ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.

To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:

[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95

Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.
Reported-by: NZaki Bakar <zaki.bm@gmail.com>
Tested-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The mgmt_rx event structure has been expanded.
Since the structure header is expanded the payload
(i.e. mgmt frame) is shifted by a few bytes. This
needs to be taken into account in order to support
both old and new firmware.

This introduces a fw_features to keep track of any
FW-related ABI/behaviour changes.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This implements a limited subset of what can be
reported in the survey dump.

This can be used for assessing approximate channel
load, e.g. for automatic channel selection.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Until now ath10k assumed 3 spatial streams.
However some devices support only 2 spatial
streams.

This patch improves performance on devices that
don't support 3 spatial streams.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Restart the hardware if FW crashes.

If FW crashes during recovery we leave the
hardware in a "wedged" state to avoid recursive
recoveries.

When in "wedged" state userspace may bring
interfaces down (to issue stop()) and then bring
one interface (to issue start()) to reload
hardware manually.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Different FW versions may provide different
functions thus mean different hw capabilities
advertised to mac80211.

It is safe to swap firmware files on disk during
driver/device runtime without worries.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Split up fw-related and hw-related suspension code.

Although we don't advertise WoW support to
mac80211 yet it's useful to keep the code in
suspend/resume hooks.

At this point there's no need to keep pci pm ops.
In case of WoW mac80211 calls ath10k_suspend()
which should take care of entering low-power mode.
In case WoW is not available mac80211 will go
through regular interface teradown and use start/stop.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Regulatory domain notification hook can be called
regardless of the hw state (i.e. before start
mac80211 callback).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enables code reuse for proper hw reconfiguration
that is in turn required for proper
suspend/hibernation/wowlan support.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This reduces number of allocations and simplifies
memory managemnt.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This reduces number of allocations and simplifies
memory managemnt.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It serves no purpose.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Here's a new mac80211 driver for Qualcomm Atheros 802.11ac QCA98xx devices.
A major difference from ath9k is that there's now a firmware and
that's why we had to implement a new driver.

The wiki page for the driver is:

http://wireless.kernel.org/en/users/Drivers/ath10k

The driver has had many authors, they are listed here alphabetically:

Bartosz Markowski <bartosz.markowski@tieto.com>
Janusz Dziedzic <janusz.dziedzic@tieto.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Marek Kwaczynski <marek.kwaczynski@tieto.com>
Marek Puzyniak <marek.puzyniak@tieto.com>
Michal Kazior <michal.kazior@tieto.com>
Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>