Check O_DIRECT and return -EINVAL error in open.  dentry_open() also checks
this but only after the open method is called.  This patch optimizes away
the unnecessary upcalls in this case.

It could be a correctness issue too: if filesystem has open() with side
effect, then it should fail before doing the open, not after.
Signed-off-by: NMiklos Szeredi <miklos@szeredi.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Calling truncate() on hostfs spits a kernel warning "Something isn't
implemented here", but it still works fine.

Indeed, hostfs i_op->truncate doesn't do anything.  But hostfs_setattr() ->
set_attr() correctly detects ATTR_SIZE and calls truncate() on the host.  So
we should be safe (using ftruncate() may be better, in case the file is
unlinked on the host, but we aren't sure to have the file open for writing,
and reopening it would cause the same races; plus nobody should expect UML to
be so careful).

So, the warning is wrong, because the current implementation is working.  Al,
am I correct, and can the warning be therefore dropped?

CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Revert commit 12ebcd73, i.e.  [PATCH] uml: run
mconsole "sysrq" in process context on request from Jeff Dike.

a) sysrq may be run when the scheduler is non-functioning

b) the warning I wanted to fix actually came from the fault handler run in
   atomic context.  But I fixed that not to take the semaphore in a separate
   patch.

c) the fault handler is run because of a fault, and that fault was
   unaffected by this patch.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

SEGV_MAYBE_FIXABLE tests ptrace_faultinfo, and depends on it being 1 only in
SKAS3 mode, while currently when running with mode=tt it will be 1 anyway.
Fix this, and do the same for proc_mm.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I hadn't been running a SKAS3 host when testing the "uml: fix hang in TT mode
on fault" patch (commit 546fe1cb), and I
didn't think enough to the missing trap_no in SKAS3 mode.

In fact, the resulting kernel doesn't work at all in SKAS3 mode.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

GPIO fix for the composite and tv mute states of bt8xx card #135: DViCO
FusionHDTV5 Lite.  Without this patch, selecting one of these states could
produce unexpected behavior.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

include/asm/hw_irq.h:70: warning: `struct hw_interrupt_type' declared inside parameter list
include/asm/hw_irq.h:70: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Recently aio_p{read,write} changed to perform retries internally rather
than returning -EIOCBRETRY.  This inadvertantly resulted in always calling
aio_{read,write} with ki_left at 0 which would in turn immediately return
0.  Harmless, but we can avoid this call by checking in the caller.
Signed-off-by: NZach Brown <zach.brown@oracle.com>
Signed-off-by: NBenjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Only one of the run or kick path is supposed to put an iocb on the run
list.  If both of them do it than one of them can end up referencing a
freed iocb.  The kick path could delete the task_list item from the wait
queue before getting the ctx_lock and putting the iocb on the run list.
The run path was testing the task_list item outside the lock so that it
could catch ki_retry methods that return -EIOCBRETRY *without* putting the
iocb on a wait queue and promising to call kick_iocb.  This unlocked check
could then race with the kick path to cause both to try and put the iocb on
the run list.

The patch stops the run path from testing task_list by requring that any
ki_retry that returns -EIOCBRETRY *must* guarantee that kick_iocb() will be
called in the future.  aio_p{read,write}, the only in-tree -EIOCBRETRY
users, are updated.
Signed-off-by: NZach Brown <zach.brown@oracle.com>
Signed-off-by: NBenjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Only one of the run or kick path is supposed to put an iocb on the run
list.  If both of them do it than one of them can end up referencing a
freed iocb.  The kick patch could set the Kicked bit before acquiring the
ctx_lock and putting the iocb on the run list.  The run path, while holding
the ctx_lock, could see this partial kick and mistake it for a kick that
was deferred while it was doing work with the run_list NULLed out.  It
would then race with the kick thread to add the iocb to the run list.

This patch moves the kick setting under the ctx_lock so that only one of
the kick or run path queues the iocb on the run list, as intended.
Signed-off-by: NZach Brown <zach.brown@oracle.com>
Signed-off-by: NBenjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

As requested by Thomas Gleixner <tglx@linutronix.de>:

  "5d3d0f77 breaks a couple of ARM
   boards, which depend on the historical bootmem allocation order.
   There is a cleaner solution around to remove the pgdat list
   completely, but this is a topic for post 2.6.14

   Andi signalled ACK already."
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The following patch updates the way SELinux classifies and handles IP
based protocols.

Currently, IP sockets are classified by SELinux as being either TCP, UDP
or 'Raw', the latter being a default for IP socket that is not TCP or UDP.

The classification code is out of date and uses only the socket type
parameter to socket(2) to determine the class of IP socket.  So, any
socket created with SOCK_STREAM will be classified by SELinux as TCP, and
SOCK_DGRAM as UDP.  Also, other socket types such as SOCK_SEQPACKET and
SOCK_DCCP are currently ignored by SELinux, which classifies them as
generic sockets, which means they don't even get basic IP level checking.

This patch changes the SELinux IP socket classification logic, so that
only an IPPROTO_IP protocol value passed to socket(2) classify the socket
as TCP or UDP.  The patch also drops the check for SOCK_RAW and converts
it into a default, so that socket types like SOCK_DCCP and SOCK_SEQPACKET
are classified as SECCLASS_RAWIP_SOCKET (instead of generic sockets).

Note that protocol-specific support for SCTP, DCCP etc. is not addressed
here, we're just getting these protocols checked at the IP layer.

This fixes a reported problem where SCTP sockets were being recognized as
generic SELinux sockets yet still being passed in one case to an IP level
check, which then fails for generic sockets.

It will also fix bugs where any SOCK_STREAM socket is classified as TCP or
any SOCK_DGRAM socket is classified as UDP.

This patch also unifies the way IP sockets classes are determined in
selinux_socket_bind(), so we use the already calculated value instead of
trying to recalculate it.
Signed-off-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NStephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I need the following patch to compile -git8 here, otherwise these
files fail to compile (asm/hw_irq.h needs definitions from
linux/irq.h and that file provides the required include ordering).

I did not do a full audit, though there looks to be many other
places that should get the same treatment, if this is  the right
way to do it.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

the free_irq() in USB suspend breaks resume on some setups where USB
(ohci/ehci) shares the interrupt with an other device.
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

x86-64: Add missing () around arguments of pte_index macro
Signed-Off-By: NAlexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-Off-By: NKirill Korotaev <dev@sw.ru>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

BUILD_BUG_ON(1) is asking for trouble (and getting it) when used in that
manner - dead code elimination happens after we parse it and invalid
type is invalid type, dead code or not.

It might be version-dependent, but at least 4.0.1 refuses to accept
that.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Switched cpuset_common_file_read() to simple_read_from_buffer(), killed
a bunch of useless (and not quite correct - e.g.  min(size_t,ssize_t))
code.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - __user annotations
 - NULL noise removal
 - C99 initializers
 - s/u32/pm_message_t/ in ->suspend()
 - removal of bogus casts in iounmap() arguments
 - if_mii() instead of open-coded variant

Remains to be done: ethtool conversion.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Gen FUKATSU

Invalidate BTB entry instruction flushes two instruction
at a time. Therefore this instruction should be done four
times after invalidate instruction cache line.

Signed-off-by: Gen Fukatsu
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Catalin Marinas

The warning is caused by the gic_set_cpu() function being defined but not
used if CONFIG_SMP is not defined.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Catalin Marinas

When CONFIG_CPU_CACHE_VIPT is defined, the flush_pfn_alias() function is
implicitely declared and it later conflicts with its actual definition.
This patch moves the function definition to the beginning of the file.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

- __user annotations
- NULL noise removal
- C99 initializers
- s/u32/pm_message_t/ in ->suspend()
- removal of bogus casts in iounmap() arguments
- if_mii() instead of open-coded variant

Remains to be done: ethtool conversion.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHorms <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver does a readl() on DEVICE_ID which is 2-byte aligned and
2-bytes in size.  It's doing this read just to flush write buffers.

Create IN16() and OUT16() macros, and use the former to do this I/O
load.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Use cpudata cache line sizes, not magic constants.
2) Align start address in cheetah case so we do not get
   unaligned address traps.  (pgrep was good at triggering
   this, via /proc/${pid}/cmdline accesses)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No longer used.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete all of the code working with sp_banks[] and replace
with clean acquisition and sorting of physical memory
parameters from the firmware.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Scott Talbert <scott.talbert@lmco.com>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Scott Talbert <scott.talbert@lmco.com>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>

Handle better the case where the sender sends full sized
frames initially, then moves to a mode where it trickles
out small amounts of data at a time.

This known problem is even mentioned in the comments
above tcp_grow_window() in tcp_input.c, specifically:

...
 * The scheme does not work when sender sends good segments opening
 * window and then starts to feed us spagetti. But it should work
 * in common situations. Otherwise, we have to rely on queue collapsing.
...

When the sender gives full sized frames, the "struct sk_buff" overhead
from each packet is small.  So we'll advertize a larger window.
If the sender moves to a mode where small segments are sent, this
ratio becomes tilted to the other extreme and we start overrunning
the socket buffer space.

tcp_clamp_window() tries to address this, but it's clamping of
tp->window_clamp is a wee bit too aggressive for this particular case.

Fix confirmed by Ion Badulescu.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>