- 03 2月, 2007 1 次提交
-
-
由 Len Brown 提交于
...by disabling CONFIG_ACPI when CONFIG_X86_NUMAQ=y otherwise arch/i386/pci/Makefile forgets that it needs to build acpi.o drivers/built-in.o: In function `acpi_pci_root_add': pci_root.c:(.text+0x45ec4): undefined reference to `pci_acpi_scan_root' Signed-off-by: NLen Brown <len.brown@intel.com>
-
- 30 1月, 2007 2 次提交
-
-
由 Len Brown 提交于
Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Robert P. J. Day 提交于
-#ifdef CONFIG_ACPI_DEBUG_OUTPUT +#ifdef ACPI_DEBUG_OUTPUT As the former doesn't exist. Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com> Signed-off-by: NLen Brown <len.brown@intel.com>
-
- 27 1月, 2007 22 次提交
-
-
由 David Woodhouse 提交于
On the Maple board, the AMD8111 IDE is in legacy mode... except that it appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by the architecture's "pci_get_legacy_ide_irq()" function, but in libata we just hard-code the numbers 14 and 15. This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as appropriate, having added a pci_dev argument to the ATA_{PRIM,SECOND}ARY_IRQ macros. There's probably a better way to do this -- especially if we observe that the _only_ case in which this seemingly-generic "pci_get_legacy_ide_irq()" function returns anything other than 14 and 15 for primary and secondary respectively is the case of the AMD8111 on the Maple board -- couldn't we handle that with a special case in the pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into native mode during early boot and assign resources properly? Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
Before hardreset, ahci initialized stat part of received FIS area to 0xff to wait for the first D2H Reg FIS which would change the value to device ready state. This used to work but now libata considers status value of 0xff as device not present making this wait prone to failure. This patch makes ahci use 0x80 for the wait stat value instead of 0xff to fix the above problem. Signed-off-by: NTejun Heo <htejun@gmail.com> drivers/ata/ahci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
Call ata_bmdma_irq_clear() directly instead of through ap->ops->irq_clear() according to libata style guideline. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
Fix endianness in spurious interrupt message. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Matt Domsch 提交于
Fix race when deleting an EFI variable and issuing another EFI command on the same variable. The removal of the variable from the efivars_list should be done in efivar_delete and not delayed until the kobject release. Furthermore, remove the item from the list at module unload time, and use list_for_each_entry_safe() rather than list_for_each_safe() for readability. Tested on ia64. Signed-off-by: NPrarit Bhargava <prarit@redhat.com> Signed-off-by: NMatt Domsch <Matt_Domsch@dell.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 NeilBrown 提交于
raid5_mergeable_bvec tries to ensure that raid5 never sees a read request that does not fit within just one chunk. However as we must always accept a single-page read, that is not always possible. So when "in_chunk_boundary" fails, it might be unusual, but it is not a problem and printing a message every time is a bad idea. Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 NeilBrown 提交于
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held, it is possible for a deadlock to eventuate. This happens if the array was marked 'clean', and the memalloc triggers a write-out to the md device. For the writeout to succeed, the array must be marked 'dirty', and that requires getting the mddev_lock. So, before attempting a GFP_KERNEL allocation while holding the lock, make sure the array is marked 'dirty' (unless it is currently read-only). Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mike Frysinger 提交于
rtc_sysfs_add_device is needed even after dev initialization, so drop __devinit. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Acked-by: NAlessandro Zummo <a.zummo@towertech.it> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jun'ichi Nomura 提交于
Allow noflush suspend/resume of device-mapper device only for the case where the device size is unchanged. Otherwise, dm-multipath devices can stall when resumed if noflush was used when suspending them, all paths have failed and queue_if_no_path is set. Explanation: 1. Something is doing fsync() on the block dev, holding inode->i_sem 2. The fsync write is blocked by all-paths-down and queue_if_no_path 3. Someone requests to suspend the dm device with noflush. Pending writes are left in queue. 4. In the middle of dm_resume(), __bind() tries to get inode->i_sem to do __set_size() and waits forever. 'noflush suspend' is a new device-mapper feature introduced in early 2.6.20. So I hope the fix being included before 2.6.20 is released. Example of reproducer: 1. Create a multipath device by dmsetup 2. Fail all paths during mkfs 3. Do dmsetup suspend --noflush and load new map with healthy paths 4. Do dmsetup resume Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com> Acked-by: NAlasdair G Kergon <agk@redhat.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 NeilBrown 提交于
In most cases we check the size of the bitmap file before reading data from it. However when reading the superblock, we always read the first PAGE_SIZE bytes, which might not always be appropriate. So limit that read to the size of the file if appropriate. Also, we get the count of available bytes wrong in one place, so that too can read past the end of the file. Cc: "yang yin" <yinyang801120@gmail.com> Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 NeilBrown 提交于
Now that we sometimes step the array events count backwards (when transitioning dirty->clean where nothing else interesting has happened - so that we don't need to write to spares all the time), it is possible for the event count to return to zero, which is potentially confusing and triggers and MD_BUG. We could possibly remove the MD_BUG, but is just as easy, and probably safer, to make sure we never return to zero. Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 NeilBrown 提交于
When 'repair' finds a block that is different one the various parts of the mirror. it is meant to write a chosen good version to the others. However it currently writes out the original data to each. The memcpy to make all the data the same is missing. Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Tilman Schmidt 提交于
Fix several flaws in the error handling of the Siemens Gigaset ISDN driver, including one that would cause an Oops when connecting more than one device of the same type. Signed-off-by: NTilman Schmidt <tilman@imap.cc> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Ingo Molnar 提交于
Recently cpufreq support on my laptop (Lenovo T60) broke completely: when it's plugged into AC it would never go higher than 1 GHz - neither 1.3 GHz nor 1.83 GHz is possible - no matter which governor (userspace, speed or ondemand) is used. After some cpufreq debugging i tracked the regression back to the following (totally correct) bug-fix commit: commit 0916bd3e Author: Dave Jones <davej@redhat.com> Date: Wed Nov 22 20:42:01 2006 -0500 [PATCH] Correct bound checking from the value returned from _PPC method. This bugfix, which makes other laptops work, made a previously hidden (BIOS) bug visible on my laptop. The bug is the following: if the _PPC (Performance Present Capabilities) optional ACPI object is queried /after/ bootup then the BIOS reports an incorrect value of '2'. My laptop (Lenovo T60) has the following performance states supported: 0: 1833000 1: 1333000 2: 1000000 Per ACPI specification, a _PPC value of '0' means that all 3 performance states are usable. A _PPC value of '1' means states 1 .. 2 are usable, a value of '2' means only state '2' (slowest) is usable. now, the _PPC object is optional, and it also comes with notification. Furthermore, when a CPU object is initialized, the _PPC object is initialized as well. So the following evaluation of the _PPC object is superfluous: [<c028ba5f>] acpi_processor_get_platform_limit+0xa1/0xaf [<c028c040>] acpi_processor_register_performance+0x3b9/0x3ef [<c0111a85>] acpi_cpufreq_cpu_init+0xb7/0x596 [<c03dab74>] cpufreq_add_dev+0x160/0x4a8 [<c02bed90>] sysdev_driver_register+0x5a/0xa0 [<c03d9c4c>] cpufreq_register_driver+0xb4/0x176 [<c068ac08>] acpi_cpufreq_init+0xe5/0xeb [<c010056e>] init+0x14f/0x3dd And this is the point where my laptop's BIOS returns the incorrect value of '2'. Note that it has not sent any notification event, so the value is probably not really intentional (possibly spurious), and Windows likely doesnt query it after bootup either. Maybe the value is kept at '2' normally, and is only set to the real value when a true asynchronous event (such as AC plug event, battery switch, etc.) occurs. So i /think/ this is a grey area of the ACPI spec: per the letter of the spec the _PPC value only changes when notified, so there's no reason to query it after the system has booted up. So in my opinion the best (and most compatible) strategy would be to do the change below, and to not evaluate the _PPC object in the acpi_processor_get_performance_info() call, but only evaluate it if _PPC is present during CPU object init, or if it's notified during an asynchronous event. This change is more permissive than the previous logic, so it definitely shouldnt break any existing system. This also happens to fix my laptop, which is merrily chugging along at 1.83 GHz now. Yay! Signed-off-by: NIngo Molnar <mingo@elte.hu> Cc: Dave Jones <davej@redhat.com> Acked-by: NLen Brown <lenb@kernel.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Atsushi Nemoto 提交于
If a SPI master device exists, udev (udevtrigger) causes kernel crash, due to wrong kobj pointer in kobject_uevent_env(). This problem was not in 2.6.19. The backtrace (on MIPS) was: [<8024db6c>] kobject_uevent_env+0x54c/0x5e8 [<802a8264>] store_uevent+0x1c/0x3c (in drivers/class.c) [<801cb14c>] subsys_attr_store+0x2c/0x50 [<801cb80c>] flush_write_buffer+0x38/0x5c [<801cb900>] sysfs_write_file+0xd0/0x190 [<80181444>] vfs_write+0xc4/0x1a0 [<80181cdc>] sys_write+0x54/0xa0 [<8010dae4>] stack_done+0x20/0x3c flush_write_buffer() passes kobject of spi_master_class.subsys to subsys_addr_store(), then subsys_addr_store() passes a pointer to a struct subsystem to store_uevent() which expects a pointer to a struct class_device. The problem seems subsys_attr_store() called instead of class_device_attr_store(). This mismatch was caused by commit 3bd0f694, which overrides kset of master class. This made spi_master_class.subsys.kset.ktype NULL so subsys_sysfs_ops is used instead of class_dev_sysfs_ops. The commit was to fix spi_busnum_to_master(). Here is a patch fixes this function in other way, just searching children list of class_device. Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Justin Clacherty 提交于
Currently the spi mode can be set to the wrong mode if you are switching from any mode other than mode 0. This is because the mode is set using a bitwise or on uncleared bits. The following patch clears the mode bits before setting the new mode. I've also modified it to use the appropriate defines from pxa-regs.h for readability. Signed-off-by: NJustin Clacherty <justin@redfish-group.com> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Ben Dooks 提交于
It turns out that the spi chipselect was not being passed to the set_cs routine if one was specified in the platform data. As part of the fix, change to using a set_cs field in the controller state, and put a default gpio routine in if the data passed does not specify it. Also remove the //#define DEBUG Signed-off-by: NBen Dooks <ben-linux@fluff.org> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Joerg Roedel 提交于
This patch implements forwarding of SHUTDOWN intercepts from the guest on to userspace on AMD SVM. A SHUTDOWN event occurs when the guest produces a triple fault (e.g. on reboot). This also fixes the bug that a guest reboot actually causes a host reboot under some circumstances. Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com> Signed-off-by: NAvi Kivity <avi@qumranet.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Avi Kivity 提交于
With the recent guest page fault change, we perform access checks on our own instead of relying on the cpu. This means we have to perform the nx checks as well. Software like the google toolbar on windows appears to rely on this somehow. Signed-off-by: NAvi Kivity <avi@qumranet.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Avi Kivity 提交于
Check pte permission bits in walk_addr(), instead of scattering the checks all over the code. This has the following benefits: 1. We no longer set the accessed bit for accessed which fail permission checks. 2. Setting the accessed bit is simplified. 3. Under some circumstances, we used to pretend a page fault was fixed when it would actually fail the access checks. This caused an unnecessary vmexit. 4. The error code for guest page faults is now correct. The fix helps netbsd further along booting, and allows kvm to pass the new mmu testsuite. Signed-off-by: NAvi Kivity <avi@qumranet.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Avi Kivity 提交于
This allows netbsd 3.1 i386 to get further along installing. Signed-off-by: NAvi Kivity <avi@qumranet.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Leonard Norrgard 提交于
There's an obvious typo in svm_{get,set}_idt, causing it to access the ldt instead. Because these functions are only called for save/load on AMD, the bug does not impact normal operation. With the fix, save/load works as expected on AMD hosts. Signed-off-by: NUri Lublin <uril@qumranet.com> Signed-off-by: NAvi Kivity <avi@qumranet.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 26 1月, 2007 5 次提交
-
-
由 Michael Chan 提交于
On the 5709, we need to add the proper offset to calculate the shared memory base address of the 2nd port correctly. Otherwise, the 2nd port's MAC address and other information will be the same as the 1st port. Update version to 1.5.4. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alan 提交于
Fixes bogus accesses to ports 0-15 with a non DMA capable controller. This I think should go in for 2.6.20 Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
Some uli controllers have stuck SIMPLEX bit which can't be cleared with ata_pci_clear_simplex(), but the controller is capable of doing DMAs on both channels simultaneously. Implement ATA_FLAG_IGN_SIMPLEX which makes libata ignore the simplex bit and use it in sata_uli. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
We're still seeing a lot of issues with NCQ implementation in drive firmwares. Sprious FISes during NCQ command phase occur on many drives and some of them seem potentially dangerous (at least to me). Until we find the solution, spurious messages can give us more info. Improve and limit them such that more info can be reported while not disturbing users too much. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
vt6420 completely loses its ability to raise IRQ for ATAPI devices if ATA_NIEN is diddled with in ->freeze. Further investigation is necessary to determine whether this problem is shared on other controllers but it doesn't seem to be at this point. Make vt6420's ->freeze only clear IRQ to fix this problem. This makes vt6420 relatively more prone to IRQ storms but the controller is way too braindamaged to worry about that anyway. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
- 25 1月, 2007 3 次提交
-
-
由 Alan 提交于
When set_mode() changed ->set_mode didn't adapt. This makes the needed changes and removes the relevant FIXME case. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Alan 提交于
Rather than ending up with two layers of negation jut rename the variable and lose one. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Alan 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
- 24 1月, 2007 7 次提交
-
-
由 Brian King 提交于
Fixup the inialization of qc->n_elem. It currently gets initialized to 1 for commands that do not transfer any data. Fix this by initializing n_elem to 0 and only setting to 1 in ata_scsi_qc_new when there is data to transfer. This fixes some problems seen with SATA devices attached to ipr adapters. Signed-off-by: NBrian King <brking@linux.vnet.ibm.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
Some ATA/ATAPI devices act weirdly after the link is put into slumber mode. Some hang completely requiring physical power removal while others fail to wake up till the link is hardreset a couple of times. The addition of slumber on power down was never driven by real need. It just followed what ahci spec said literally. The spec itself seems faulty in that it doesn't consider devices (not controllers) which don't support link powersaving mode. Theory never matches reality when it comes to dark allys of cheap ATA/ATAPI world. It's just unrealistic to expect vendors to test rarely used link powersaving feature rigorously. This patch makes ahci more friendly to the coldness of reality. This shouldn't have any negative effect - when suspend operation succeeds, we power off the whole machine; otherwise, we wake up everything. I can't see any reason to be so elaborate with powering down the link in the first place. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Robert Hancock 提交于
Several people reported issues with certain drive commands timing out on sata_nv controllers running in ADMA mode. The commands in question were non-DMA-mapped commands, usually FLUSH CACHE or FLUSH CACHE EXT. From experimentation it appears that the NV_INT_DEV indication isn't always set when a legitimate command completion interrupt is received on a legacy-mode command, at least not on these controllers in ADMA mode. When a command is pending on the port, force the flag on always in the irq_stat value before calling nv_host_intr so that the drive busy state is always checked by ata_host_intr. This also fixes some questionable code in nv_host_intr which called ata_check_status when a command was pending and ata_host_intr returned "unhandled". If the device interrupted at just the wrong time this could cause interrupts to be lost. Signed-off-by: NRobert Hancock <hancockr@shaw.ca> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
As with JMicron controllers, ULi M5288 sets interface fatal error bit on device error including ATAPI CC. This makes libata hardreset the port on ATAPI CC thus making it impossible to use. Ignore interface fatal error bit on ULi M5288. This fixes bugzilla bug #7837. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Adrian Bunk 提交于
This patch removes kernel 2.4 compatibility code. Signed-off-by: NAdrian Bunk <bunk@stusta.de> Acked-by: NSamuel Ortiz <samuel@sortiz.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Samuel Ortiz 提交于
With USB2.0 bulk out MTU can be 512 bytes, so checking it only for 64 bytes is incorrect. Signed-off-by: NSamuel Ortiz <samuel@sortiz.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Samuel Ortiz 提交于
Since we stop using dev_alloc_skb on the IrDA TX frame, we constantly run into the case of the skb headroom being 0, and thus we call skb_cow for every IrDA TX frame. This patch uses a local buffer and memcpy the skb to it, saving us a kmalloc for each of those IrDA TX frames. Signed-off-by: NSamuel Ortiz <samuel@sortiz.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-