Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI Express Port Bus driver. This avoids unnecessary serarch
in PCI configuration space.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove unused port_data variable left over from the MCH hotplug quirk
cleanup.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.

Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.

The re-running of this fixup after pci hotplug happens below these
devices is totally bogus.  All of the state we change is pure software
state and we don't change the hardware at all.  Which means hotplug on
the lower devices doesn't have a chance to change this state.  So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.

I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.


Cc: linux-pci@vger.kernel.org
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCIe port driver calls pci_enable_device when registering
ports, but never calls pci_disable_device during removal.
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Implement pm object for the PCI Express port driver in order to use
the new power management framework and reduce the code size.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pcie_port_device_remove currently calls the remove method of port
drivers twice.  Ouch!

We are calling device_for_each_child multiple times for no apparent
reason.

So make it simple. Place put_device and device_unregister into
remove_iter, and throw out the rest.  Only call device_for_each_child
once.

The code is simpler and actually works!
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If MSI-X interrupt mode is used by the PCI Express port driver, too
many vectors are allocated and it is not ensured that the right
vectors will be used for the right services.  Namely, the PCI Express
specification states that both PCI Express native PME and PCI Express
hotplug will always use the same MSI or MSI-X message for signalling
interrupts, which implies that the same vector will be used by both
of them.  Also, the VC service does not use interrupts at all.
Moreover, is not clear which of the vectors allocated by
pci_enable_msix() in the current code will be used for PME and
hotplug and which of them will be used for AER if all of these
services are configured.

For these reasons, rework the allocation of interrupts for PCI
Express ports so that if MSI-X are enabled, the right vectors will be
used for the right purposes.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCI Express port driver uses 'struct pcie_port_service_id' for
matching port service devices and drivers, but this structure
contains fields that duplicate information from the port device
itself (vendor, device, subvendor, subdevice) and fields that are not
used by any existing port service driver (class, class_mask,
drvier_data).  Also, both existing port service drivers (AER and
PCIe HP) don't even use the vendor and device fields for device
matching.  Therefore 'struct pcie_port_service_id' can be removed
altogether and the only useful members of it (port_type, service) can
be introduced directly into the port service device and port service
driver structures.  That simplifies the code quite a bit and reduces
its size.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The second argument of the ->probe() callback in
struct pcie_port_service_driver is unnecessary and never used.
Remove it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCI Express port driver calls pci_enable_device() before setting
up interrupts, which is wrong, because if there is an interrupt pin
configured for the port, pci_enable_device() will likely set up an
interrupt link for it.  However, this shouldn't be done if either
MSI or MSI-X interrupt mode is chosen for the port.

The solution is to call pci_enable_device() after setting up
interrupts, because in that case the interrupt link won't be set up
if MSI or MSI-X are enabled.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCI Express port driver should not attempt to register service
devices that require the ability to generate interrupts if generating
interrupts is not possible.  Namely, if the port has no interrupt pin
configured and we cannot set up MSI or MSI-X for it, there is no way
it can generate interrupts and in such a case the port services that
rely on interrupts (PME, PCIe HP, AER) should not be enabled for it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

PCI Express port driver extension, as defined by struct
pcie_port_device_ext in portdrv.h, is allocated and initialized, but
never used (it also is never freed).  Extend it to hold the PCI Express
port type as well as the port interrupt mode, change its name and use it
to simplify the code in portdrv_core.c .

Additionally, remove the redundant interrupt_mode member of struct
pcie_device defined in include/linux/pcieport_if.h .
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add kerneldoc comments to the reamining functions in
drivers/pci/pcie/portdrv_core.c .
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Rearrange code in drivers/pci/pcie/portdrv_bus.c and
drivers/pci/pcie/portdrv_core.c so that related functions and data
structures are closer together.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There is a problem with the suspend and resume of PCI Express port
service devices that the ->suspend() and ->resume() routines of each
service device are called twice in each suspend-resume cycle, which
is obviously wrong.

The scenario is that first, the PCI Express port driver calls
suspend and resume routines of each port service driver from its
pcie_portdrv_suspend() and pcie_portdrv_resume() callbacks,
respectively (which is correct), and second, the pcie_port_bus_type
driver calls them from its ->suspend() and ->resume() callbacks
(which is not correct, because it doesn't happen at the right time).

The solution is to remove the ->suspend() and ->resume() callbacks
from pcie_port_bus_type and the associated functions.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add kerneldoc comments to some functions in
drivers/pci/pcie/portdrv_core.c, since the code in there is not
easy to follow without any additional description.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

These printks don't contain enough information to be useful.  I think it
would be more useful to have a message when a service driver binds to a
root port.  That could contain the service type, the interrupt mode and
IRQ, etc.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".

To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.

We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove some open coded (and buggy) versions of pci_find_ext_capability
in favor of the real routine in the PCI core.
Tested-by: NTomasz Czernecki <czernecki@gmail.com>
Acked-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Convert printks to use dev_printk().
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Native PME is capability of root port or root complex event collector.
It's not determined by PCI PME capability.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

__must_check goes on the declaration, not the definition.

Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Have pcie_port_bus_register() notice and return errors.
Mark it __must_check so that its caller(s) must check its return value.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this patch converts drivers/pci to kzalloc usage.
Compile tested with allyes config.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bus_id string must be unique for all devices of that bus in the
system, not just for devices with the same parent - otherwise multiple
symlinks with identical names appear in /sys/bus/pci_express/devices.
Signed-off-by: NSergey Vlasov <vsu@altlinux.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.

In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch.  This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other.  So if any
hunk rejects or gets in the way of other patches, just drop it.  My scripts
will pick it up again in the next round.
Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In PM v1, all devices were called at SUSPEND_DISABLE level.  Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level.  However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.

Since this is obsolete infrastructure which is no longer necessary,
we can remove it.  Here's an (untested) patch to do exactly that.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Few more u32 vs. pm_message_t fixes.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch, is based on kernel 2.6.12, provides a fix for PCIe
port bus driver suspend/resume.
Signed-off-by: NT. Long Nguyen <tom.l.nguyen@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On Friday, March 25, 2005 8:47 PM Greg KH wrote:
>Here's a fix for pci express.  For some reason I don't think they are
>using the driver model properly here, but I could be wrong...

Thanks for making the changes. However, changes in functions:
void pcie_port_device_remove(struct pci_dev *dev) and
static int remove_iter(struct device *dev, void *data)
are not correct. Please use the patch, which is based on kernel
2.6.12-rc1, below for a fix for these.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes drivers/pci (mostly pcie stuff).
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!