Trigger device remove and then add when a catastrophic error is
detected in hardware.  This, in turn, will cause a device reset, which
we hope will recover from the catastrophic condition.

Since this might interefere with debugging the root cause, add a
module option to suppress this behaviour.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update the driver's list of HCA firmware revisions to make sure people
running Sinai firmware older than 1.1.0 get a message suggesting a
firmware upgrade.  Update the Arbel versions as well while we are at it.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This is needed if we wish to change the size of the resource structures.

Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>

Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver allocates SRQ WQEs size with a power of 2 size both for
Tavor and for memfree. For Tavor, however, the hardware only requires
the WQE size to be a multiple of 16, not a power of 2, and the max
number of scatter-gather allowed is reported accordingly by the
firmware (and this is the value currently returned by
ib_query_device() and ibv_query_device()).

If the max number of scatter/gather entries reported by the FW is used
when creating an SRQ, the creation will fail for Tavor, since the
required WQE size will be increased to the next power of 2, which
turns out to be larger than the device permitted max WQE size (which
is not a power of 2).

This patch reduces the reported SRQ max wqe size so that it can be used
successfully in creating an SRQ on Tavor HCAs.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The PCI spec recommends against drivers playing with a device's PCI
read burst size, and says that systems software should configure it.
And we actually have users that report that changing it from the
default set by BIOS hurts performance and/or stability for them.  On
the other hand, the Mellanox Programmer's Reference Manual recommends
turning it up all the way to the maximum value.  Some tests conducted
here in the lab do not show performance improvement from this tuning,
but this might be just me.

As a work-around, make this tuning an option, off by default (safe
value), with an eye towards removing it completely one day if no one
complains.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Push translation of static rate to HCA format into low-level drivers,
where it belongs.  For static rate encoding, use encoding of rate
field from IB standard PathRecord, with addition of value 0, for
backwards compatibility with current usage.  The changes are:

 - Add enum ib_rate to midlayer includes.
 - Get rid of static rate translation in IPoIB; just use static rate
   directly from Path and MulticastGroup records.
 - Update mthca driver to translate absolute static rate into the
   format used by hardware.  This also fixes mthca's static rate
   handling for HCAs that are capable of 4X DDR.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Change the mthca debugging trace output code so that it can enabled
and disabled at runtime with the debug_level module parameter in
sysfs.  Also, don't allow CONFIG_INFINIBAND_MTHCA_DEBUG to be disabled
unless CONFIG_EMBEDDED is selected.  We want users (and especially
distros) to have this turned on unless they really need to save space,
because by the time we want debugging output, it's usually too late to
rebuild a kernel.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update known firmware versions in driver's table to the latest releases.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Sinai (one-port PCI Express) HCAs get improved throughput for messages
bigger than 80 KB in DDR mode if memory keys are formatted in a
specific way.  The enhancement only works if the memory key table is
smaller than 2^24 entries.  For larger tables, the enhancement is off
and a warning is printed (to avoid silent performance loss).
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NMichael Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There are some cards around that have UAR (user access region) size
different from 8 MB.  Relax our sanity check to make sure that the PCI
BAR is big enough to access the UAR size reported by the device
firmware instead.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Check error return on call to mthca_dev_lim for Tavor
(as is done for memfree).
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move the computation of QP capabilities (max scatter/gather entries,
max inline data, etc) into the kernel, and have the uverbs module
return the values as part of the create QP response.  This keeps
precise knowledge of device limits in the low-level kernel driver.

This requires an ABI bump, so while we're making changes, get rid of
the max_sge parameter for the modify SRQ command -- it's not used and
shouldn't be there.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Report the device's real page size capability in mthca_query_device().
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Mellanox has decided that the components of the firmware version are
really meant to be displayed in decimal, e.g. 0x000400070190 is
version 4.7.400.  Change the format we use from "%x.%x.%x" to
"%d.%d.%d" to match this convention.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Set mthca_driver.owner to THIS_MODULE.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Check the sizes of CQs, QPs and SRQs when creating objects, and fail
instead of creating too-big queues.  Also return real limits instead
of just plausible-sounding values from mthca_query_device().
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Return correct atomic capability flag from mthca query function.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remember to free the multicast group context memory table.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch removes CONFIG_PCI_NAMES.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add mthca support for shared receive queues (SRQs),
including userspace SRQs.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When we call the INIT_IB firmware command to bring up a port, use
the actual port width capability returned by the QUERY_DEV_LIM
command instead of always trying to enable both 1X and 4X.  This
fixes breakage seen when the firmware is build to allow 4X only.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Remove unneeded includes of <linux/version.h>.
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for reporting HCA board ID returned from QUERY_ADAPTER
firmware command through sysfs.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Make some lawyers happy and add copyright notices for people who
forgot to include them when they actually touched the code.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update FW versions in mthca according to July 05 Mellanox release
Signed-off-by: NTziporet Koren <tziporet@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for userspace protection domains (PDs) to mthca.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Encapsulate mthca command interface initialization/cleanup.
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Fix incorrect cut-n-paste in error messages.
- Add missing newlines in error messages.
- Use DRV_NAME instead of "ib_mthca" in a couple of places.
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add Sun copyright to files modified by Tom Duffy.
Signed-off-by: NTom Duffy <tduffy@sun.com>
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Correct unwinding in error path of mthca_init_icm().
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Decouple table of HCA features from exact HCA device type.  Add a current FW
version field so we can warn when someone is using old FW.  Add support for
new MT25204 HCA.

Remove the warning about mem-free support, since it should be pretty solid at
this point.
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix RDMA in mem-free mode: we need to make sure that the RDMA context memory
is mapped for the HCA.
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean up mem-free mode support by introducing mthca_is_memfree() function,
which encapsulates the logic of deciding if a device is mem-free.
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Implement fast memory regions (FMRs), where the driver writes directly into
the HCA's translation tables rather than requiring a firmware command.  For
Tavor, MTTs for FMR are separate from regular MTTs, and are reserved at driver
initialization.  This is done to limit the amount of virtual memory needed to
map the MTTs.  For Arbel, there's no such limitation, and all MTTs and MPTs
may be used for FMR or for regular MR.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix bug in MTT allocation in mem-free mode.

I misunderstood the MTT size value returned by the firmware -- it is really
the size of a single MTT entry, since mem-free mode does not segment the MTT
as the original firmware did.  This meant that our MTT addresses ended up
being off by a factor of 8.  This meant that our MTT allocations might
overlap, and so we could overwrite and corrupt earlier memory regions when
writing new MTT entries.

We fix this by always using our 64-byte MTT segment size.  This allows some
simplification of the code as well, since there's no reason to put the MTT
segment size in a variable -- we can always use our enum value directly.
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Print IRQ number when NOP command interrupt test fails to help debugging.
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In mem-free mode, when allocating memory regions, make sure that the HCA has
context memory mapped to cover the virtual space used for the MPT and MTTs
being used.
Signed-off-by: NRoland Dreier <roland@topspin.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!