The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since the only caller of this function doesn't care about the return
value anymore let's just remove it.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If we have devices set as to be connected we should connect to them even
during normal discovery if we get a connectable advertising event. If we
also have HCI_CONNECTABLE set we should connect ADV_DIRECT_IND events
even to devices that we don't have in our pend_le_conns list. This patch
implements such behavior by passing the advertising report type to
check_pending_le_conn() and calls that function regardless of what type
of scanning we are doing.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When we get an LE connection complete event we should restart background
scanning if there are any devices needing it. So far the code was only
making the decision based on whether the completed connection had any
stored parameters or not. This patch ensures that we trigger background
scanning always when necessary.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When we establish connections as a consequence of receiving an
advertising report it makes no sense to wait the normal 20 second LE
connection timeout. This patch modifies the hci_connect_le function to
take an extra timeout value and uses a lower 2 second timeout for the
auto-connection case. This timeout is intentionally chosen to be just a
bit higher than the 1.28 second timeout that High Duty Cycle Advertising
uses.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

During the setup phase of a controller, the Bluetooth address will be
read and to have that original address available for later use, store
it as setup address.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The HCI event callbacks have grown over the last years and some
functions handle status checking different than others. For the
simple ones, check the status at the beginning and exit if an
error with the HCI command occured.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

If a found device is marked as blocked while doing passive LE scanning,
neither report it nor try to connect to it.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Instead of looking through the entire list of entries we can more
efficiently use the new hci_pend_le_action_lookup() function to look up
entries specifically in the pend_le_reports list. Since the search is
now limited to the right list we can also remove an unnecessary check
for list_empty() before the lookup.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This is the last place using hci_pend_le_conn_add() and we can more
just as simply manipulate the list directly here.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since params->action is used for both the pend_le_conns and
pend_le_reports lists we can simplify the adding and deleting of the
lists considerably. For example, when deleting entries in most
situations we no-longer need to check the auto_connect value but can
directly proceed with calling list_del_init on param->action (which is
safe even if the entry is not part of any list).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If we're doing passive scanning we shouldn't proceed with any of the
code that deals with active scanning (pending reports, etc.). This patch
fixes a missing return statement for the passive scanning section in the
process_adv_report() function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since we only store entries with identity addresses in the
le_conn_params and pend_le_conns lists we can avoid unnecessary lookups
by checking for an identity address before diving into the lists
themselves.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If a device is in the pend_le_conns list it cannot at the same time also
have the need to be notified through mgmt_device_found. By making
check_pending_le_conn return whether it found an entry or not we can
avoid unnecessary checks in process_adv_report().
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When processing passive scanning results we need the resolved identity
address both in check_pending_le_conn() as well as later in
process_adv_report(). Since process_adv_report() calls
check_pending_le_conn() we can simply resolve the IRK earlier in the
function and thereby eliminate a second lookup.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When we're scanning for specific devices that use an RPA we need to
convert the RPA to the identity address before looking up the entry in
the connection parameters. This patch adds the necessary code to do this
in the process_adv_report() function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If we have one or more devices with HCI_AUTO_CONN_REPORT we should do
background scanning and emit mgmt_device_found events. This patch
modifies the hci_update_background_scan() function to extend the
conditions needed to trigger scanning, and adds the necessary code to
process_adv_report() to emit mgmt_device_found events.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The calling functions of mgmt_new_conn_param have more information about
the parameters, such as whether the kernel is tracking them or not. It
makes therefore sense to have them pass an initial store_hint value to
the mgmt_new_conn_param function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We should update any stored connection parameters when we receive the LE
Remote Connection Parameter Request HCI event. This patch adds the
necessary code to the function that handles the event.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Unlike BR/EDR we cannot reject LE connections of blocked devices but
have to do it as soon as we get a LE Connection Complete event. The
patch adds a blacklist check to the hci_le_conn_complete_evt function
and drops all connections for blocked devices.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch introduces a new Mgmt event called "New Connection Parameter".
This event indicates to userspace the connection parameters values the
remote device requested.

The user may store these values and load them into kernel. This way, next
time a connection is established to that device, the kernel will use those
parameters values instead of the default ones.

This event is sent when the remote device requests new connection
parameters through connection parameter update procedure. This event is
not sent for slave connections.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for LE Connection Parameters Request Link
Layer control procedure introduced in Core spec 4.1. This procedure
allows a Peripheral or Central to update the Link Layer connection
parameters of an established connection.

Regarding the acceptance of connection parameters, the LL procedure
follows the same approach of L2CAP procedure (see l2cap_conn_param_
update_req function). We accept any connection parameters values as
long as they are within the valid range.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There are certain subtle differences in behavior when we're encrypted
with the STK, such as allowing re-encryption even though the security
level stays the same. Because of this, add a flag to track whether we're
encrypted with an STK or not.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Device Found events of the management interface should indicate if
it is possible to connect to a remote device or if it is broadcaster
only advertising. To allow this differentation the Not Connectable flag
is introduced that will be set when it is known that a device can not
be connected.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.

This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The advertising data and scan response data are merged in the wrong
order. It should be advertsing data first and then scan response data
and not the other way around.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org # 3.16

This is to support the Motorola HF850 carkit which reports the error
code 0x10 for an eSCO attempt, even though it advertises eSCO support.

With this patch we will retry with a SCO connection, which succeeds.
Signed-off-by: NNick Pelly <npelly@google.com>
Signed-off-by: NKiran Kumar Raparthy <kiran.kumar@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for storing the local and piconet clock values
from the HCI_Read_Clock command response to the hci_dev and hci_conn
structs. This will be later used in another patch to implement support
for the Get Clock Info mgmt command.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since the link_mode member of the hci_conn struct is a bit field and we
already have a flags member as well it makes sense to merge these two
together. This patch moves all used link_mode bits into corresponding
flags. To keep backwards compatibility with user space we still need to
provide a get_link_mode() helper function for the ioctl's that expect a
link_mode style value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There's no point in having boolean variables in the hci_conn struct
since it already has a flags member. This patch converts the flush_key
member into a proper flag.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Instead of waiting for a disconnection to occur to remove a debug key
simply never store it in the list to begin with. This means we can also
remove the debug keys check when looking up keys in
hci_link_key_request_evt().
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We're planning to add a flag to actively use debug keys in addition to
simply just accepting them, which makes the current generically named
DEBUG_KEYS flag a bit confusing. Since the flag in practice affects
whether the kernel keeps debug keys around or not rename it to
HCI_KEEP_DEBUG_KEYS.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There are two callers of hci_add_link_key(). The first one is the HCI
Link Key Notification event and the second one the mgmt code that
receives a list of link keys from user space. Previously we've had the
hci_add_link_key() function being responsible for also emitting a mgmt
signal but for the latter use case this should not happen. Because of
this a rather awkward new_key paramter has been passed to the function.

This patch moves the mgmt event sending out from the hci_add_link_key()
function, thereby making the code a bit more understandable.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For all incoming LE connections, the minimum and maximum connection
interval is a value that should be copied from the controller default
values. This allows to properly check if the resulting connection
interval of a newly established connection is in the range we are
expecting.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When the LE controller changes its connection parameters, it will send
a connection parameter update event. Make sure that the new set of
parameters are stored in hci_conn struct and thus will properly update
the previous values retrieved from the connection complete event.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The LE connection parameters are needed later on to be able to decide
if it is required to trigger connection update procedures. So when the
connection has been established successfully, store the current used
parameters in hci_conn struct.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Create a CoC dynamically instead of one fixed channel for communication
to peer devices.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>