If DMA is unsupported ->ide_dma_check should disable DMA.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

All users of ->mmio == 1 are gone so convert ->mmio into flag.

Noticed by Alan Cox.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add ide_use_fast_pio() helper for use by host drivers

* add DMA capability and hwif->autodma checks to ide_use_dma()

  - au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)

    [ for the IT8211/2 in SMART mode this check shouldn't be made but since
      in it821x_fixups() we set DMA bit explicitly:

               if(strstr(id->model, "Integrated Technology Express")) {
                       /* In raid mode the ident block is slightly buggy
                          We need to set the bits so that the IDE layer knows
                          LBA28. LBA48 and DMA ar valid */
                       id->capability |= 3;            /* LBA28, DMA */

       we are better off using generic helper if we can ]

  - ide-cris driver didn't set ->autodma

    [ before the patch hwif->autodma was only checked in the chipset specific
      hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
      function so there no behavior change here ]

v2:
* updated patch description (thanks to Alan Cox for the feedback)

v3:
* updated for scc_pata driver
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

In cmd64x, siimage and scc_pata drivers:
* don't set drive->init_speed as it should be already
  set by successful execution of ide_set_xfer_rate()
* use hwif->speedproc functions directly

Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate).

v2:
* updated for scc_pata driver
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* remove bogus comment for sis5513_config_xfer_rate()
* there is no need to call config_drive_art_rwp() because
  it is called by config_art_rwp_pio()
* remove needless wrapper
* remove stale "TODO" comment
  (IDE core should provide generic tuning code)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* disable DMA masks if no_piix_dma is set and remove now
  not needed no_piix_dma_check from piix_config_drive_for_dma()
* there is no need to read register 0x55 in init_hwif_piix()
* move cable detection code to piix_cable_detect()
* remove unreachable 82371MX code from init_hwif_piix()
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* remove redundant svwks_ide_dma_end() [ __ide_dma_end() is used by default ]
* remove init_dma_svwks() so the default ide_setup_dma() function is used
  [ init_setup_csb6() takes care of not initializing disabled channels ]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* BUG() on unknown DMA mode in cs5530_config_dma()
* there is no need to call hwif->ide_dma_host_{off,on}() in
  cs5530_config_dma() because hwif->ide_dma_host_{off,on}()
  is called by hwif->ide_dma_off_{quietly,on}()
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

->init_dma() cannot be called with dmabase == 0
(see drivers/ide/setup-pci.c)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

In drivers/ide/Kconfig BLK_DEV_TRM290 depends on
BLK_DEV_IDEDMA_PCI (on which is BLK_DEV_IDEDMA dependant on).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

'speed' is always equal to 'mode' when ide_config_drive_speed() is called
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

CONFIG_PDC202XX_MASTER config option doesn't exist
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This is the patch (based on 2.6.19-rc4) for PATA controller of
Toshiba Cell reference set(Celleb). The reference set consists
of Cell, 512MB memory, Super Companion Chip(SCC) and some
peripherals such as HDD, GbE, etc. You can see brief explanation
and picture of Cell reference set at following URLs.

    http://www.toshiba.co.jp/about/press/2005_09/pr2001.htm
    http://cell-industries.com/toshiba_announces.php

We use a drivers/ide driver because its design is more suitable for
SCC IDE controller than libata driver. Since SCC supports only 32bit
read/write, we must override many callbacks of ata_port_operations
by modifying generic helpers. Each time the libata common code is
updated, we must update those modified helpers. It is very hard for us.
But we will try to implement the libata driver as needed.

Signed-off-by: Kou Ishizaki <kou.ishizaki at toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi at toshiba.co.jp>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix a number of issues with the DMA support code:

- driver claims support for all SW/MW DMA modes while supporting only MWDMA2;

- ide_dma_check() method tries to enable DMA on the "known good" drives which
  don't support MWDMA2;

- ide_dma_on() method upon failure to set drive to MWDMA2 re-tunes already
  tuned PIO mode and calls ide_dma_off() method instead of returning error;

- ide_dma_off() method sets drive->current_speed while it doesn't actually
  change (only the PIO timings are re-loaded into the chip's registers);

- init_hwif() method forcibly sets/resets both "drive DMA capable" bits while
  this is properly handled by ide_dma_{on,off}() methods being called later...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix the driver's tuneproc() method to always set the PIO mode requested and not
pick the best possible one, rename it to pdc202xx_tune_drive(), and change the
calls to it accordingly; remove the preceding comment which has nothing to do
with the code.

Sergei Shtylyov wrote:
>     The tuneproc() method should take arg 255 for auto-selecting the best PIO
> mode, not 5 as it did here + this driver's method always auto-selected instead
> of setting the mode it's been told to -- issue typical to drivers/ide/...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix two typos found by SiI680A documentation check.  They caused the taskfile
transfer overclocking:

- in PIO mode 1 as 0x2283 must be used for both data and taskfile transfers;

- in PIO mode 2 as data and taskfile timings are swapped when writing to the
  MMIO regs.

Fix coding style and trailing whitespace in enclosing statements while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

 drivers/ide/pci/siimage.c |   59 ++++++++++++++++++++++------------------------
 1 file changed, 29 insertions(+), 30 deletions(-)

patch 2/2:
  Remove clearing bmdma status from cdrom_decode_status() since ATA devices
  might need it as well.

  (http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94)
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
  hwif->ide_dma_clear_irq for Intel ICHx controllers.

Revised per Alan, Sergei and Bart's advice.

Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

A ZIP or similar with unformatted media will cause crashes when attempts
are made to read/write it in some cases. This is because bs_factor is
zero and we divide by it causing an oops.

As the size of a non-accessible/non-existant media is really a bit of a
zen question it doesn't matter if non-existant media is 512 bytes per
sector or zero. Setting it to 1 causes us to generate 512 bytes/sector
accesses and error properly.

Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh)
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* atiixp: if DMA can't be used atiixp_config_drive_for_dma() should return 0,
  atiixp_dma_check() will tune the correct PIO mode anyway

* jmicron: if DMA can't be used config_chipset_for_dma() should return 0,
  micron_config_drive_for_dma() will tune the correct PIO mode anyway

  config_jmicron_chipset_for_pio(drive, !speed) doesn't program
  device transfer mode for speed != 0 (only wastes some CPU cycles
  on ide_get_best_pio_mode() call) so remove it

* triflex: if DMA can't be used triflex_config_drive_for_dma() should return 0,
  triflex_config_drive_xfer_rate() will tune correct PIO mode anyway

Above changes also fix (theoretical) issue when ->speedproc fails to set
device transfer mode (i.e. when ide_config_drive_speed() fails to program it)
but one of DMA transfer modes is already enabled on the device by the BIOS.
In such scenario ide_dma_enable() will incorrectly return true statement
and ->ide_dma_check will try to enable DMA on the device.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* remember to clear reg2 bits for the current device before setting mode
* remove no longer needed hpt34x_clear_chipset()
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there.  Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.

To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.

Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm.  I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Many struct file_operations in the kernel can be "const".  Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data.  In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bug: pnx8550 code creates directory but resets ->nlink to 1.

create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds the module name to all PCI drivers, if they are built into the
kernel or not.  It will show up in /sys/modules/MODULE_NAME/drivers/

It also fixes up the IDE core, which was calling __pci_register_driver()
directly.

Cc: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/ide/ide-acpi.c: In function 'ide_acpi_get_timing':
drivers/ide/ide-acpi.c:537: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'long unsigned int'
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch implements ACPI integration for generic IDE devices.
The ACPI spec mandates that some methods are called during suspend and
resume. And consequently there most modern Laptops cannot resume
properly without it.

According to the spec, we should call '_GTM' (Get Timing) upon suspend
to store the current IDE adapter settings.
Upon resume we should call '_STM' (Set Timing) to initialize the
adapter with the stored settings; afterwards '_GTF' (Get Taskfile)
should be called which returns a buffer with some IDE initialisation
commands. Those commands should be passed to the drive.

There are two module params which control the behaviour of this patch:

'ide=noacpi'
	Do not call any ACPI methods (Disables any ACPI method calls)
'ide=acpigtf'
	Enable execution of _GTF methods upon resume.
	Has no effect if 'ide=noacpi' is set.
'ide=acpionboot'
	Enable execution of ACPI methods during boot.
	This might be required on some machines if 'ide=acpigtf' is
	selected as some machines modify the _GTF information
	depending on the drive identification passed down with _STM.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On Thursday 11 January 2007 23:17, Bartlomiej Zolnierkiewicz wrote:
> 
> My working IDE tree (against Linus' tree) now resides here:
> 
> 	http://kernel.org/pub/linux/kernel/people/bart/pata-2.6/patches/

Bart, here's a driver I've been keeping out-of-tree for the past couple
of years.  This is for the Delking/Lexar/ASKA/etc.. 32-bit cardbus IDE
CompactFlash adapter card.

It's probably way out of sync with the latest driver model (??), but it
still builds/works.  I'm not interested in doing much of a rewrite, other
than for libata someday, as I no longer use the card myself.

But lots of other people do seem to use it, so it might be nice to see it
"in-tree".
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* set ATAPI/IORDY/TIME bits correctly in it8213_tuneproc()
* fix UDMA/MWDMA/SWDMA masks in it8213_init_hwif()
* in it8213_tune_chipset() SWDMA2 mode should be used instead of MWDMA0
* backport various fixes from piix/slc90e66 drivers:
  - in it8213_tuneproc() the highest possible PIO mode is PIO4 (not PIO5)
  - clear ATAPI/IORDY/TIME bits before setting them also for slave device
  - use ->speedproc in it8213_config_drive_for_dma()
  - don't try to tune PIO in config_chipset_for_pio()
  - simplify is_slave calculation in it8213_tuneproc()
  - misc cleanups
* fix it8213_ratemask() and it8213_tuneproc() comments
* simplify it8213_init_hwif()
* remove init_chipset_it8213()
* add missing Copyrights and update MODULE_AUTHOR()
* CodingStyle cleanups
* remove dead code

v2:
* PCI_DEVICE_ID_ITE_8213 is only defined in -mm kernels,
  so just use PCI Device ID (0x8213) directly
* fix ->ultra_mask incorrectly changed to 0x3f in v1 version of the patch
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

From: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NAndrew Morton <akpm@osdl.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This is the driver for the Toshiba TC86C001 GOKU-S PCI IDE controller,
completely reworked from the original brain-damaged Toshiba's 2.4 version.

This single channel UltraDMA/66 controller is very simple in programming,
yet Toshiba managed to plant many interesting bugs in it.  The particularly
nasty "limitation 5" (as they call the errata) caused me to abuse the IDE
core in a possibly most interesting way so far.  However, this is still
better than the #ifdef mess in drivers/ide/ide-io.c that the original
version included (well, it had much more mess)...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAlan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fold check_in_drive_lists() into quirkproc() handler in both PDC202xx
drivers-- this function was never called with a list other than
pdc_quirk_drives and was a bad example of code overall...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>