The index for a device interrupt in the PIC interrupt routing table
changes for different chips in the XLP family.  Avoid using the fixed
entries and derive the index value from the SoC device header.

Add workarounds for some devices which do not report the IRT index
correctly.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5025/Acked-by: NJohn Crispin <blogic@openwrt.org>

The XLR/XLS/XLP PIC has a 8 countdown timers which run at the PIC
frequencey. One of these can be used as a clocksource to provide
timestamps that is common across cores. This can be used in place
of the count/compare clocksource which is per-CPU.

On XLR/XLS PIC registers are 32-bit, so we just use the lower 32-bits
of the PIC counter. On XLP, the whole 64-bit can be used.

Provide common macros and functions for PIC timer registers on XLR/XLS
and XLP, and use them to register a PIC clocksource.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4786/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Create struct nlm_pic_irq for interrupts handled by the PIC.
This simplifies IRQ handling for multi-SoC as well as
the single SoC cases. Also split the setup of percpu and PIC
interrupts so that we can configure the PIC interrupts for
every node.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4467Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Upto 4 Netlogic XLP SoCs can be connected over ICI links to form a
coherent multi-node system.  Each SoC has its own set of on-chip
devices including PIC.  To support this, add a per SoC stucture and
use it for the PIC and SYS block addresses instead of using global
variables.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4469Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Remove unused and trivial PIC accesss functions, update nlm_pic_send_ipi()
and nlm_set_irt_to_cpu() to use similar logic, and use correct type for
reg in nlm_pic_disable_irt().
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4463Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Used the hardware thread id passed in while writing to IRT in
nlm_pic_init_irt()
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4465Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The XLP USB controller appears as a device on the internal SoC PCIe
bus, the block has 2 EHCI blocks and 4 OHCI blocks. Change are to:

* Add files netlogic/xlp/usb-init.c and asm/netlogic/xlp-hal/usb.h
  to initialize the USB controller and define PCI fixups. The PCI
  fixups are to setup interrupts and DMA mask.
* Update include/asm/xlp-hal/{iomap.h,pic.h,xlp.h} to add interrupt
  mapping for EHCI/OHCI interrupts.
Signed-off-by: NGanesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3756/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

- Update common files to support XLP.
- Add arch/mips/include/asm/netlogic/xlp-hal for register definitions
  and access macros
- Add arch/mips/netlogic/xlp/ for XLP specific files.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2967/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>