Add the Cisco Powertv cable settop box to the MIPS tree. This platform is
based on a MIPS 24Kc processor with various devices integrated on the same
ASIC. There are multiple models of this box, with differing configuration
but the same kernel runs across the product line.
Signed-off-by: NDavid VomLehn <dvomlehn@cisco.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/132/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds support for the Texas Instruments AR7 System-on-a-Chip.
It supports the TNETD7100, 7200 and 7300 versions of the SoC.
Signed-off-by: NMatteo Croce <matteo@openwrt.org>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NEugene Konev <ejka@openwrt.org>
Signed-off-by: NNicolas Thill <nico@openwrt.org>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch includes a number of small changes for integrating the
AT91SAM9261 and AT91SAM0260 support.

      * Can only select support for one AT91 processor at a time.
      * Remove most of the remaining static memory mapping for the
        AT91RM9200.
      * Reserve 1Mb of memory below the IO for mapping the internal SRAM
        and any custom board-specific devices (ie, FPGA).
      * The SAM9260 has more serial ports, so increase the maximum to 7.
      * Define the standard chipselect addresses, and define other
        addresses relative to those.
      * CLOCK_TICK_RATE is different on the SAM926x's.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch maps the AT91RM9200's internal SRAM into the virtual memory
address space - just below the internal peripheral registers.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from SAN People

Following changes were made to clock.c:

1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.

Otherwise it's the same as the previous patch.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rationalise hardware.h include.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!