Now that there is no need to hookup on the open/close of the joystick,
it's possible to use the simplified interface input_polled_device, instead
of creating our own kthread.

[randy.dunlap@oracle.com: fix Kconfig]
[randy.dunlap@oracle.com: fix Kconfig some more]
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf

These sensors communicate over a 2 wire bus running a device specific
protocol.  The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available.  This is handled by
an interrupt that is disabled under all other conditions.

I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!

Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem.  If not it should be provided in the
platform data.

I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: NMatthew Palmer <mpalmer@debian.org>
Signed-off-by: NLaurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.

There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).

Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Make use of the new abstraction layer and add a new transport layer for
spi.  Works fine on a PXA based board.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.

I have tested the driver with my board, and it appears to work fine.  With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power.  With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power.  I'm not drawing any current at the
moment, so this is reasonable.  The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.

I didn't attempt to support changing any of the chip's settings or
enabling the FET.  I'm not sure even how to do that and still fit within
the hwmon framework.  :)
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

An hwmon driver for the National Semiconductor LM95241 triple temperature
sensors chip
Signed-off-by: NDavide Rizzo <elpa-rizzo@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the Hades to the FSC hwmon driver.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Many thanks to Fujitsu Siemens Computers for providing docs and a
machine to test the driver on.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.

If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>

Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.

At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: NGong Jun <JGong@nuvoton.com>
Acked-by: NDavid Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Update documentation to prevent further confusion/duplication.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver.  From a purely Linux developer's point of view,
the led and the accelerometer have nothing related.  However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module.  Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hwmon driver for the ADT7475 chip.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution.  This patch extends the
LM70 driver to support the TMP121.  The TMP123 differs in pin assign-
ment.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Now that the new merged fschmd driver has gained support for the watchdog
integrated into these IC's, there is no more reason to keep the old fscher
and fscpos drivers around, so mark them as deprecated.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch adds support for the watchdog part found in _all_ supported FSC
sensor chips.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: NJean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

New driver to play with.  As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors.  This driver has been tested on an IntelliStation Z30.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard").  It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.

This driver was first written by Yan Burman.  Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now).  Pavel Machek removed few more features and switched locking from
semaphore to mutex.

Several people have contributed to the database of the axes.

[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NYan Burman <burman.yan@gmail.com>
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC.  Adjust the
register conversion functions accordingly.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NMartyn Welch <martyn.welch@gefanuc.com>

Driver based on corgi_ssp.c and sharpsl_pm.c, previously done by Richard
Purdie and many others.

Now changed to generic HWMON device and expose all the ADC input value
through sysfs.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is a PIC16F747 based controller that monitors and consolidates
the hardware access to various fan and temperature values reported by
adr7462 and similar devices behind an I2C bus.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...

Code for 8 channels by Tobias Himmer.

This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:

 * bb  is the resolution in number of bits (8, 10, 12)
 * c   is the number of channels (1, 2, 4, 8)
 * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
   kSPS and 101 for 1 MSPS)

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Cc: Tobias Himmer <tobias@himmer-online.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Driver for the Analog Devices AD7414 temperature monitoring chip.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The adm9240 driver is in the kernel for three years now, time to
remove the EXPERIMENTAL dependency.
Signed-off-by: NGrant Coady <gcoady.lk@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
  and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: NJuerg Haefliger <juergh@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

More LM75 updates:

 - Teach the LM75 driver to use new-style driver binding:

     * Create a second driver struct, using new-style driver binding
       methods cribbed from the legacy code.

     * Add a MODULE_DEVICE_TABLE (for "newER-style binding")

     * The legacy probe logic delegates its work to this new code.

     * The legacy driver now uses the name "lm75_legacy".

 - More careful initialization.  Chips are put into 9-bit mode so
   the current interconversion routines will never fail.

 - Save the original chip configuration, and restore it on exit.
   (Among other things, this normally turns off the mode where
   the chip is constantly sampling ... and thus saves power.)

So the new-style code should catch all chips that boards declare,
while the legacy code catches others.  This particular coexistence
strategy may need some work yet ... legacy modes might best be set
up explicitly by some tool not unlike "sensors-detect".  (Or else
completely eradicated...)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Minor cleanup and reorg of the lm75 code.

 - Kconfig provides a larger list of lm75-compatible chips

 - A top comment now says what the driver does (!) ... as in, just
   what sort of sensor is this??

 - Section comments now delineate the various sections of the driver:
   hwmon attributes, driver binding, register access, module glue.
   One driver binding function moved out of the attribute section,
   as did the driver struct itself.

 - Minor tweaks to legacy probe logic:  correct a comment, and
   remove a pointless variable.

 - Whitespace, linelength, and comment fixes.

This patch should include no functional changes.  It's preparation
for adding new-style (driver model) I2C driver binding.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This driver reads IBM Active Energy Manager energy/temperature/power
sensors on IBM System X hardware.

[akpm@linux-foundation.org: fix printk warnings]
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enhanced the list of supported machines.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Signed-off-by: NSteve Hardy <steve@linuxrealtime.co.uk>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

The W83627HF hardware monitoring features are supported by the
w83627hf driver for several years now. Support by the w83781d has
been advertised as deprecated 6 months ago, it's about time to see
it go.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

It happens that the Analog Devices ADM1024 is fully compatible with
the National Semiconductor LM87, so support for the former can easily
be added to the lm87 driver.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Signed-off-by: NKevin Lo <kevlo@kevlo.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

New driver to read FB-DIMM temperature sensors on systems with the
Intel 5000 series chipsets.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>