- 26 5月, 2010 2 次提交
-
-
由 Sathya Perla 提交于
Sometimes BE requires longer time for POST completion after an EEH reset. Increasing the timeout value accordingly. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sarveshwar Bandi 提交于
Certain firmware commands/operations to upgrade firmware could take several seconds to complete. The code presently disables bottom half during these operations which could lead to unpredictable behaviour in certain cases. This patch now does all firmware upgrade operations asynchronously using a completion variable. Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 5月, 2010 1 次提交
-
-
由 Sarveshwar Bandi 提交于
PCI function reset needs to invoked after fw init ioctl is issued. Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 5月, 2010 1 次提交
-
-
由 Joe Perches 提交于
This patch removes from drivers/net/ all the unnecessary return; statements that precede the last closing brace of void functions. It does not remove the returns that are immediately preceded by a label as gcc doesn't like that. It also does not remove null void functions with return. Done via: $ grep -rP --include=*.[ch] -l "return;\n}" net/ | \ xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }' with some cleanups by hand. Compile tested x86 allmodconfig only. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 4月, 2010 1 次提交
-
-
由 Eric Dumazet 提交于
replaces (skb->len - skb->data_len) occurrences by skb_headlen(skb) Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 4月, 2010 1 次提交
-
-
由 Sathya Perla 提交于
The promiscous cmd config code gives an impression that setting a port to promisc mode will unset the other port. This is not the case and is clarified with a comment. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 4月, 2010 2 次提交
-
-
由 FUJITA Tomonori 提交于
benet driver wrongly assumes that zero is an invalid dma address (calls dma_unmap_page for only non zero dma addresses). Zero is a valid dma address on some architectures. The dma length can be used here. Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 FUJITA Tomonori 提交于
The DMA API is preferred. Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 4月, 2010 1 次提交
-
-
由 Jiri Pirko 提交于
Converts the list and the core manipulating with it to be the same as uc_list. +uses two functions for adding/removing mc address (normal and "global" variant) instead of a function parameter. +removes dev_mcast.c completely. +exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for manipulation with lists on a sandbox (used in bonding and 80211 drivers) Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 4月, 2010 4 次提交
-
-
由 Sarveshwar Bandi 提交于
- Patch adds support to enable PCI SRIOV in the driver and changes to handle initialization of PCI virtual functions. - Function handler to change mac addresses for VF from its corresponding PF. Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
vlan traffic on big endian architecture is broken. Need to swap the vid before giving packet to stack. This patch fixes it. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Flashing is broken on big endian architectures like ppc. This patch fixes it. From: Naresh G <nareshg@serverengines.com> Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 31 3月, 2010 1 次提交
-
-
由 Eric Dumazet 提交于
eth_type_trans(skb, netdev) does the "skb->dev = netdev;" initialization, we can remove it from various network drivers. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 3月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: NTejun Heo <tj@kernel.org> Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
-
- 27 3月, 2010 1 次提交
-
-
由 wzt wzt 提交于
Fix the following warnings: be_ethtool.c:493: warning: integer constant is too large for 'long' type be_ethtool.c:493: warning: integer constant is too large for 'long' type Signed-off-by: NZhitong Wang <zhitong.wangzt@alibaba-inc.com> Acked-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 3月, 2010 1 次提交
-
-
由 Frans Pop 提交于
Signed-off-by: NFrans Pop <elendil@planet.nl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 3月, 2010 2 次提交
-
-
由 Sathya Perla 提交于
The first wrb seen by tx compl processing does not have a dma handle in it. Currently, pci_unmap_single() is attempted on this wrb and pci_unmap_page() on the rest. So, pci_unmap_page() gets incorrectly called on the dma hdl of skb->data (that was mapped using map_single()). This patch fixes this issue. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 3月, 2010 1 次提交
-
-
由 Ajit Khaparde 提交于
The request to create an mccq was being dispatched without doing a byte swap of num_pages. This byte swap is necessary for Big Endian systems like PPC. Not having this fix leads mccq create to fail on BE ASICs running newer version of firmware, thereby causing driver initialization failure. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 3月, 2010 2 次提交
-
-
由 Ajit Khaparde 提交于
This patch cleans up some unused code from be_load_fw(). Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
When PCI functions are virtuialized in applications by assigning PCI functions to VM (PCI passthrough), the be2net driver in the VM sees a different function number. So, use of PCI function number in any calculation will break existing code. This patch takes care of it. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 3月, 2010 1 次提交
-
-
由 Sarveshwar Bandi 提交于
Adding code to update NCSI section while updating firmware on the controller. Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 3月, 2010 1 次提交
-
-
由 Sathya Perla 提交于
In tx/mcc polling, napi_complete() is being incorrectly called before reaping tx completions. This can cause tx compl processing to be scheduled on another cpu concurrently which can result in a panic. This if fixed by calling napi complete() after tx/mcc compl processing but before re-enabling interrupts (via a cq notify). Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 2月, 2010 1 次提交
-
-
由 Jiri Pirko 提交于
Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 2月, 2010 3 次提交
-
-
由 Ajit Khaparde 提交于
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
For certain skews of the BE adapter, H/W Tx and Rx counters could be common for more than one interface. Add Tx and Rx counters in the adapter structure (to maintain stats on a per interfae basis). Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 2月, 2010 1 次提交
-
-
由 Sathya Perla 提交于
be2net: free tx buffers when completions never arrive In cases like when a pci device is disconnected on an error, pending tx completions will never arrive. Unmap and free such buffers in the tx cleanup path. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 2月, 2010 4 次提交
-
-
由 Sathya Perla 提交于
Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
The flush compl (compl with numfrags == 0; no data) is rcvd from hw to indicate completion of RXQ destory operation. Fix the RX path to not process it as RX data. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
When an MCC cmd is issued (via a netdev/ethtool op) while the device is not open, the MCC CQ gets processed but the EQ is not processed (as isr is not registered.) This can cause the EQ to become full. So, while the device is not open, CQ must not be re-armed to prevent EQ entries. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
Introduce unlikely() for skb alloc failure and vlanf checks... Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 2月, 2010 1 次提交
-
-
由 Ajit Khaparde 提交于
Before sending a command to the ASIC, set version properly. This is necessary for the ARM firmware to send correct data to the driver. This also fixes a bug in certain skews of the ASIC where the statistics are misreported. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 2月, 2010 1 次提交
-
-
由 Sathya Perla 提交于
The code has been tested on IBM pSeries server. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 2月, 2010 5 次提交
-
-
由 Ajit Khaparde 提交于
The offset to read the eeprom data was missing and wrong eeprom data was being dumped. This patch fixes this. >From Suresh R <sureshr@serverengines.com> Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Since the driver is supporting multiple generations of the ASIC don't mention any ASIC generation number. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Since the driver is supporting multiple generations of the ASIC remove ASIC generation information from the driver description. This information is displayed by modinfo. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
In certain skews the ASIC can support only 16 vlans per interface. Once the limit is crossed, the ASIC is programmed in vlan promiscuous mode. Switch off the vlan promiscuous mode once the number of vlans falls back to the max vlans supported. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Couple of code optimizations in the Rx path (to avoid a memset). From: Sathya P <sathyap@serverengines.com> Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-