Instead of on the stack.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All features originally planned for version 3.1 (and some that
weren't) have been implemented.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

In Falcon we can configure the fill levels of the RX data FIFO which
trigger the generation of pause frames (if enabled), and we have
module parameters for this.

Siena does not allow the levels to be configured (or, if it does, this
is done by the MC firmware and is not configurable by drivers).

So far as I can tell, the module parameters are not used by our
internal scripts and have not been documented (with the exception of
the short parameter descriptions).  Therefore, remove them and always
initialise Falcon with the default values.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This field does not exist in all MMDs we want to check, and all
callers allow it to be set (fault_fatal = 0).

Remove the loopback condition, as STAT2.DEVPRST should be valid
regardless of any fault.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We currently make no use of siena_nic_data::fw_{version,build} except
to format the firmware version for ethtool_get_drvinfo().  Since we
only read the version at start of day, this information is incorrect
after an MC firmware update.  Remove the cached version information
and read it via MCDI whenever it is requested.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Instead calculate the KVA of receive data. It's not like it's a hard sum.

[bwh: Fixed to work with GRO.]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

[bwh: Forward-ported to net-next-2.6.]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Clearly it should be the size of ->ip_dst here.
Although this is harmless, but it still reads odd.
Signed-off-by: NWANG Cong <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a port profile disassociate all address registrations for the interface
are blown away from the adapter. This patch resets the driver cache of
registered address lists to zero after a port profile disassociate.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow randomised ethernet address if the device does not have a valid
EEPROM or pre-set MAC address.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add necessary annotations about pointer to io memory space
that is checked by sparse.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix use of zero where NULL expected. And wrap long line.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so it wasn't
converted by commit 44c10138 (PCI: Change all
drivers to use pci_device->revision).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With this patch the bnx2x uses the generic dcbnl application tlv list
instead of implementing its own get-app handler. When the driver is
alerted to a change in the DCB negotiated parameters, it calls
dcb_setapp to update the dcbnl application tlvs list making it available
to user mode applications and registered notifiers.   
Signed-off-by: NShmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several more network drivers that read the device's revision ID
from the PCI configuration register were merged after the commit
44c10138 (PCI: Change all drivers
to use pci_device->revision), so it's time to do another pass of
conversion to using the 'revision' field of 'struct pci_dev'...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: N"John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts bonding to use rx_handler. Results in cleaner
__netif_receive_skb() with much less exceptions needed. Also
bond-specific work is moved into bond code.

Did performance test using pktgen and counting incoming packets by
iptables. No regression noted.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Reviewed-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

V4: rebase to net-next-2.6

This patch removes the flag IFF_IN_NETPOLL, we don't need it any more since
we have netpoll_tx_running() now.
Signed-off-by: NWANG Cong <amwang@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

V4: rebase to net-next-2.6
V3: remove an useless #ifdef.

This patch unifies the netpoll code in bonding with netpoll code in bridge,
thanks to Herbert that code is much cleaner now.
Signed-off-by: NWANG Cong <amwang@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will synchronize the version with the out of tree driver which
shares its functionality.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fix updates copyright information to include current year 2011.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implemented igb_ndo_set_vf_bw function which is being used
by iproute2 tool. In addition, updated igb_ndo_get_vf_config function
to show the actual rate limit to the user.

The rate limitation can be configured only when the link is up.
The rate limit value can be ranged between 0 and actual
link speed measured in Mbps. A value of '0' disables the rate limit for
this specific VF.

iproute2 usage will be 'ip link set ethX vf Y rate Z'.
After the command is made, the rate will be changed instantly.
To view the current rate limit, use 'ip link show ethX'.

The rates will be zeroed only upon driver reload or a link speed change.

This feature is being supported only by 82576 device.
Signed-off-by: NLior Levy <lior.levy@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removed Tx hang detection mechanism from igbvf.
This mechanism has no affect and can cause false alarm message in some cases.
Signed-off-by: NLior Levy <lior.levy@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of the function names in function header comments did not match
actual name of the function.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X540 controller allows jumbo frame setup on a per VF basis.  Enable
use of jumbo frames when the VF device belongs to the X540 controller.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X540 controller supports jumbo frames in SR-IOV mode.  Allow
configuration of jumbo frames either in the PF driver or on behalf of
a VF.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Max rx queues and tx queues are governed by fimware.
So driver should not validate these values.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Remove checks of 1 for auto_fw_reset module parameter.
  auto_fw_reset is of type int and can have value > 1.
o Remove unnecessary #define for 1
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original code does not work well when the number of mulitcast
address to handle is greater than MCAST_MAX. It only enable promiscous
mode instead of multicast hash table mode, so the hash table function
will not be activated and all multicast frames will be recieved in this
condition.

This patch fixes the following issues with the r6040 NIC operating in
multicast:

1) When the IFF_ALLMULTI flag is set, we should write 0xffff to the NIC
hash table registers to make it process multicast traffic.

2) When the number of multicast address to handle is smaller than
MCAST_MAX, we should use the NIC multicast registers MID1_{L,M,H}.

3) The hashing of the address was not correct, due to an invalid
substraction (15 - (crc & 0x0f)) instead of (crc & 0x0f) and an
incorrect crc algorithm (ether_crc_le) instead of (ether_crc).

4) If necessary, we should set HASH_EN flag in MCR0 to enable multicast
hash table function.
Reported-by: NMarc Leclerc <marc-leclerc@signaturealpha.com>
Tested-by: NMarc Leclerc <marc-leclerc@signaturealpha.com>
Signed-off-by: NShawn Lin <shawn@dmp.com.tw>
Signed-off-by: NAlbert Chen <albert.chen@rdc.com.tw>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dmaw_block is an enum and max_pay_load is u32. Therefore
sparse gives warning about comparison of unsigned and signed value.
Resolve by using min_t to force cast.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use hba_port_num for phy loopback and ethtool phy identification.

From: Suresh R <suresh.reddy@emulex.com>
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to display temperature of ASIC via ethtool -S

From: Somnath K <somnath.kotur@emulex.com>
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With transparent VLAN tagging, the ASIC wrongly indicates packets with VLAN ID.
Strip them off in the driver. The VLAN Tag to be stripped will be given to the host
as an async message.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

change occurances of stats_ioctl_sent to stats_cmd_sent
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

> add missing separator between items in ethtool self_test array
> fix reporting of test resluts when link is down and
  when selftest command fails.

From: Suresh R <suresh.reddy@emulex.com>
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New counters:
	> jabber frame stats
	> red drop stats
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit supports following functions.
  - get_settings
  - set_settings
  - nway_reset
  - get_msglevel
  - set_msglevel
  - get_link
  - get_strings
  - get_ethtool_stats
  - get_sset_count

About other function, the device does not support.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>