Intel MID UART quirks require already quite a bit of code
in 8250_pci.c. On new Intel platforms where it is used, the
integrated DMA engine no longer has its own PCI device, but
is instead configured from the UART's MMIO. That means we
will have to add even more code for handling just MID UARTs.

Instead of adding that to 8250_pci.c, splitting the support
of Intel MID UART into its own driver. Handling of the
integrated DMA engine becomes much simpler this way. Own
driver will also remove the need for things like specific
set_termios hooks for every board using this UART, and
simplify the handling of it in general.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Clearing UART_MCR_RTS or UART_MCR_XONANY is unnecessary; these bits
are never set in the shadow mcr. The RTS clear is especially confusing.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The same serial hardware is present on LS2080A which is arm64, and
LS1021A which is arm32, so don't limit the workaround to PPC.

Unlike PPC which uses arch/powerpc/kernel/legacy_serial.c, the ARM
targets use drivers/tty/serial/of_serial.c, so add the handle_irq
override check there as well.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds an entry to the uart_config table for PORT_RT2880
enabling rx/tx FIFOs.  The UART is actually a Palmchip BK-3103
which is found in several devices from Alchemy/RMI, Ralink, and
Sigma Designs.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

RX buffer is allocated from DMA coherent memory. Thus there is no need to call
DMA sync API for it.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move h/w reinit of serial console restore-from-suspend into
standalone helper function.

No functional change.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the UART clock is set slightly under 1.8432MHz, the 8250 driver
core doesn't permit the 115200 baud rate since it calculates the maximum
frequency to pass to uart_get_baud_rate by simply dividing the uart
clock by 16 which yields a value slightly under 115200, even though the
frequency is close enough for the UART to operate reliably.

Therefore add some tolerance in the calculation of the maximum baud
rate. 1% tolerance allows for marginally slower uart clk than nominal
without introducing transmission errors.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
[pjh: Forward-port & refactor original patch; change tolerance to 1%]
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some SoCs, including Ralink/Mediatek and Alchemy Au1xxx, have a
16550-like UART with a non-standard register layout.  These are
supported by a simple mapping table in 8250_port.c  Rather than
list every SoC type using this access mode in the ifdefs there,
allow selecting the SERIAL_8250_RT288X Kconfig option with any
system and default it to y for the known cases needing it.  The
help text is reworded accordingly.

This change simplifies adding support for other SoCs also using
the same UART.

The name of the option is a little misleading, but not knowing
the true origin of this UART, it is as good a choice as any.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

serial8250_register_8250_port adds it to all ports it
registers. No need to set it separately.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Using the same style of declaring variables as used in the
other functions of the driver. Passing uart_port to the
function instead of uart_8250_port, as it is the one mostly
needed.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the extra return.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding comment where the purpose of the function is
explained.

The dma parameters are not used, so removing them, and also
moving the assignment of the function to the same place
where the other dw8250_data structures members are being set
in dw8250_probe.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the DW_apb_uart is configured with UART_16550_COMPATIBLE
configuration parameter set, then the Busy Functionality is
not available. These UARTs will never generate the Busy
detect indication interrupt, and therefore don't need
handling for it.

This creates a small optimization for the DW_apb_uarts
configured without the busy functionality, but more
importantly, it removes the small but real risk of hitting
potential issues caused by busy functionality handling when
no busy functionality exist.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merging the DT and ACPI specific probe functions into
dw8250_quirks. Those functions did not have that much code
any more and some of the quirks need to be shared. This
will also allow platforms without DT or ACPI to use the
driver.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a flag "skip_autocfg" that the platforms that do
not have the ADDITIONAL_FEATURES implemented can use to skip
the port setup. It's then enough to call dw8250_setup_port
just from dw8250_probe based on that flag.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of assigning the dma member in dw8250_probe_of and
dw8250_probe_acpi separately, assigning it in dw8250_probe.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This makes the properties available for all types of
platforms instead of just the ones using DT.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For convenience, adding separate pointer for the "port"
member of struct uart_8250_port that is being filled in the
probe function.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This allows earlycon to be used without needing to specify the I/O
address on the kernel command line, if linux,stdout-path is specified
in the chosen node.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable the TX/RX FIFOs present on UARTs in Ingenic SoCs.
FIFO sizes vary per device so match these based on
the OF compatible string

Enabling the FIFOs permits much faster transfer with
lower CPU overhead.

Tested on Ingenic JZ4780 on the MIPS Ci20 Creator board
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Ingenic UART is similar to a standard 16550, but hardware flow control
requires setting a couple of additional, non-standard bits in the MCR.

The non-standard "modem control enable" and "hardware flow control
mode" bits are set when writing to the MCR register, based
on whether the modem control interrupt is active.

Additionally the non-16550 compliant parts of the uart need to be
masked from higher layers.

Tested on Ingenic JZ4780 on MIPS Creator Ci20 board
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The following race conditions can happen when a serial port is used
as console.

Case1: CPU_B is used to detect an interrupt from a serial port,
       but it can have interrupts disabled during the waiting time.
Case2: CPU_B clears UART_IER just after CPU_A sets UART_IER and then
       a serial port may not make an interrupt.
Case3: CPU_A sets UART_IER just after CPU_B clears UART_IER.
       This is an unexpected behavior for serial8250_console_write().

CPU_A [autoconfig_irq]      |  CPU_B [serial8250_console_write]
----------------------------|---------------------------------------
                            |
probe_irq_on()              |  spin_lock_irqsave(&port->lock,)
serial_outp(,UART_IER,0x0f) |  serial_out(,UART_IER,0)
udelay(20);                 |  uart_console_write()
probe_irq_off()             |
                            |  spin_unlock_irqrestore(&port->lock,)

Case1 and 2 can make autoconfig_irq() failed.
In these cases, the console doesn't work in interrupt mode and
"input overrun" (which can make operation mistakes) can happen
on some systems. Especially in the Case1, It is known that the
problem happens with high rate every boot once it occurs
because the boot sequence is always almost same.

port mutex makes sure that the autoconfig operation is exclusive of
any other concurrent HW access except by the console operation.
console lock is required in autoconfig_irq().
Signed-off-by: NTaichi Kageyama <t-kageyama@cp.jp.nec.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

8250/Kconfig:config SERIAL_8250_LPC18XX
8250/Kconfig:        bool "NXP LPC18xx/43xx serial port support"

...meaning that it currently is not being built as a module by anyone.

When targetting orphaned modular code in non-modular drivers, this
came up.  Joachim indicated that the driver was actually meant to
be tristate but ended up bool by accident.  So here we make it
tristate instead of removing the modular code that was essentially
orphaned.
Suggested-by: NJoachim Eastwood <manabian@gmail.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CIR type serial ports aren't real serial ports.

This is just a way to prevent legacy 8250 serial
driver from probing and eventually binding some
resources.

Since in current state such ports aren't providing
any real functionality and it is not possible
to change their type via setserial/ioctl(TIOCSSERIAL)
(due to UPF_FIXED_PORT flag set on them)
it is simpler and cleaner to not register them at all
with serial core.

Print a short message in this case so it is known
to user what has happened.

This way checks for PORT_8250_CIR in serial port
callbacks can be removed too, since they won't
ever be called.
Signed-off-by: NMaciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The function tty_insert_flip_string() returns an int and as such it
might fail. So the result is that I kindly asked to insert 48 bytes and
the function only insterted 32.
I have no idea what to do with the remaining 16 so I think dropping them
is the only option. I also increase the buf_overrun counter so userpace
has a clue that we lost bytes.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The split of the 8250 driver into a 8250_base/8250.ko resulted in a
lack of a license for the 8250_base.ko module. This caused the module
to fail to load and the kernel to be tainted. Add the appropriate
MODULE_LICENSE to 8250_port.c, which is always compiled into
8250_base.ko
Signed-off-by: NJonathan McDowell <noodles@earth.li>
Reported-by: NMikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

That bitfield is modified by read + or + write operation. If someone
sets any of the other two bits it might render the lock useless.

While at it, remove other bitfields as well to avoid more such
errors.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn Ogness <john.ogness@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The 8250-omap driver requires the DMA-engine driver to support the pause
command in order to properly turn off programmed RX transfer before the
driver stars manually reading from the FIFO.
The lacking support of the requirement has been discovered recently. In
order to stay safe here we disable RX-DMA completly on probe.
The rx_dma_broken assignment on probe could be removed once we working
pause function in omap-dma.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the serial core is informed that this device is doing
automatic flow control, it is not necessary to alter CTS and
DCTS of the MSR as the core no longer attempts stop the port
in uart_handle_cts_change().
Signed-off-by: NHuiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: NQipeng Zha <qipeng.zha@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This way this device can be used with irtty-sir -
at least on Toshiba Satellite A20-S103 it is not configured by default
and needs PNP activation before it starts to respond on I/O ports.

This device has actually its own driver (ali-ircc),
but this driver seems to be non-functional for a very long time
(see http://permalink.gmane.org/gmane.linux.irda.general/484
http://permalink.gmane.org/gmane.network.protocols.obex.openobex.user/943
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=535070 ).
Signed-off-by: NMaciej Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

SMSC IrCC SIR/FIR port should not be bound to by
(legacy) serial driver so its own driver (smsc-ircc2)
can bind to it.
Signed-off-by: NMaciej Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt,
and ioremap_cache, tree-wide.
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Fix RS232/485 mode incorrect setting after S3/S4 resume for F81504/508/512

We had add RS232/485 RTS control with fecf27a3. But when it
resume from S3/S4, the mode register 0x40 + 0x08 * idx + 7 will
rewrite to 0x01 (RS232 mode).

This patch will modify 2 sections.

One is pci_fintek_init(), if it called when first init, it will
write mode register with 0x01. If it called from S3/S4 resume,
it's will get the relative port data and pass it to
pci_fintek_rs485_config() with NULL rs485 parameter.

The another modification is in pci_fintek_rs485_config(). It'll
re-apply old configuration when the parameter rs485 is NULL.
Signed-off-by: NPeter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.
Signed-off-by: NAdam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.

There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.

This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: NHuiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: NQipeng Zha <qipeng.zha@intel.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If serial8250_register_8250_port() fails, disable and unprepare the
clock before exiting.

Fixes: 1a8d2903 ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add RS485 control for Fintek F81504/508/512

F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.

When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.

When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.

When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.

We will force 0x01 on pci_fintek_setup().
Signed-off-by: NPeter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The XR17V35X UART needs the ECB bit set in its XR_EFR
register to enable access to IER [7:5], ISR [5:4], FCR[5:4],
MCR[7:5], and MSR [7:0].

Also reset the IER register to mask interrupts after access
to all bits of this register has been enabled.

This makes my 8-port XR17V35X working with the in-kernel
serial driver.

Cc: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: NJoerg Roedel <jroedel@suse.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Reviewed-by: NMichael Welling <mwelling@ieee.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

An already-active sender can swamp the interrupt handler with
"too much work" if the rx interrupts are enabled when the fifo is
disabled and operating in single-byte mode.

Defer rx and line status interrupt enable until after the fifos
are enabled in set_termios(), but at least initialize the shadow
IER value with the interrupts which will be enabled.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>