DSS IP versions 2 and 3 support CLUT modes (color lookup table), but the
driver has never supported those. We still have had some code for CLUT
modes. As the newer DSS IP versions have dropped CLUT support, we might
as well clean up the driver by removing the CLUT related code.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The code that sets and clears DOUBLESTRIDE is only ran when using NV12.
This is not correct, as we might first set the bith when using NV12, but
never clear it when using other formats.

Fix it so that when the bit is available (when the HW supports NV12) we
always either set or clear the bit.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The omap_dss_find_output() function is unused, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Structs omap_overlay and omap_overlay_manager are not used, remove them.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove unused fields in struct omap_dss_device.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

get_resolution is not used, remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

get_dimensions function pointer is not used, remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The RFBI driver has not worked nor compiled for many years. There are
very few boards out there that use RFBI, and no one has stepped up to
fix it.

So let's remove the RFBI code that doesn't even compile.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove DPI's legacy data_lines code.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

recommended_bpp hasn't been used for ages, remove the code.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

We only use read_irqenable() to flush posted write. Instead of having a
separate function for this, do the flush implicitly in write_irqenable().
Thus we can remove read_irqenable().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

At the moment we have ovl_set_channel_out() to configure the output
channel of an overlay. It makes sense to have this configuration as part
of the rest of overlay configuration, and in DSS6+ we need the output
channel when doing the other overlay configuration.

This patch adds a 'channel' parameter to ovl_setup(), so that all
overlay configuration is done via the same function, and removes the
ovl_set_channel_out().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

ovl_enabled() is not used anywhere, so remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The SDI platform driver was used for non-DT platforms only. On DT
platforms the SDI port is handled manually. As OMAP display devices are
now instantiated from DT only, remove the SDI platform driver.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DPI platform driver was used for non-DT platforms only. On DT
platforms the DPI port is handled manually. As OMAP display devices are
now instantiated from DT only, remove the DPI platform driver.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The default display name is both unused and never set by platform data.
Remove default display name module parameter, platform data field and
runtime infrastructure.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The dss_get_core_pdev() function is unused, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All OMAP platforms use DT nowadays, drop support for non-DT devices.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The devm_ioremap_resource() call can handle being given a NULL resource,
and prints an error message when mapping fails. Switch the remaining
devm_ioremap() calls to devm_ioremap_resource() and remove all
extraneous resource NULL checks and error messages printed manually by
the driver.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The OMAP driver has its own OF graph helpers that are similar to the
common helpers. This commit replaces most of the calls with the common
helpers. There's still a couple of custom helpers left, but the driver
needs more extensive changes to get rid of them.

In dss_init_ports, we invert the loop, looping through the known ports
and matching them to DT nodes rather than looping thru DT nodes and
matching them to the ports.
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>

Fix one ugly indentation style break left by the previous coccilnelle
patch.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The enum omap_plane conflicted with the same struct name for omapdrm
plane private data. This rename should solve the conflict.

The rename was implement with this very simple coccinelle patch:
------------------------
@@
@@
enum
-omap_plane
+omap_plane_id
------------------------
The patch was applied like this:
spatch --sp-file <cocci_file> --all-includes --in-place --dir drivers/gpu/drm/omapdrm

The above patch did not rename the actual enum definition. That was
added manually on top of the spatch changes.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Instead of printing 0/1 for display flags like vsync high/low, use a
tri-state print (-1/0/1) to indicate the "undefined" state.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Keep the panel_list ordered according to aliases. The DRM connectors will
be created following the panel_list. By keeping the list ordered the DRM
connectors will be created in the same order regardless of the driver
probe order.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When omapdss is loaded (all core components are in place) create a list of
devices used in the display graph. This list later can be used by omapdrm
via the omapdss_stack_is_ready() function to check that these components
are loaded. Based on this information, omapdrm can defer probe in case when
the omapdss stack is not ready yet.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The functions can be used to check a component (by it's of_node) if it is
part of the omapdss display or output list. If the component is found, it
means that the driver is loaded.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS uses "replication logic" to convert color components from smaller
bit widths to bigger bit widths. Without replication logic, the color
component would be shifted and the least significant bits would be left
at 0, whereas with replication logic, the least significat bits will be
filled with the most significant bit.

For some reason omapdrm leaves replication logic always to off, which,
in the most common case, means that showing 16-bit RGB colors on 24-bit
display gives a bit darker colors than expected.

The reset value of the replication logic bit is enabled, and it should
always be set, as there's no practical reason to disable it. This patch
removes the option to disable it from omapdrm, and always sets it to
enabled in dispc.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove two unused WB functions.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdrm now uses dispc_ops instead of direct function calls so we can
remove all EXPORT_SYMBOLs from dispc. Most of the functions can also be
made static, but a few are used outside dispc.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch changes the current omapdss driver to fill a dispc_ops struct
and set it to omapdss-base.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We want to change the dispc API from plain functions to a struct with
functions pointers, so that omapdrm can call either omapdss or omapdss6
depending on the platform.

This patch adds 'struct dispc_ops' and adds functions to omapdss-base
to set and get the ops.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdrm still uses a few non-dispc functions: dss_feat_get_num_mgrs(),
dss_feat_get_num_ovls() and  dss_feat_get_supported_color_modes(). We
want to provide omapdrm a single dispc_ops function pointer struct so
that omapdrm will use either the current omapdss or the new omapdss6
driver depending on the platform.

Those three functions are really dispc functions, but are located in the
dss_features.c for legacy reasons.

This patch adds similar functionss to the dispc, and changes omapdrm to
use those new functions. Underneath the functions still call the
functions from dss_feature.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch moves the common parts of omapdss to omapdss-base so that
both the current omapdss driver and the new omapdss6 driver can use
them.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

display.c uses dsi_get_pixel_size() which is implemented in the DSI
driver, and we won't have that in the omapdss-base module, to which we
want to move display.c

This patch changes display.c not to use dsi_get_pixel_size(). The call
can be replaced with a simple check for OMAP_DSS_DSI_FMT_RGB565.

We can also make dsi_get_pixel_size() static as it's no longer used
outside dsi.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We don't have omapdss's custom error printing functions in the common
omapdss-base module, to which we want to move output.c.

This patch changes output.c to use dev_err instead of DSSERR so that it
doesn't depend on DSSERR.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdss_is_initialized() is used to find out if omapdss has been probed
successfully. This patch moves the related code to the common
omapdss-base module, so that the same support will be there for both
omapdss and omapdss6.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are working towards enabling omapdss6, which will consists of a new
dss, dispc and dpi drivers. omapdss6 will be a new module. The panel,
encoder and omapdrm will need to use either the current omapdss driver
or the new omapdss6 driver, depending on the platform.

This will be implemented with a common base module and function
pointers.

This patch adds a skeleton omapdss-base.ko module, to which we'll be
moving common dss functionality like registration of the panels.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

While implementing writeback support, odd behavior of WBDELAYCOUNT was
observed with the combination of WB capture and HDMI. The result of the
debugging was that the HDMI sync polarities are not set correctly.

The current code sets the sync polarities going from HDMI WP to DISPC
according to the video mode used, which seems to work normally fine, but
causes problems with WB as WB expects the syncs to be active-high.

This patch changes the HDMI sync polarities so that the DISPC always
gets active-high syncs from HDMI WP, and the HDMI core gets sync
polarities according to the used video mode.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>