The enable_kernel_*() functions leave the relevant MSR bits enabled
until we exit the kernel sometime later. Create disable versions
that wrap the kernel use of FP, Altivec VSX or SPE.

While we don't want to disable it normally for performance reasons
(MSR writes are slow), it will be used for a debug boot option that
does this and catches bad uses in other areas of the kernel.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move the MSR modification into new c functions. Removing it from
the low level functions will allow us to avoid costly MSR writes
by batching them up.

Move the check_if_tm_restore_required() check into these new functions.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We used to allow giveup_*() to be called with a NULL task struct
pointer. Now those cases are handled in the caller we can remove
the checks. We can also remove giveup_altivec_notask() which is also
unused.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

mtmsrd_isync() will do an mtmsrd followed by an isync on older
processors. On newer processors we avoid the isync via a feature fixup.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The UP only lazy floating point and vector optimisations were written
back when SMP was not common, and neither glibc nor gcc used vector
instructions. Now SMP is very common, glibc aggressively uses vector
instructions and gcc autovectorises.

We want to add new optimisations that apply to both UP and SMP, but
in preparation for that remove these UP only optimisations.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move all our context switch SPR save and restore code into two
helpers. We do a few optimisations:

- Group all mfsprs and all mtsprs. In many cases an mtspr sets a
scoreboarding bit that an mfspr waits on, so the current practise of
mfspr A; mtspr A; mfpsr B; mtspr B is the worst scheduling we can
do.

- SPR writes are slow, so check that the value is changing before
writing it.

A context switch microbenchmark using yield():

http://ozlabs.org/~anton/junkcode/context_switch2.c

./context_switch2 --test=yield 0 0

shows an improvement of almost 10% on POWER8.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently, if HV KVM is configured but PR KVM isn't, we don't include
a test to see whether we were interrupted in KVM guest context for the
set of interrupts which get delivered directly to the guest by hardware
if they occur in the guest.  This includes things like program
interrupts.

However, the recent bug where userspace could set the MSR for a VCPU
to have an illegal value in the TS field, and thus cause a TM Bad Thing
type of program interrupt on the hrfid that enters the guest, showed that
we can never be completely sure that these interrupts can never occur
in the guest entry/exit code.  If one of these interrupts does happen
and we have HV KVM configured but not PR KVM, then we end up trying to
run the handler in the host with the MMU set to the guest MMU context,
which generally ends badly.

Thus, for robustness it is better to have the test in every interrupt
vector, so that if some way is found to trigger some interrupt in the
guest entry/exit path, we can handle it without immediately crashing
the host.

This means that the distinction between KVMTEST and KVMTEST_PR goes
away.  Thus we delete KVMTEST_PR and associated macros and use KVMTEST
everywhere that we previously used either KVMTEST_PR or KVMTEST.  It
also means that SOFTEN_TEST_HV_201 becomes the same as SOFTEN_TEST_PR,
so we deleted SOFTEN_TEST_HV_201 and use SOFTEN_TEST_PR instead.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Most architectures use NR_syscalls as the #define for the number of syscalls.

We use __NR_syscalls, and then define NR_syscalls as __NR_syscalls.

__NR_syscalls is not used outside arch code, whereas NR_syscalls is. So as
NR_syscalls must be defined and __NR_syscalls does not, replace __NR_syscalls
with NR_syscalls.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The selftest passes on 64-bit LE and 32-bit BE.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Removal started in commit 5bbeed12 ("sparc32: drop unused
kmap_atomic_to_page").  Let's do it across the whole tree.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In order to workaround Erratum A-008139, we have to invalidate the
tlb entry with tlbilx before overwriting. Due to the performance
consideration, we don't add any memory barrier when acquire/release
the tcd lock. This means the two load instructions for esel_next do
have the possibility to return different value. This is definitely
not acceptable due to the Erratum A-008139. We have two options to
fix this issue:
  a) Add memory barrier when acquire/release tcd lock to order the
     load/store to esel_next.
  b) Just make sure to invalidate and write to the same tlb entry and
     tolerate the race that we may get the wrong value and overwrite
     the tlb entry just updated by the other thread.

We observe better performance using option b. So reserve an additional
register to save the value of the esel_next.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

The way VIRT_PHYS_OFFSET is not correct on book3e-64, because
it does not account for CONFIG_RELOCATABLE other than via the
32-bit-only virt_phys_offset.

book3e-64 can (and if the comment about a GCC miscompilation is still
relevant, should) use the normal ppc64 __va/__pa.

At this point, only booke-32 will use VIRT_PHYS_OFFSET, so given the
issues with its calculation, restrict its definition to booke-32.
Signed-off-by: NScott Wood <scottwood@freescale.com>

book3e is different with book3s since 3s includes the exception
vectors code in head_64.S as it relies on absolute addressing
which is only possible within this compilation unit. So we have
to get that label address with got.

And when boot a relocated kernel, we should reset ipvr properly again
after .relocate.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
[scottwood: cleanup and ifdef removal]
Signed-off-by: NScott Wood <scottwood@freescale.com>

Some times it is useful for architecture implementations of KVM to know
when the VCPU thread is about to block or when it comes back from
blocking (arm/arm64 needs to know this to properly implement timers, for
example).

Therefore provide a generic architecture callback function in line with
what we do elsewhere for KVM generic-arch interactions.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

These were introduced in commit 25ae3a07 ("[POWERPC] mpc512x: Add
MPC512x PSC support to MPC52xx psc driver") and never used. Moreover
according to the datasheet[1] MEMERROR is bit 25 (0x40) and ORERR is
bit 27 (0x10).

[1] MPC5125RM Rev. 2; 11/2009
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

This driver for Freescale MPC512x LocalPlus Bus FIFO (called SCLPC
in the Reference Manual) allows Direct Memory Access transfers
between RAM and peripheral devices on LocalPlus Bus.
Signed-off-by: NAlexander Popov <alex.popov@linux.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Freescale's Layerscape ARM chips use the same structure.
Signed-off-by: NScott Wood <scottwood@freescale.com>

This reverts commit 9678cdaa ("Use the POWER8 Micro Partition
Prefetch Engine in KVM HV on POWER8") because the original commit had
multiple, partly self-cancelling bugs, that could cause occasional
memory corruption.

In fact the logmpp instruction was incorrectly using register r0 as the
source of the buffer address and operation code, and depending on what
was in r0, it would either do nothing or corrupt the 64k page pointed to
by r0.

The logmpp instruction encoding and the operation code definitions could
be corrected, but then there is the problem that there is no clearly
defined way to know when the hardware has finished writing to the
buffer.

The original commit attempted to work around this by aborting the
write-out before starting the prefetch, but this is ineffective in the
case where the virtual core is now executing on a different physical
core from the one where the write-out was initiated.

These problems plus advice from the hardware designers not to use the
function (since the measured performance improvement from using the
feature was actually mostly negative), mean that reverting the code is
the best option.

Fixes: 9678cdaa ("Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8")
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch provides individual system call numbers for the following
System V IPC system calls, on PowerPC, so that they do not need to be
multiplexed:
* semop, semget, semctl, semtimedop
* msgsnd, msgrcv, msgget, msgctl
* shmat, shmdt, shmget, shmctl
Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Emulate TMCFG0 TMRN register exposing one HW thread per vcpu.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
[Laurentiu.Tudor@freescale.com: rebased on latest kernel, use
 define instead of hardcoded value, moved code in own function]
Signed-off-by: NLaurentiu Tudor <Laurentiu.Tudor@freescale.com>
Acked-by: NScott Wood <scotttwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The register is not currently used in the base kernel
but will be in a forthcoming kvm patch.
Signed-off-by: NLaurentiu Tudor <Laurentiu.Tudor@freescale.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We need to properly identify whether a hugepage is an explicit or
a transparent hugepage in follow_huge_addr(). We used to depend
on hugepage shift argument to do that. But in some case that can
result in wrong results. For ex:

On finding a transparent hugepage we set hugepage shift to PMD_SHIFT.
But we can end up clearing the thp pte, via pmdp_huge_get_and_clear.
We do prevent reusing the pfn page via the usage of
kick_all_cpus_sync(). But that happens after we updated the pte to 0.
Hence in follow_huge_addr() we can find hugepage shift set, but transparent
huge page check fail for a thp pte.

NOTE: We fixed a variant of this race against thp split in commit
691e95fd
("powerpc/mm/thp: Make page table walk safe against thp split/collapse")

Without this patch, we may hit the BUG_ON(flags & FOLL_GET) in
follow_page_mask occasionally.

In the long term, we may want to switch ppc64 64k page size config to
enable CONFIG_ARCH_WANT_GENERAL_HUGETLB
Reported-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

After commit e2b3d202
("powerpc: Switch 16GB and 16MB explicit hugepages to a
different page table format"), we don't need to support
is_hugepd() for 64K page size.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This avoid errors like

        unsigned int usize = 1 << 30;
        int size = 1 << 30;
        unsigned long addr = 64UL << 30 ;

        value = _ALIGN_DOWN(addr, usize); -> 0
        value = _ALIGN_DOWN(addr, size);  -> 0x1000000000
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

native_hpte_clear() is called in real mode from two places:
- Early in boot during htab initialisation if firmware assisted dump is
  active.
- Late in the kexec path.

In both contexts there is no need to disable interrupts are they are
already disabled. Furthermore, locking around the tlbie() is only required
for pre POWER5 hardware.

On POWER5 or newer hardware concurrent tlbie()s work as expected and on pre
POWER5 hardware concurrent tlbie()s could result in deadlock. This code
would only be executed at crashdump time, during which all bets are off,
concurrent tlbie()s are unlikely and taking locks is unsafe therefore the
best course of action is to simply do nothing. Concurrent tlbie()s are not
possible in the first case as secondary CPUs have not come up yet.
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

For some reason, only the little-endian flavor of
powerpc provided the zero_bytemask() implementation.
Reported-by: NMichal Sojka <sojkam1@fel.cvut.cz>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NChris Metcalf <cmetcalf@ezchip.com>

arch/tile added word-at-a-time.h after the patch that added generic-y
entries; the generic-y entry is now stale.

arch/h8300 is newer than the generic-y patch for word-at-a-time.h,
and needs a generic-y entry.

arch/powerpc seems to have gotten a generic-y entry by mistake in
the first patch; this change removes it.
Signed-off-by: NChris Metcalf <cmetcalf@ezchip.com>

During the MSI bitmap test on boot kmemleak spews the following trace:

unreferenced object 0xc00000016e86c900 (size 64):
    comm "swapper/0", pid 1, jiffies 4294893173 (age 518.024s)
    hex dump (first 32 bytes):
	00 00 01 ff 7f ff 7f 37 00 00 00 00 00 00 00 00
	.......7........
	ff ff ff ff ff ff ff ff 01 ff ff ff ff
	ff ff ff
	................
	backtrace:
	[<c00000000003eebc>] .zalloc_maybe_bootmem+0x3c/0x380
	[<c000000000042d6c>] .msi_bitmap_alloc+0x3c/0xb0
	[<c000000000a9aff8>] .msi_bitmap_selftest+0x30/0x2b4
	[<c0000000000090f4>] .do_one_initcall+0xd4/0x270
	[<c000000000a8e250>] .kernel_init_freeable+0x1a0/0x280
	[<c000000000009b5c>] .kernel_init+0x1c/0x120
	[<c000000000007fbc>] .ret_from_kernel_thread+0x58/0x9c

Add a flag to msi_bitmap for tracking allocations from slab and memblock
so we can properly free/handle memory in msi_bitmap_free().
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
[mpe: Reword changelog & use bitmap_from_slab in the if]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This add helper virt_to_pfn and remove the opencoded usage of the
same.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We observed some performance degradation on s390x with dynamic
halt polling. Until we can provide a proper fix, let's enable
halt_poll_ns as default only for supported architectures.

Architectures are now free to set their own halt_poll_ns
default value.
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The selftest passes on 64-bit LE & BE, and 32-bit.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.

Remove the argument.

Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>

This new statistic can help diagnosing VCPUs that, for any reason,
trigger bad behavior of halt_poll_ns autotuning.

For example, say halt_poll_ns = 480000, and wakeups are spaced exactly
like 479us, 481us, 479us, 481us. Then KVM always fails polling and wastes
10+20+40+80+160+320+480 = 1110 microseconds out of every
479+481+479+481+479+481+479 = 3359 microseconds. The VCPU then
is consuming about 30% more CPU than it would use without
polling.  This would show as an abnormally high number of
attempted polling compared to the successful polls.

Acked-by: Christian Borntraeger <borntraeger@de.ibm.com<
Reviewed-by: NDavid Matlack <dmatlack@google.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Almost everyone implements dma_set_mask the same way, although some time
that's hidden in ->set_dma_mask methods.

This patch consolidates those into a common implementation that either
calls ->set_dma_mask if present or otherwise uses the default
implementation.  Some architectures used to only call ->set_dma_mask
after the initial checks, and those instance have been fixed to do the
full work.  h8300 implemented dma_set_mask bogusly as a no-ops and has
been fixed.

Unfortunately some architectures overload unrelated semantics like changing
the dma_ops into it so we still need to allow for an architecture override
for now.

[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most architectures just call into ->dma_supported, but some also return 1
if the method is not present, or 0 if no dma ops are present (although
that should never happeb). Consolidate this more broad version into
common code.

Also fix h8300 which inorrectly always returned 0, which would have been
a problem if it's dma_set_mask implementation wasn't a similarly buggy
noop.

As a few architectures have much more elaborate implementations, we
still allow for arch overrides.

[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently there are three valid implementations of dma_mapping_error:

 (1) call ->mapping_error
 (2) check for a hardcoded error code
 (3) always return 0

This patch provides a common implementation that calls ->mapping_error
if present, then checks for DMA_ERROR_CODE if defined or otherwise
returns 0.

[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most architectures do not support non-coherent allocations and either
define dma_{alloc,free}_noncoherent to their coherent versions or stub
them out.

Openrisc uses dma_{alloc,free}_attrs to implement them, and only Mips
implements them directly.

This patch moves the Openrisc version to common code, and handles the
DMA_ATTR_NON_CONSISTENT case in the mips dma_map_ops instance.

Note that actual non-coherent allocations require a dma_cache_sync
implementation, so if non-coherent allocations didn't work on
an architecture before this patch they still won't work after it.

[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 2009 we have a nice asm-generic header implementing lots of DMA API
functions for architectures using struct dma_map_ops, but unfortunately
it's still missing a lot of APIs that all architectures still have to
duplicate.

This series consolidates the remaining functions, although we still need
arch opt outs for two of them as a few architectures have very
non-standard implementations.

This patch (of 5):

The coherent DMA allocator works the same over all architectures supporting
dma_map operations.

This patch consolidates them and converges the minor differences:

 - the debug_dma helpers are now called from all architectures, including
   those that were previously missing them
 - dma_alloc_from_coherent and dma_release_from_coherent are now always
   called from the generic alloc/free routines instead of the ops
   dma-mapping-common.h always includes dma-coherent.h to get the defintions
   for them, or the stubs if the architecture doesn't support this feature
 - checks for ->alloc / ->free presence are removed.  There is only one
   magic instead of dma_map_ops without them (mic_dma_ops) and that one
   is x86 only anyway.

Besides that only x86 needs special treatment to replace a default devices
if none is passed and tweak the gfp_flags.  An optional arch hook is provided
for that.

[linux@roeck-us.net: fix build]
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The selftest passes on 64-bit LE and BE.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The size of the Problem State Priority Boost Register is only
32 bits, but the kvm_vcpu_arch->pspb variable is declared as
"ulong", ie. 64-bit. However, the assembler code accesses this
variable with 32-bit accesses, and the KVM_REG_PPC_PSPB macro
is defined with SIZE_U32, too, so that the current code is
broken on big endian hosts: kvmppc_get_one_reg_hv() will only
return zero for this register since it is using the wrong half
of the pspb variable. Let's fix this problem by adjusting the
size of the pspb field in the kvm_vcpu_arch structure.
Signed-off-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>