- 29 8月, 2015 8 次提交
-
-
由 Christoph Hellwig 提交于
Add a single list of devices that need non-ALUA device handlers to the core scsi_dh code so that we can autoload the modules for them at probe time. While this is a little ugly in terms of architecture it actually significantly simplifies the code in addition to the new autoloading functionality. Signed-off-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NHannes Reinecke <hare@suse.de> Acked-by: NMike Snitzer <snitzer@redhat.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Christoph Hellwig 提交于
Stop building scsi_dh as a separate module and integrate it fully into the core SCSI code with explicit callouts at bus scan time. For now the callouts are placed at the same point as the old bus notifiers were called, but in the future we will be able to look at ALUA INQUIRY data earlier on. Note that this also means that the device handler modules need to be loaded by the time we scan the bus. The next patches will add support for autoloading device handlers at bus scan time to make sure they are always loaded if they are enabled in the kernel config. Signed-off-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NHannes Reinecke <hare@suse.de> Acked-by: NMike Snitzer <snitzer@redhat.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Christoph Hellwig 提交于
Prepare for building scsi_dh.c into the core SCSI module by moving it to drivers/scsi. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NHannes Reinecke <hare@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Christoph Hellwig 提交于
This way we can reused the same code any attachment method, not just those requested from dm-mpath. [jejb: fixup checkpatch error] Signed-off-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NHannes Reinecke <hare@suse.de> Acked-by: NMike Snitzer <snitzer@redhat.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Christoph Hellwig 提交于
While allowing dm-mpath to attach device handlers is a functionality we need for backwards compatibility reason there is no reason to reference count them and detach them if dm-mpath stops using the device for some reason. If the device handler works for the given device it can just stay attached, and we can take the retain_hw_handler codepath. Signed-off-by: NChristoph Hellwig <hch@lst.de> Acked-by: NMike Snitzer <snitzer@redhat.com> Acked-by: NHannes Reinecke <hare@Suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Hannes Reinecke 提交于
If no user settings are found it's pointless trying to read them from flash. So skip that step. This also fixes a compilation warning about uninitialized variables in aic94xx. Signed-off-by: NHannes Reinecke <hare@suse.de> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Gabriel Krisman Bertazi 提交于
Remove unnecessary check that disabled SIS pipe commands for SIS-32 devices. This change was sufficient to enable raw mode and send SIS pipe commands for a 57B3 device. Fixes: f8ee25d7 ("ipr: AF DASD raw mode implementation in ipr driver") Signed-off-by: NGabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by: NBrian King <brking@linux.vnet.ibm.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Gabriel Krisman Bertazi 提交于
Disable underlength error verification based on count of bytes actually transferred for AF DASD devices when SIS pipe mode is enabled. This avoids unexpected underlength errors when issuing some commands in raw mode. Signed-off-by: NGabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by: NBrian King <brking@linux.vnet.ibm.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
- 28 8月, 2015 20 次提交
-
-
由 Sreekanth Reddy 提交于
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Issue: When the disks are getting discovered and assigned device handles by the kernel, a device block followed by an unblock (due to broadcast primitives) issued by the driver is interspersed by the kernel changing the state of the device. Therefore the unblock by the driver results in a no operation within the kernel API. To fix this one, the below patch checks the return of the unblock API and performs a block followed by an unblock to unfreeze the block layer's I/O queue. Sufficient checks and prints are also added in the driver to identify this condition caused by the kernel. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Added dma_mapping_error() API after mapping an address with dma_map_single() API. Otherwise when CONFIG_DMA_API_DEBUG is enabled in the kernel, then it complains about mpt3sas driver not calling dma_mapping_error after mapping an address with dma_map_single Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Created a thread using alloc_ordered_workqueue() API in order to process the works from firmware Work-queue sequentially instead of create_singlethread_workqueue() API. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJoe Lawrence <joe.lawrence@stratus.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
"VendorID" "DeviceID" "SubsystemVendor ID" "SubsystemDevice ID" Cisco Branding String 0x1000 0x97 0x1137 0x154 Cisco 9300-8i 12Gbps SAS HBA 0x1000 0x97 0x1137 0x155 Cisco 12G Modular SAS Pass through Controller 0x1000 0x97 0x1137 0x156 UCS C3X60 12G SAS Pass through Controller Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
mpt3sas: Return host busy error status to SML when DMA mapping of scatter gather list fails for a SCSI command scsi_dma_map API will return a negative value (i.e. -ENOMEM) if DMA mapping of sg lists fails and zero if the sg list in the SCSI cmd is NULL. But drivers doesn't handled sg list DMA mapping failure case properly. So, Updated the code to return host busy error status to SCSI MID Layer(SML), when DMA mapping of scatter gather list fails for a SCSI command. So that SML will retry this SCSI cmd after some time. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
For any SCSI command, if the driver receives IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then that command will be completed with DID_RESET host status. The definition of this log info value is "Virtual IO has failed and has to be retried". Firmware will provide this log info value with IOC Status "SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume) is pulled and pushed back within some minimal delay. With this log info value, firmware informs the driver to retry the failed IO command infinite times, so to provide some time for the firmware to discover the reinserted drive successfully instated of just retrying failed command for five times(doesn't giving enough time for firmware to complete the drive discovery) and failing the IO permanently even though drive came back successfully. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Below are the new changes to MPI 2.5 Rev K(2.5.6) specification and 2.00.35 header files 1) Added a minimum size requirement for target mode command buffers. 2) Added MinMSIxIndex and MaxMSIxIndex fields to CommandBufferPostBase Request. 3) For BIOS Page 1, added SSUTimeout field, and added Product Name String Format bits to the BiosOptions field Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Add the following OEM's branding to the mpt3sas driver. "VendorID" "DeviceID" "SubsystemVendor ID" "SubsystemDevice ID" Cisco Branding String 0x1000 0x97 SVID = 0x1137 0x014C Cisco 9300-8E 12G SAS HBA Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Added the following Dell branding to the mpt3sas driver. "VendorID" "DeviceID" "SubsystemVendor ID" "SubsystemDevice ID" Dell Branding String 0x1000 0x0097 0x1028 0x1F46 DELL 12Gbps HBA Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Following is the change set, 1. Added more defines for the BiosOptions field of MPI2_CONFIG_PAGE_BIOS_1. 2. Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC definition. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
This Patch will provide more details of the devices such as slot number, enclosure logical id, enclosure level & connector name in the following scenarios, - When end device is added in the topology, - When the end device is removed from the setup, - When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during error handling, - When any command to the device fails with Sense key Hardware error or Medium error or Unit Attention, - When firmware returns device error or device not ready status for the end device, - When a Predicted fault is detected on an end device. This information can be used by the user to identify the location of the desired drive in the topology. Driver will get these information by reading the sas device page0. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Update MPI 2.5 Release: MPI 2.5 Rev I (2.5.4) specification and 2.00.33 header files Below is the change set from the MPI specification for I Rev 1) Added Base Enclosure Level bit to the Flags field of Manufacturing Page 7. 2) Updated description of the MaxTargetPortConnectTime field of SAS IO Unit Page 1. 3) Added EnclosureLevel and ConnectorName fields to SAS Device Page 0. Also, added EnclosureLevel and ConnectorName Valid bit to the Flags field. 4) Added EnclosureLevel field to SAS Enclosure Page 0. Also, added EnclosureLevel Valid bit to the Flags field. 5) Added value for BIOS image to HashImageType. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
During hot-plugging of a disk(having a flaky link), the disk addition stops and any further disk addition or removal doesn't happen on that controller. This is because, when driver receives DELAY_NOT_RESPONDING event for a disk while it is undergoing addition at the SCSI Transport layer, the driver would block the I/O to that disk resulting in a deadlock. i.e the disk addition work couldn't be completed at the SCSI Transport Layer as it can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as I/Os are blocked to this drive. Also any subsequent device removal (TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be processed as they are in the queue to get processed after disk addition event. Description of Change: Don't block the drive when drive addition is under the control of SML. So that SML won't be blocked of issuing the device dicovery commands (such as Inquiry, Report LUNs etc). Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
mpt3sas: Get IOC_FACTS information using handshake protocol only after HBA card gets into READY or Operational state. Driver initialization fails if driver tries to send IOC facts request message when the IOC is in reset or in a fault state. This patch will make sure that 1.Driver to send IOC facts request message only if HBA is in operational or ready state. 2.If IOC is in fault state, a diagnostic reset would be issued. 3.If IOC is in reset state then driver will wait for 10 seconds to exit out of reset state. If the HBA continues to be in reset state, then the HBA wouldn't be claimed by the driver. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NTomas Henzl <thenzl@redhat.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Sreekanth Reddy 提交于
In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to up-to 96. Following are changes that are done in this patch 1. This feature is enabled only for SAS3 C0 and higher revision cards and also only when reply post free queue count is greater than 8. 2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces are used. MSI-X index numbered from 0 to 7 use the first SupplementalReplyPostHostIndex system interface to update its corresponding ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the second SupplementalReplyPostHostIndex system interface and so on. These 12 SuppementalReplyPostHostIndex system interfaces address are saved in the array replyPostRegisterIndex[]. 3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X vectors. So MSIxIndex field in these register must contain a value between 0 and 7. 4. After processing the reply descriptors from a reply post free queues then update the new reply post host index value in ReplyPostHostIndex field and (msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex register. The Address of this SupplementalReplyPostHostIndex register is retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array. Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
- 27 8月, 2015 12 次提交
-
-
由 Dan Carpenter 提交于
We recently did some cleanup here and now the static checkers notice that there is a missing error code when ioremap() fails. Let's set it to -ENOMEM. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 K. Y. Srinivasan 提交于
In the function storvsc_channel_init(), error code was not getting set correctly in some of the failure cases. Fix this issue. Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com> Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Keith Mange 提交于
Allow WRITE_SAME for Windows10 and above hosts. Tested-by: NAlex Ng <alexng@microsoft.com> Signed-off-by: NKeith Mange <keith.mange@microsoft.com> Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Keith Mange 提交于
Use storage protocol version instead of vmbus protocol version when determining storage capabilities. Tested-by: NAlex Ng <alexng@microsoft.com> Signed-off-by: NKeith Mange <keith.mange@microsoft.com> Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Keith Mange 提交于
Use correct defaults for values determined by protocol negotiation, instead of resetting them with every scsi controller. Tested-by: NAlex Ng <alexng@microsoft.com> Signed-off-by: NKeith Mange <keith.mange@microsoft.com> Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Keith Mange 提交于
Currently we are making decisions based on vmbus protocol versions that have been negotiated; use storage potocol versions instead. [jejb: fold ARRAY_SIZE conversion suggested by Johannes Thumshirn <jthumshirn@suse.de> make vmstor_protocol static] Tested-by: NAlex Ng <alexng@microsoft.com> Signed-off-by: NKeith Mange <keith.mange@microsoft.com> Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Keith Mange 提交于
Use a single value to track protocol versions to simplify comparisons and to be consistent with vmbus version tracking. Tested-by: NAlex Ng <alexng@microsoft.com> Signed-off-by: NKeith Mange <keith.mange@microsoft.com> Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Keith Mange 提交于
Rather than look for sets of specific protocol versions, make decisions based on ranges. This will be safer and require fewer changes going forward as we add more storage protocol versions. Tested-by: NAlex Ng <alexng@microsoft.com> Signed-off-by: NKeith Mange <keith.mange@microsoft.com> Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Matthew R. Ochs 提交于
The queuecommand routine has a local dev pointer used for the dev_* prints. The two prints that currently exist are tucked under a debug define and thus can be left out. Use the actual location instead of a local to avoid this warning. This patch is intended to be applied after the "CXL Flash Error Recovery and Superpipe" series. Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com> Reported-by: Nkbuild test robot <fengguang.wu@intel.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Dan Carpenter 提交于
"port_sel" is a u64 so the shifting should also be a 64 bit shift. Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter') Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de> Acked-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Dan Carpenter 提交于
The > should be >= or we read one element past the end of the array. Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter') Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Acked-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-
由 Matthew R. Ochs 提交于
Add support for physical LUN segmentation (virtual LUNs) to device driver supporting the IBM CXL Flash adapter. This patch allows user space applications to virtually segment a physical LUN into N virtual LUNs, taking advantage of the translation features provided by this adapter. Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com> Reviewed-by: NMichael Neuling <mikey@neuling.org> Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by: NJames Bottomley <JBottomley@Odin.com>
-