSteffen Maier <maier@linux.ibm.com> Reviewed-by: NBenjamin Block <bblock@linux.ibm.com> Reviewed-by: NJens Remus <jremus@linux.ibm.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Al Viro 提交于
[ Upstream commit daf5cc27eed99afdea8d96e71b89ba41f5406ef6 ] free the symlink body after the same RCU delay we have for freeing the struct inode itself, so that traversal during RCU pathwalk wouldn't step into freed memory. Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Reviewed-by: NJeff Layton <jlayton@kernel.org> Signed-off-by: NIlya Dryomov <idryomov@gmail.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Mukesh Ojha 提交于
[ Upstream commit f276e002793cdb820862e8ea8f76769d56bba575 ] if platform_driver_register fails, cleanup the allocated resource gracefully. Signed-off-by: NMukesh Ojha <mojha@codeaurora.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Matteo Croce 提交于
[ Upstream commit b929a500d68479163c48739d809cbf4c1335db6f ] Since commit ad67b74d ("printk: hash addresses printed with %p") at boot "____ptrval____" is printed instead of the trampoline addresses: Base memory trampoline at [(____ptrval____)] 99000 size 24576 Remove the print as we don't want to leak kernel addresses and this statement is not needed anymore. Fixes: ad67b74d ("printk: hash addresses printed with %p") Signed-off-by: NMatteo Croce <mcroce@redhat.com> Signed-off-by: NBorislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190326203046.20787-1-mcroce@redhat.comSigned-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Rafał Miłecki 提交于
[ Upstream commit 4cb6560514fa19d556954b88128f3846fee66a03 ] Renaming a netdev-trigger-tracked interface was resulting in an unbalanced dev_hold(). Example: > iw phy phy0 interface add foo type __ap > echo netdev > trigger > echo foo > device_name > ip link set foo name bar > iw dev bar del [ 237.355366] unregister_netdevice: waiting for bar to become free. Usage count = 1 [ 247.435362] unregister_netdevice: waiting for bar to become free. Usage count = 1 [ 257.545366] unregister_netdevice: waiting for bar to become free. Usage count = 1 Above problem was caused by trigger checking a dev->name which obviously changes after renaming an interface. It meant missing all further events including the NETDEV_UNREGISTER which is required for calling dev_put(). This change fixes that by: 1) Comparing device struct *address* for notification-filtering purposes 2) Dropping unneeded NETDEV_CHANGENAME code (no behavior change) Fixes: 06f502f5 ("leds: trigger: Introduce a NETDEV trigger") Signed-off-by: NRafał Miłecki <rafal@milecki.pl> Acked-by: NPavel Machek <pavel@ucw.cz> Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Aditya Pakki 提交于
[ Upstream commit 41f00e6e9e55546390031996b773e7f3c1d95928 ] of_match_device in usb251xb_probe can fail and returns a NULL pointer. The patch avoids a potential NULL pointer dereference in this scenario. Signed-off-by: NAditya Pakki <pakki001@umn.edu> Reviewed-by: NRichard Leitner <richard.leitner@skidata.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Kangjie Lu 提交于
[ Upstream commit fba1bdd2a9a93f3e2181ec1936a3c2f6b37e7ed6 ] In case iscsi_lookup_endpoint fails, the fix returns -EINVAL to avoid NULL pointer dereference. Signed-off-by: NKangjie Lu <kjlu@umn.edu> Acked-by: NManish Rangankar <mrangankar@marvell.com> Reviewed-by: NMukesh Ojha <mojha@codeaurora.org> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Dave Carroll 提交于
[ Upstream commit b6554cfe09e1f610aed7d57164ab7760be57acd9 ] There are a few windows during AER/EEH when we can access PCIe I/O mapped registers. This will harden the access to insure we do not allow PCIe access during errors Signed-off-by: NDave Carroll <david.carroll@microsemi.com> Reviewed-by: NSagar Biradar <sagar.biradar@microchip.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Sreekanth Reddy 提交于
[ Upstream commit c2fe742ff6e77c5b4fe4ad273191ddf28fdea25e ] During expander reset handling, the driver invokes kernel function scsi_host_find_tag() to obtain outstanding requests associated with the scsi host managed by the driver. Driver loops from tag value zero to hba queue depth to obtain the outstanding scmds. But when blk-mq is enabled, the block layer may return stale entry for one or more requests. This may lead to kernel panic if the returned value is inaccessible or the memory pointed by the returned value is reused. Reference of upstream discussion: https://patchwork.kernel.org/patch/10734933/ Instead of calling scsi_host_find_tag() API for each and every smid (smid is tag +1) from one to shost->can_queue, now driver will call this API (to obtain the outstanding scmd) only for those smid's which are outstanding at the driver level. Driver will determine whether this smid is outstanding at driver level by looking into it's corresponding MPI request frame, if its MPI request frame is empty, then it means that this smid is free and does not need to call scsi_host_find_tag() for it. By doing this, driver will invoke scsi_host_find_tag() for only those tags which are outstanding at the driver level. Driver will check whether particular MPI request frame is empty or not by looking into the "DevHandle" field. If this field is zero then it means that this MPI request is empty. For active MPI request DevHandle must be non-zero. Also driver will memset the MPI request frame once the corresponding scmd is processed (i.e. just before calling scmd->done function). Signed-off-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Sekhar Nori 提交于
[ Upstream commit 2dbed152e2d4c3fe2442284918d14797898b1e8a ] allnoconfig build with just ARCH_DAVINCI enabled fails because drivers/clk/davinci/* depends on REGMAP being enabled. Fix it by selecting REGMAP_MMIO when building in DaVinci support. Signed-off-by: NSekhar Nori <nsekhar@ti.com> Reviewed-by: NDavid Lechner <david@lechnology.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-
由 Jean-Philippe Brucker 提交于
[ Upstream commit 2d8f92897ad816f5dda54b2ed2fd9f2d7cb1abde ] meson_drv_unbind() doesn't unregister the IRQ handler, which can lead to use-after-free if the IRQ fires after unbind: [ 64.656876] Unable to handle kernel paging request at virtual address ffff000011706dbc ... [ 64.662001] pc : meson_irq+0x18/0x30 [meson_drm] I'm assuming that a similar problem could happen on the error path of bind(), so uninstall the IRQ handler there as well. Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com> Acked-by: NNeil Armstrong <narmstrong@baylibre.com> Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-2-jean-philippe.brucker@arm.comSigned-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>
-