Commit 0046be10e0c502705fc74d91408eba13a73bc201 ("mips: delete
non-required instances of include <linux/init.h>") inadvertently
removed an include that was actually correct.  Restore it.

Note that it gets init.h implicitly anyway, so this is largely a
cosmetic fixup; no build regressions were caused by this.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6416/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
F7D4302 are reasonable guesses which are unlikely to cause
mis-detection.
Signed-off-by: NCody P Schafer <devel@codyps.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Cc: Cody P Schafer <devel@codyps.com>
Patchwork: https://patchwork.linux-mips.org/patch/6594/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds board detection for the Siemens SE505v2 and the led gpio
configuration. This board does not have any buttons.
This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6593/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds led and button GPIO configuration for Linksys wrt54g3gv2,
wrt54gsv1 and wrtsl54gs. This is based on OpenWrt broadcom-diag code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6592/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Linksys WRT54G/GS/GL family uses the same boardtype numbers, and
the same gpio configuration. The boardtype numbers are changing with
the hardware versions, but these hardware numbers are different or each
model.
Detect them all as one device, this also worked in OpenWrt.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6591/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6597/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The M5150 core is a 32-bit MIPS RISC which implements the
MIPS Architecture Release-5  in a 5-stage pipeline.
In addition, it includes the MIPS Architecture Virtualization Module
that enables virtualization of operating systems,
which provides a scalable, trusted, and secure execution environment.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6596/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6595/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6581/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The previous NR_CPUS=2 default is not an optimal default for current
Malta setups where it is common to have more than 2 CPUs available. It
makes sense to increase this to a number which covers all common setups
currently in use, such that all of those cores are usable. 8 seems to
fit that description.

If the user has less than 8 CPUs & they wish to have a more optimal
kernel they can simply reduce this in their config. It makes sense for
the default to work on as many systems as possible.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6580/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

For Malta defconfigs which may run on an SMP configuration without
hardware cache anti-aliasing, a 16KB page size is a safer default.
Most notably at the moment it will avoid cache aliasing issues for
multicore proAptiv systems.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6579/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Recent versions of udev and systemd require the kernel
to be compiled with CONFIG_DEVTMPFS in order to populate
the /dev directory. Most MIPS platforms have it enabled by
default, so enable it for Malta configs as well.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6582/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch simply regenerates the malta defconfigs such that they don't
change after being used & saved as a defconfig again. ie. it is the
result of running the following:

for cfg in arch/mips/configs/malta*; do
	ARCH=mips make `basename ${cfg}`
	ARCH=mips make savedefconfig
	mv -v defconfig ${cfg}
done
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6578/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The au1xxx-ide driver isn't any faster than pata_platform since it
spends a lot of time busy waiting for DMA to finish; faster PIO/DMA
modes only work on the db1200 with a certain cpu speed, UDMA is broken,
and finally the old IDE layer is on death row, so time to switch to
the newer ATA layer.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6662/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Merge the db1200.h and db1300.h headers into their only users.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6660/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch merges support for all DB1xxx and PB1xxx
boards into a single image, along with a new single defconfig
for them.

Run-tested on DB1300 and DB1500.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6577/
Patchwork: https://patchwork.linux-mips.org/patch/6659/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

All Alchemy chips have coherent DMA, but for example the USB or AC97
peripherals on the Au1000/1500/1100 are not.
This patch uses DMA_MAYBE_COHERENT on Alchemy and sets coherentio based
on CPU type.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6576/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Setting DMA_MAYBE_COHERENT gives a platform the opportunity to select
use of cache ops at boot.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6575/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Allow secondary cores to program their segment control registers
during smp bootstrap code. This enables EVA on Malta SMP
configurations
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Shift System Controller memory mapping to 0x80000000
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Use a Malta specific function to free the init section once the
kernel has booted. When operating in EVA mode, the physical memory
is shifted to 0x80000000. Kernel is loaded into 0x80000000 (virtual)
so the offset between physical and virtual addresses is 0.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

PHYS_OFFSET is used to denote the physical start address of the
first bank of RAM. When the Malta board is in EVA mode, the physical
start address of RAM is shifted to 0x80000000 so it's necessary to use
this macro in order to make the code EVA agnostic.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

The 'ememsize' variable is used to denote the real RAM which is
present on the Malta board. This is different compared to 'memsize'
which is capped to 256MB. The 'ememsize' is used to get the actual
physical memory when setting up the Malta memory layout. This only
makes sense in case the core operates in the EVA mode, and it's
ignored otherwise.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Add a spaces.h file for Malta to override certain memory macros
when operating in EVA mode.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

The Malta board aliases 0x80000000 - 0xffffffff to 0x00000000
- 0x7fffffff ignoring the 256 MB IO hole in 0x10000000.
The physical memory is shifted to 0x80000000 so up to 2GB
can be used. Kuseg is expanded to 3GB (due to board limitations
only 2GB can be accessed) and lowmem (kernel space) is expanded to 2GB.

The Segment Control registers are programmed as follows:

Virtual memory           Physical memory           Mapping
0x00000000 - 0x7fffffff  0x80000000 - 0xfffffffff   MUSUK (kuseg)
0x80000000 - 0x9fffffff  0x00000000 - 0x1ffffffff   MUSUK (kseg0)
0xa0000000 - 0xbf000000  0x00000000 - 0x1ffffffff   MUSUK (kseg1)
0xc0000000 - 0xdfffffff             -                 MK  (kseg2)
0xe0000000 - 0xffffffff             -                 MK  (kseg3)

The location of exception vectors remain the same since 0xbfc00000
(traditional exception base) still maps to 0x1fc00000 physical.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

There is a chance for the secondary cache to have memory
aliases. This can happen if the bootloader is in a non-EVA mode
(or even in EVA mode but with different mapping from the kernel)
and the kernel switching to EVA afterwards. It's best to flush
the icache to avoid having the secondary CPUs fetching stale
data from it.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Use the userspace cache flushing functions if the interrupted
process is a userspace one.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Build EVA specific cache flushing functions (ie cachee).
They will be used by a subsequent patch.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

A core in EVA mode can have any possible segment mapping, so the
default free_initmem_default() function may not always work as expected.
Therefore, add a callback that platforms can use to free up the init section.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

The MIPS *Aptiv family uses bit 28 in Config5 CP0 register to
indicate whether the core supports EVA or not.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

This will allow platforms to use an alternative way to get
the physical address of a symbol.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

When flushing the icache, make sure the address limit is correct
so the appropriate 'cache' instruction will be used. This has no
impact on cores operating in non-eva mode. However, when EVA is
enabled, we ensure that 'cache' will be used instead of 'cachee'.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Add EVA cache flushing functions similar to non-EVA configurations.
Because the cache may or may not contain user virtual addresses, we
need to use the 'cache' or 'cachee' instruction based on whether we
flush the cache on behalf of kernel or user respectively.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

Build code to invalidate an address range in the  instruction cache
using the Hit Invalidate cache operation.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

EVA does not have FPU specific instructions for reading or writing
FPU registers from userspace memory.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

A MIPS specific csum_and_copy_from_user function is necessary because
the generic one from include/net/checksum.h will not work for EVA.
This is because the generic one will link to symbols from lib/checksum.c
which are not EVA aware.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>