With the new connection flow, start_sta is called before
the remote rates where updated. Use our own supported rates
instead to make sure we don't disable any potential rate
(the rate policies will be updated later, but there is
currently no way to update the remote rates)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Pass a variable indicating whether HT is enabled,
instead of duplicating the function call with
different arguments.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When first configuring the rate policy, before auth,
we still don't have the correct rates that were
agreed during association.

Reconfigure the rate policy on association in order
to update them.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The supported_rates field should contain all our supported
rates, even if the remote peer doesn't support them.

(rename CONF_TX_AP_ENABLED_RATES to CONF_TX_ENABLED_RATES,
as we now use it for both ap and sta)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The default ps mode of the fw is auto, while the default
ps mode of mac80211 is active (ps off).
In order to sync them, configure active ps on association.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Use the sta_state notifications to ROC when a station
is about to connect, and CROC respectively on
authorization (success) / deletion (failure).

Change the wl12xx_update_sta_state() flow to bail out
only on error, so multiple code blocks could refer
to the same state.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add some basic chanctx implementation - debug prints,
and save the vif's channel/band/type.

After that, we no longer need to handle channel change
notifications on op_config.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We care only about the operational channel, not
about the temporal hw channel (which won't have
any real meaning in multi-channel env anyway)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

implement the reamin_on_channel() callback by starting
a dev role (already associated with the current vif)
on the requested channel/band.

This channel is usually different from the channel
of the sta role, so pass it to wl12xx_roc() as well,
and notify mac80211 (async) when the fw is ready
on the new channel.

Now, in case of offchannel tx, we should use the dev
role hlid, instead of the sta hlid.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

for some reason, the wl12xx fw is not able to rx/tx
on the first start_sta cmd.
Workaround it by issuing a dummy start_sta + stop_sta
before starting the sta for the final time.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Make the connection flow simpler by starting
sta role on bssid change.

Currently, we start dev role when going idle-off,
and start the sta role only after association
indication. This complicates the connection
flow with some possible intermediate states.

Make it simpler by starting sta role on bssid change,
which now happens *before* auth req get sent.

Update the handling of mac80211's notifications
and change wl1271_join/unjoin accordingly -
* Split wl1271_join() into wlcore_join (tuning on
  a channel/bssid) and wlcore_set_assoc (configure
  sta after association).
* Rename wl1271_unjoin() to wlcore_unset_assoc(), as
  it is no longer the inversion of wl1271_join()
  (now it's only used to disconnect associated sta /
  joined ibss, without stopping the role).
* Set ssid before starting station role (needed for
  start_role(sta)

While on it, split wl1271_bss_info_changed_sta() into
some sub-functions.

since we no longer use dev role in the connection flow,
we now always use the hlid of the sta role.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

No need to check whether unsigned variable is less than 0.

CC: Luciano Coelho <coelho@ti.com>
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.

So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: Nliu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

In corner case for wl12xx_spi_raw_write() when
	len == SPI_AGGR_BUFFER_SIZE
we don't setup correctly spi transfer_list.
Next we will have garbage and strange errors
reported by SPI framework (eg. wrong speed_hz,
failed to transfer one message from queue)
when iterate transfer_list.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.

Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases.  All other usage is a bug.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.

Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases.  All other usage is a bug.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The function wl12xx_set_power_on is only called twice, once in
wl12xx_chip_wakeup and once in wl12xx_get_hw_info.  On the failure of the
call in wl12xx_chip_wakeup, the containing function just returns, but on
the failure of the call in wl12xx_get_hw_info, the containing function
calls wl1271_power_off.  This does not seem necessary, because if
wl12xx_set_power_on has set the power on and then fails, it has already
turned the power off.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier f,free,a;
parameter list[n] ps;
type T;
expression e;
@@

f(ps,T a,...) {
  ... when any
      when != a = e
  if(...) { ... free(a); ... return ...; }
  ... when any
}

@@
identifier r.f,r.free;
expression x,a;
expression list[r.n] xs;
@@

* x = f(xs,a,...);
  if (...) { ... free(a); ... return ...; }
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

wlcore_op_set_key() calls wl18xx_set_key(),
which in turn executes some of his function
calls without acquiring wl->mutex and making
sure the fw is awake.

Adding mutex_lock()/ps_elp_wakeup() calls is
not enough, as wl18xx_set_key() calls
wl1271_tx_flush() which can't be called while
the mutex is taken.

Add the required calls to wlcore_op_set_key,
but limit the queues_stop and flushing
to the only encryption types in which
a spare block might be needed (GEM and TKIP).

[Arik - move state != ON check]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The current elp timeout (the same as the dynamic
ps timeout - 1500ms) is too high. Usually,
wl1271_ps_elp_sleep() get called right after tx/rx,
which is fine, but some command might get sent
even when there is no traffic (e.g. ht changes
triggered by beacon frames), and leaving the
device awake for 1500ms in this case is redundant.

Use a timeout of 30ms.
The fw won't enter elp anyway before the dynamic-ps
timeout was expired as well (and it entered ps
successfully).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The NVS file is loaded by the device's probe callback with the help of
request_firmware(). Since request_firmware() relies on udevd, the
modules cannot be loaded before hotplug events are handled.

Fix this by loading the NVS file asynchronously and continue
initialization only after the firmware request is over.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Move most of the device-specific probe functionality into setup(), a new
op. By doing this, wlcore_probe will be the first to request a firmware
from userspace, making it easier to load the NVS file asynchronously.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

When the no_recovery flag is used, the recovery work will not restart
the FW and the state will not be set to 'on'. To enable post-mortem
analysis, allow memory access in the 'restarting' state.

Also, since the FW might not be operational, don't fail the read/write
operations if elp_wakeup fails.
Reported-by: NArkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Currently, all the (station) roles use the same
keep-alive template id (0). However, the klv
template ids shouldn't be shared by different
roles.

Implement a simple klv_templates bitmap, and let
each role allocate its own klv template id on
role initialization.

[Arik - remove invalidation of KLV template when getting into "idle".
This is already handled in unjoin]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Previously, invalidation of the keep-alive template was
done when going idle. However, while removing the
idle-handling we didn't move the keep-alive template
invalidation to another place.

This finally resulted in fw error when trying to use
the keep-alive template by another role.

(Note that we still have an error here - each role
should have its unique keep-alive template id, while
currently they all use CMD_TEMPL_KLV_IDX_NULL_DATA (0).
This only works now because we don't support concurrent
connected stations yet)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

While recursive recovery is avoided during shutdown, a new recovery may
be queued when the FW boots. The recovery work will then try to stop an
already stopped hardware, which will most likely result in a kernel
panic.

Fix this by verifying that wl->state is on before queueing a new
recovery.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

add phy_fw_version_str to debugfs driver_state file.
information is taken during boot and stored in wl->chip.phy_fw_ver_str.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Limit SPI transmissions to the wl12xx max buffer size, as only 12xx was
tested with SPI.

This allows us to remove the global aggregation buffer constant.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

This allows us to have a p2p-management interface (in STA mode),
as we as a group dedicated interface.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Enable device roles just before starting it.
This way, a single device role should be enough
for all vifs, as we can't use concurrent device
roles (which require ROC) anyway.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

enabled (but not-started) sta role should be good enough
for scanning (both normal and scheduled), so use it
instead of the device_role.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Make debug prints operational when dynamic debug is not defined.
This allows better debugging in production environments.

Change the driver prefix to "wlcore" while were at it.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Allow 3 native mac addresses on 18xx. On 12xx allow 2 native mac
addresses and set the LAA bit to create a third mac address. This
enabled operation with a separate group interface.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

mac80211's resume() callback might get called even if
the sta is not associated (but only up). The
resume sequence in this case results in configuring
the wake-up conditions of a non-started role, which
causes fw assertion.

Fix it by bailing out if the STA is not connected
(like we do on suspend()).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

wowlan filters should be configured in any case in suspend/resume.
This shouldn't be dependent on whether wakeup conditions are the
same for suspend and resume states. Only the FW command to
reconfigure wakeup conditions should be avoided in such a case.
Reported-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Aggregation buffer size is set separately per 18xx/12xx chip family.
For 18xx aggragation buffer is set to 13 pages to utilize all
the available tx/rx descriptors for aggregation.

[Arik - remove redundant parts from the patch]
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Force Tx during the flush if there are packets pending in the driver.
This actually solves a bug where we would get called from the mac80211
wq context, which would prevent tx_work from getting queued, even when
the mutex is unlocked.

Don't stop the queues needlessly if there's nothing to flush. Use a
larger delay when sleeping to give the driver a chance to flush and
avoid cpu busy looping. Re-arrange the loop so the last iteration is
not wasted.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Print how much time a flush took. This will help debug the time it takes
to switch between channels.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The IEEE80211_TX_CTL_NO_CCK_RATE flag is only set for mgmt packets
transmitted during p2p connection setup. Make sure to use the lowest
OFDM rate guarantee the peer always hears us.
Change the p2p rate policy to contain only the 6mpbs rate to acheive
this effect.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

This solves interoperability issues with peer that don't seem to "hear"
management packets transmitted in higher rates. Based on a previous
patch by Igal Chernobelsky.

Cc: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

recovery_work should be cancelled when stopping the device,
not when removing an interface (this is probably a leftover
from the single-role days)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>