Add the ability to inject IOMMU faults. We enable this per device
via a fail_iommu sysfs property, similar to fault injection on other
subsystems.

An example:

...
0003:01:00.1 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 02)

To inject one error to this device:

echo 1 > /sys/bus/pci/devices/0003:01:00.1/fail_iommu
echo 1 > /sys/kernel/debug/fail_iommu/probability
echo 1 > /sys/kernel/debug/fail_iommu/times

As feared, the first failure injected on the be3 results in an
unrecoverable error, taking down both functions of the card
permanently:

be2net 0003:01:00.1: Unrecoverable error in the card
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The DMA API debug code has hooks to verify all DMA entries have been
freed at time of hot unplug. We need to call dma_debug_add_bus for
this to work.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The logic to choose whether to use the SIAR or get the information
out of pt_regs is going to get more complicated, so do it once in
perf_read_regs.

We overload regs->result which is gross but we are already doing it
with regs->dsisr.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Some macros use RA where when RA=R0 the values is 0, so make this
the enforced mnemonic in the macro.

Idea suggested by Andreas Schwab.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

R0 is special since it'll be 0.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Enforce the use of R0-R31 in macros where possible now we have all the
fixes in.

R0-R31 macros are removed here so that can't be used anymore.  They
should not be defined anywhere.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Now have ___PPC_RA/B/S/T we can use it in some places.  These are
places where we can't use the existing defines which will soon enforce
R0-R31 usage.

The macros being changed here are being used in inline asm, which
can't convert to enforce the R0-R31 usage.

bpf_jit uses a mix of both generated and non-generated with the same
code, so just convert all these to use the ___PPC_R versions which
won't enforce R usage later.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

These are currently the same as __PPC_RA/B/S/T but we'll wrap them
soon.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to do this so we can enforce the name of a and b in called
macros PPC_RA/B later.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

mtocrf define is just a wrapper around the real instructions so we can
just use real register names here (ie. lower case).

Also remove braces in macro so this is possible.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Move this duplicated definition to ppc_asm.h and remove the
braces which prevent the use of %rN register names
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Merge the defines of VCPU_GPR from different places.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Merge the defines of STACKFRAMESIZE, STK_REG, STK_PARAM from different
places.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

move lbz/stbciz to ppc-opcode.h.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Now all the fixes are in place, let's rock-n-roll!
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The assembler doesn't take %r0 register arguments in braces, so remove them.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We are going to use these later and convert r0 to %r0 etc.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There was a typo, checking for CONFIG_TRACE_IRQFLAG instead of
CONFIG_TRACE_IRQFLAGS causing some useful debug code to not be
built

This in turns causes a build error on BookE 64-bit due to incorrect
semicolons at the end of a couple of macros, so let's fix that too
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org [v3.4]

Looks like we still have issues with pSeries and Cell idle code
vs. the lazy irq state. In fact, the reset fixes that went upstream
are exposing the problem more by causing BUG_ON() to trigger (which
this patch turns into a WARN_ON instead).

We need to be careful when using a variant of low power state that
has the side effect of turning interrupts back on, to properly set
all the SW & lazy state to look as if everything is enabled before
we enter the low power state with MSR:EE off as we will return with
MSR:EE on. If not, we have a discrepancy of state which can cause
things to go very wrong later on.

This patch moves the logic into a helper and uses it from the
pseries and cell idle code. The power4/970 idle code already got
things right (in assembly even !) so I'm not touching it. The power7
"bare metal" idle code is subtly different and correct. Remains PA6T
and some hypervisor based Cell platforms which have questionable
code in there, but they are mostly dead platforms so I'll fix them
when I manage to get final answers from the respective maintainers
about how the low power state actually works on them.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org [v3.4]

The array of names in hugetlbpage.c no longer exists.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

At the moment all queues in a multiqueue adapter will serialise
against the IOMMU table lock. This is proving to be a big issue,
especially with 10Gbit ethernet.

This patch creates 4 pools and tries to spread the load across
them. If the table is under 1GB in size we revert back to the
original behaviour of 1 pool and 1 largealloc pool.

We create a hash to map CPUs to pools. Since we prefer interrupts to
be affinitised to primary CPUs, without some form of hashing we are
very likely to end up using the same pool. As an example, POWER7
has 4 way SMT and with 4 pools all primary threads will map to the
same pool.

The largealloc pool is reduced from 1/2 to 1/4 of the space to
partially offset the overhead of breaking the table up into pools.

Some performance numbers were obtained with a Chelsio T3 adapter on
two POWER7 boxes, running a 100 session TCP round robin test.

Performance improved 69% with this patch applied.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

irq_entry, irq_exit, timer_interrupt_entry and timer_interrupt_exit
all do the same thing so use DECLARE_EVENT_CLASS to avoid duplicating
everything 4 times.

This saves quite a lot of space in both instruction text and data:

   text    data     bss     dec     hex filename
   9265   19622      16   28903    70e7 arch/powerpc/kernel/irq.o
   6817   19019      16   25852    64fc arch/powerpc/kernel/irq.o
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The following patch is to remove the pseries_notify_add_cpu() call
and replace it by a hot plug notifier.

This would prevent cpuidle resources being released and allocated each
time cpu comes online on pseries.

The earlier design was causing a lockdep problem
in start_secondary as reported on this thread
	-https://lkml.org/lkml/2012/5/17/2

This applies on 3.4-rc7
Signed-off-by: NDeepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For ftrace to use the patch_instruction code, it needs to check for
faults on write. Ftrace updates code all over the kernel, and we need to
know if code is updated or not due to protections that are placed on
some portions of the kernel. If ftrace does not detect a fault, it will
error later on, and it will be much more difficult to find the problem.

By changing patch_instruction() to detect faults, then ftrace will be
able to make use of it too.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit f948501b ("Make hard_irq_disable() actually hard-disable
interrupts") caused check_and_cede_processor to stop working.
->irq_happened will never be zero right after a hard_irq_disable
so the compiler removes the call to cede_processor completely.

The bug was introduced back in the lazy interrupt handling rework
of 3.4 but was hidden until recently because hard_irq_disable did
nothing.

This issue will eventually appear in 3.4 stable since the
hard_irq_disable fix is marked stable, so mark this one for stable
too.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

At present, hard_irq_disable() does nothing on powerpc because of
this code in include/linux/interrupt.h:

    #ifndef hard_irq_disable
    #define hard_irq_disable()      do { } while(0)
    #endif

So we need to make our hard_irq_disable be a macro.  It was previously
a macro until commit 7230c564 ("powerpc: Rework lazy-interrupt
handling") changed it to a static inline function.

Cc: stable@vger.kernel.org
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
--
 arch/powerpc/include/asm/hw_irq.h |    3 +++
 1 file changed, 3 insertions(+)

commit e57f93cc (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

helpers parallel to set_restore_sigmask(), used in the next commits
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This is much the same as for SPARC except that we can do the find_zero()
function more efficiently using the count-leading-zeroes instructions.
Tested on 32-bit and 64-bit PowerPC.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

--
Signed-off-by: NAnshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Historical prepare_to_copy() is mostly a no-op, duplicated for majority of
the architectures and the rest following the x86 model of flushing the extended
register state like fpu there.

Remove it and use the arch_dup_task_struct() instead.
Suggested-by: NOleg Nesterov <oleg@redhat.com>
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-1-git-send-email-suresh.b.siddha@intel.comAcked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

The code forgot to scramble the VSIDs the way we normally do
and was basically using the "proto VSID" directly with the MMU.

This means that in practice, KVM used random VSIDs that could
collide with segments used by other user space programs.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
[agraf: simplify ppc32 case]
Signed-off-by: NAlexander Graf <agraf@suse.de>

Add support for the Platform Facilities Option (PFO) to the VIO bus.
These devices have a separate root node in OpenFirmware which
requires additional parsing to map into the existing VIO device
structure fields. This adds the interface for PFO device drivers to
make synchronous hypervisor calls.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NKent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This adds an update notifier mechanism for changes to properties in the
device tree.  One use of this would be a device driver that needs to act
on changes to it's properties in the device tree after a live migration
or a dynamic activation that is triggered by updates to ofdt properties.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NKent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The Platform Facilities Option (PFO) adds several new h_calls and
more return codes.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NKent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Rather than requiring architectures that use gpiolib but don't have any
need to define anything custom to copy an asm/gpio.h provide a Kconfig
symbol which architectures must select in order to include gpio.h and
for other architectures just provide the trivial implementation directly.

This makes it much easier to do gpiolib updates and is also a step towards
making gpiolib APIs available on every architecture.

For architectures with existing boilerplate code leave a stub header in
place which warns on direct inclusion of asm/gpio.h and includes
linux/gpio.h to catch code that's doing this.  Direct inclusion of
asm/gpio.h has long been deprecated.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJonas Bonn <jonas@southpole.se>
Acked-by: NTony Luck <tony.luck@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>