If VMX feature is available in the CPU, this patch will make it visible in
the /proc/cpuinfo with the cpuid detection.
Signed-Off-By: NNitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It is dangerous to shutdown the apics in machine_crash_shutdown.

With my previous patch to initialize apics in init_IRQ we should be able to
boot a kernel without this.  As long as we reinitialize the APICs we don't
care what state they were in during bootup.

This should make machine_crash_shutdown noticeably more reliable.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

All kinds of ugliness exists because we don't initialize
the apics during init_IRQs.
- We calibrate jiffies in non apic mode even when we are using apics.
- We have to have special code to initialize the apics when non-smp.
- The legacy i8259 must exist and be setup correctly, even
  when we won't use it past initialization.
- The kexec on panic code must restore the state of the io_apics.
- init/main.c needs a special case for !smp smp_init on x86

In addition to pure code movement I needed a couple
of non-obvious changes:
- Move setup_boot_APIC_clock into APIC_late_time_init for
  simplicity.
- Use cpu_khz to generate a better approximation of loops_per_jiffies
  so I can verify the timer interrupt is working.
- Call setup_apic_nmi_watchdog again after cpu_khz is initialized on
  the boot cpu.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The per cpu nmi watchdog timer is based on an event counter.  idle cpus
don't generate events so the NMI watchdog doesn't fire and the test to see
if the watchdog is working fails.

- Add nmi_cpu_busy so idle cpus don't mess up the test.
- kmalloc prev_nmi_count to keep kernel stack usage bounded.
- Improve the error message on failure so there is enough
  information to debug problems.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently we attempt to restore virtual wire mode on reboot, which only
works if we can figure out where the i8259 is connected.  This is very
useful when we kexec another kernel and likely helpful when dealing with a
BIOS that make assumptions about how the system is setup.

Since the acpi MADT table does not provide the location where the i8259 is
connected we have to look at the hardware to figure it out.

Most systems have the i8259 connected the local apic of the cpu so won't be
affected but people running Opteron and some serverworks chipsets should be
able to use kexec now.

In addition this patch removes the hard coded assumption that the io_apic
that delivers isa interrups is always known to the kernel as io_apic 0.  As
there does not appear to be anything to guarantee that assumption is true.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is platform code update for ES7000: disables IRQ overrides for the
recent ES7000 (Rascal/Zorro), cleans up the compile warning.  The patch
only affects the ES7000 subarch.

Signed-off-by: <Natalie.Protasevich@unisys.com>
Acked-by: NZwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The code that prints the cache size assumes that L3 always lives in chipset
and is shared across CPUs.  Which is not really true.

I think all the cachesizes reported by cpuid are in the processor itself.
The attached patch changes the code to reflect that.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This was reported because someone was getting oopses reading /proc/iomem.
It was tracked down to a zero-sized 'struct resource' entry which was
located right at 4GB.

You need two conditions to hit this bug: a BIOS E820_RAM area starting at
exactly the boundary where you specify mem= (to get a zero-sized entry),
and for the legacy_init_iomem_resources() loop to skip that resource (which
only happens at exactly 4G).

I think the killing zero-sized e820 entry is the easiest way to fix this.
Signed-off-by: NDave Hansen <haveblue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Hopefully fix http://bugzilla.kernel.org/show_bug.cgi?id=5235

Similar problem has been reported before here:
http://groups.google.com/group/linux.kernel/browse_thread/thread/def4ca19dbc3cd4/5cffbf349f2c87a4?tvc=2&q=Aleksey+Gorelov&hl=en#5cffbf349f2c87a4
and was related to bug in BIOS reporting 82C686 router compatible to 586.

I suspect BIOS on this board has similar issue: reports VT8235 router to be
compatible with 586 one - which is obviously not true.  Patch from the link
above has already incorporated in both 2.6 & 2.4 series, but might not work
in this particular case.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make P6 MCA initialization code complaint with guidelines in IA-32 SDM
Vol3.  Bank 0 control register should not be set by OS and clear status
registers on all banks on reset.

This will prevent false MCE alarms on the systems that has some non-MCE
information left-over in MC0_STATUS on reboot.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add an accessor function for getting the per-CPU gdt.  Callee must already
have the CPU.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The per-CPU initialization code is copying in bogus data into
thread->tls_array.  Note that it copies &per_cpu(cpu_gdt_table, cpu), not
&per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TLS_MIN).  That is totally broken
and unnecessary.  Make the initialization explicitly NULL.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch allows physical bring-up of new processors (not initially present
in the configuration) from facilities such as driver/utility implemented on
a platform.  The actual method of making processors available is up to the
platform implementation.
Signed-off-by: NNatalie Protasevich <Natalie.Protasevich@unisys.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Join together some common functions (pmd_page{,_kernel}) over 2level and
3level pages.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial internal version of Venki's cpuid(4) deterministic cache parameter
identification patch used static arrays of size MAX_CACHE_LEAVES.  Final patch
which made to the base used dynamic array allocation, with this
MAX_CACHE_LEAVES limit hunk still in place.

cpuid(4) already has a mechanism to find out the number of cache levels
implemented and there is no need for this hardcoded MAX_CACHE_LEAVES limit.

So remove the MAX_CACHE_LEAVES limit from the routine which calculates the
number of cache levels using cpuid(4)
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There exists a field io_bitmap_owner in the TSS that is only checked, but
never set to anything else but NULL.
Signed-off-by: NBart Oldeman <bartoldeman@users.sourceforge.net>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

mxcsr_feature_mask_init isn't needed in suspend/resume time (we can use
boot time mask).  And actually it's harmful, as it clear task's saved
fxsave in resume.  This bug is widely seen by users using zsh.

(akpm: my eyes.  Fixed some surrounding whitespace mess)

Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This adjusts i386's cmpxchg patterns so that

- for word and long cmpxchg-es the compiler can utilize all possible
  registers

- cmpxchg8b gets disabled when the minimum specified hardware architectur
  doesn't support it (like was already happening for the byte, word, and
  long ones).
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I just found out that some precision is unnecessarily lost in the
arch/i386/kernel/timers/timer_tsc.c:set_cyc2ns_scale function.  It uses a
cpu_mhz parameter when it could use a cpu_khz.  In the specific case of an
Intel P4 running at 3001.171 Mhz, the truncation to 3001 Mhz leads to an
imprecision of 19 microseconds per second : this is very sad for a timer with
nearly nanosecond accuracy.

Fix the x86_64 architecture too.

Cc: george anzinger <george@mvista.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch removes a bunch of unecessary checks for (size_t < 0) in
selinuxfs.
Signed-off-by: NJames Morris <jmorris@namei.org>
Acked-by: NStephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

security/selinux/hooks.c: In function `selinux_inode_getxattr':
security/selinux/hooks.c:2193: warning: unused variable `sbsec'

Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch allows SELinux to canonicalize the value returned from
getxattr() via the security_inode_getsecurity() hook, which is called after
the fs level getxattr() function.

The purpose of this is to allow the in-core security context for an inode
to override the on-disk value.  This could happen in cases such as
upgrading a system to a different labeling form (e.g.  standard SELinux to
MLS) without needing to do a full relabel of the filesystem.

In such cases, we want getxattr() to return the canonical security context
that the kernel is using rather than what is stored on disk.

The implementation hooks into the inode_getsecurity(), adding another
parameter to indicate the result of the preceding fs-level getxattr() call,
so that SELinux knows whether to compare a value obtained from disk with
the kernel value.

We also now allow getxattr() to work for mountpoint labeled filesystems
(i.e.  mount with option context=foo_t), as we are able to return the
kernel value to the user.
Signed-off-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NStephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch converts SELinux code from kmalloc/memset to the new kazalloc
unction.  On i386, this results in a text saving of over 1K.

Before:
text    data     bss     dec     hex filename
86319    4642   15236  106197   19ed5 security/selinux/built-in.o

After:
text    data     bss     dec     hex filename
85278    4642   15236  105156   19ac4 security/selinux/built-in.o
Signed-off-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add CONFIG_X86_32 for i386.  This allows selecting options that only apply
to 32-bit systems.

(X86 && !X86_64) becomes X86_32
(X86 ||  X86_64) becomes X86
Signed-off-by: NBrian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Since CONFIG_IKCONFIG_PROC already depends on CONFIG_IKCONFIG, adding
configs.o again is redundant.
Signed-off-by: NBrian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Doh!
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Petr Vandrovec correctly points out that the SMB region of the PIIX4 is
just 16 bytes, not 32.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A few drivers were not following the standard meme of printing out
their driver name and version at module load time; this is fixed
as well.

ata_pci_init_one() receives an array of struct ata_port_info.  Recent
updates to the code had always obtained port information from
array element 0, rather than array element N.

Change to avoid hardcoding port_info[0], thereby restoring proper
hardware information to secondary legacy ports.

The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error.  On legacy PCI IDE hardware, the latter
is often implicit in the former.  On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.

Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.

This will lead to more flexible error handling in the future.

move EXPORT_SYMBOL(filemap_populate) to the proper place: just after
function itself: it's easy to miss that function is exported otherwise.
Signed-off-by: NNikita Danilov <nikita@clusterfs.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In 'mm' change the explicit use of a for-loop using NR_CPUS into the
general for_each_cpu() constructs.  This widens the scope of potential
future optimizations of the general constructs, as well as takes advantage
of the existing optimizations of first_cpu() and next_cpu(), which is
advantageous when the true CPU count is much smaller than NR_CPUS.
Signed-off-by: NJohn Hawkes <hawkes@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Policy contextualization is only useful for task based policies and not for
vma based policies.  It may be useful to define allowed nodes that are not
accessible from this thread because other threads may have access to these
nodes.  Without this patch strange memory policy situations may cause an
application to fail with out of memory.

Example:

Let's say we have two threads A and B that share the same address space and
a huge array computational array X.

Thread A is restricted by its cpuset to nodes 0 and 1 and thread B is
restricted by its cpuset to nodes 2 and 3.

Thread A now wants to restrict allocations to the first node and thus
applies a BIND policy on X to node 0 and 2.  The cpuset limits this to node
0.  Thus pages for X must be allocated on node 0 now.

Thread B now touches a page that has never been used in X and faults in a
page.  According to the BIND policy of the vma for X the page must be
allocated on page 0.  However, the cpuset of B does not allow allocation on
0 and 1.  Now the application fails in alloc_pages with out of memory.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Do a separation between do_xxx and sys_xxx functions. sys_xxx functions
  take variable sized bitmaps from user space as arguments. do_xxx functions
  take fixed sized nodemask_t as arguments and may be used from inside the
  kernel. Doing so simplifies the initialization code. There is no
  fs = kernel_ds assumption anymore.

- Split up get_nodes into get_nodes (which gets the node list) and
  contextualize_policy which restricts the nodes to those accessible
  to the task and updates cpusets.

- Add comments explaining limitations of bind policy
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Here is a set of ppc64 specific patches that at least allow
compilation/booting with the following configurations:

FLATMEM
SPARSEMEN
SPARSEMEM + MEMORY_HOTPLUG
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NDave Hansen <haveblue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>