"VendorID"   "DeviceID"  "SubsystemVendor ID"   "SubsystemDevice ID"  Cisco Branding String
0x1000         0x97           0x1137                 0x154           Cisco 9300-8i 12Gbps SAS HBA
0x1000         0x97           0x1137                 0x155           Cisco 12G Modular SAS Pass through Controller
0x1000         0x97           0x1137                 0x156           UCS C3X60 12G SAS Pass through Controller
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

mpt3sas: Return host busy error status to SML when DMA mapping of scatter gather list fails for a SCSI command

scsi_dma_map API will return a negative value (i.e. -ENOMEM)
if DMA mapping of sg lists fails and zero if the sg list in the
SCSI cmd is NULL. But drivers doesn't handled sg list DMA mapping
failure case properly.

So, Updated the code to return host busy error status to SCSI MID Layer(SML),
when DMA mapping of scatter gather list fails for a SCSI command.
So that SML will retry this SCSI cmd after some time.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

For any SCSI command, if the driver receives
IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then
that command will be completed with DID_RESET host status.

The definition of this log info value is
"Virtual IO has failed and has to be retried".

Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.
With this log info value, firmware informs the driver to retry the
failed IO command infinite times, so to provide some time for the
firmware to discover the reinserted drive successfully instated of
just retrying failed command for five times(doesn't giving enough
time for firmware to complete the drive discovery) and failing the
IO permanently even though drive came back successfully.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Below are the new changes to MPI 2.5 Rev K(2.5.6) specification and 2.00.35
header files

1) Added a minimum size requirement for target mode command buffers.

2) Added MinMSIxIndex and MaxMSIxIndex fields to CommandBufferPostBase
   Request.

3) For BIOS Page 1, added SSUTimeout field, and added Product Name String
   Format bits to the BiosOptions field
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Add the following OEM's branding to the mpt3sas driver.

"VendorID"   "DeviceID"  "SubsystemVendor ID"   "SubsystemDevice ID"  Cisco Branding String
0x1000         0x97         SVID = 0x1137             0x014C          Cisco 9300-8E 12G SAS HBA
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Added the following Dell branding to the mpt3sas driver.

"VendorID"   "DeviceID"  "SubsystemVendor ID"  "SubsystemDevice ID"  Dell Branding String
0x1000        0x0097          0x1028                 0x1F46            DELL 12Gbps HBA
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Following is the change set,

1. Added more defines for the BiosOptions field of MPI2_CONFIG_PAGE_BIOS_1.

2. Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC definition.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

This Patch will provide more details of the devices such as slot number,
enclosure logical id, enclosure level & connector name in the following
scenarios,

- When end device is added in the topology,

- When the end device is removed from the setup,

- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during
  error handling,

- When any command to the device fails with Sense key Hardware error or Medium
  error or Unit Attention,

- When firmware returns device error or device not ready status for the end
  device,

- When a Predicted fault is detected on an end device.

This information can be used by the user to identify the location of the
desired drive in the topology.

Driver will get these information by reading the sas device page0.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Update MPI 2.5 Release: MPI 2.5 Rev I (2.5.4) specification and 2.00.33 header
files

Below is the change set from the MPI specification for I Rev

1) Added Base Enclosure Level bit to the Flags field of Manufacturing Page 7.

2) Updated description of the MaxTargetPortConnectTime field of SAS IO Unit
   Page 1.

3) Added EnclosureLevel and ConnectorName fields to SAS Device Page 0. Also,
   added EnclosureLevel and ConnectorName Valid bit to the Flags field.

4) Added EnclosureLevel field to SAS Enclosure Page 0. Also, added
   EnclosureLevel Valid bit to the Flags field.

5) Added value for BIOS image to HashImageType.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

During hot-plugging of a disk(having a flaky link), the disk addition
stops and any further disk addition or removal doesn't happen on that
controller.

This is because, when driver receives DELAY_NOT_RESPONDING event for a disk
while it is undergoing addition at the SCSI Transport layer, the driver
would block the I/O to that disk resulting in a deadlock. i.e the disk
addition work couldn't be completed at the SCSI Transport Layer as it
can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as
I/Os are blocked to this drive. Also any subsequent device removal
(TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be
processed as they are in the queue to get processed after disk addition
event.

Description of Change:
Don't block the drive when drive addition is under the control of SML.
So that SML won't be blocked of issuing the device dicovery commands
(such as Inquiry, Report LUNs etc).
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

mpt3sas: Get IOC_FACTS information using handshake protocol only after HBA card gets into READY or Operational state.

Driver initialization fails if driver tries to send IOC facts request message
when the IOC is in reset or in a fault state.

This patch will make sure that

 1.Driver to send IOC facts request message only if HBA is in operational or
   ready state.

 2.If IOC is in fault state, a diagnostic reset would be issued.

 3.If IOC is in reset state then driver will wait for 10 seconds to exit out
   of reset state.  If the HBA continues to be in reset state, then the HBA
   wouldn't be claimed by the driver.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to
up-to 96.

Following are changes that are done in this patch

1. This feature is enabled only for SAS3 C0 and higher revision cards and also
only when reply post free queue count is greater than 8.

2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces
are used. MSI-X index numbered from 0 to 7 use the first
SupplementalReplyPostHostIndex system interface to update its corresponding
ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the
second SupplementalReplyPostHostIndex system interface and so on. These 12
SuppementalReplyPostHostIndex system interfaces address are saved in the array
replyPostRegisterIndex[].

3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X
vectors. So MSIxIndex field in these register must contain a value between 0
and 7.

4. After processing the reply descriptors from a reply post free queues then
update the new reply post host index value in ReplyPostHostIndex field and
(msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex
register. The Address of this SupplementalReplyPostHostIndex register is
retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

We recently did some cleanup here and now the static checkers notice
that there is a missing error code when ioremap() fails.  Let's set it
to -ENOMEM.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

In the function storvsc_channel_init(), error code was not getting
set correctly in some of the failure cases. Fix this issue.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Allow WRITE_SAME for Windows10 and above hosts.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Use storage protocol version instead of vmbus protocol
version when determining storage capabilities.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Use correct defaults for values determined by protocol negotiation,
instead of resetting them with every scsi controller.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Currently we are making decisions based on vmbus protocol versions
that have been negotiated; use storage potocol versions instead.

[jejb: fold ARRAY_SIZE conversion suggested by Johannes Thumshirn
<jthumshirn@suse.de>
make vmstor_protocol static]
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Use a single value to track protocol versions to simplify
comparisons and to be consistent with vmbus version tracking.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Rather than look for sets of specific protocol versions,
make decisions based on ranges. This will be safer and require fewer changes
going forward as we add more storage protocol versions.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The queuecommand routine has a local dev pointer used for the
dev_* prints. The two prints that currently exist are tucked
under a debug define and thus can be left out. Use the actual
location instead of a local to avoid this warning.

This patch is intended to be applied after the "CXL Flash Error
Recovery and Superpipe" series.
Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

"port_sel" is a u64 so the shifting should also be a 64 bit shift.

Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The > should be >= or we read one element past the end of the array.

Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Add support for physical LUN segmentation (virtual LUNs) to device
driver supporting the IBM CXL Flash adapter. This patch allows user
space applications to virtually segment a physical LUN into N virtual
LUNs, taking advantage of the translation features provided by this
adapter.
Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: NMichael Neuling <mikey@neuling.org>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Add superpipe supporting infrastructure to device driver for the IBM CXL
Flash adapter. This patch allows userspace applications to take advantage
of the accelerated I/O features that this adapter provides and bypass the
traditional filesystem stack.
Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: NMichael Neuling <mikey@neuling.org>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Introduce support for enhanced I/O error handling.

A device state is added to track 3 possible states of the device:

Normal - the device is operating normally and is fully operational

Limbo - the device is in a reset/recovery scenario and its operational
        status is paused

Failed/terminating - the device has either failed to be reset/recovered
                     or is being terminated (removed); it is no longer
                     operational

All operations are allowed when the device is operating normally. When the
device transitions to limbo state, I/O must be paused. To help accomplish
this, a wait queue is introduced where existing and new threads can wait
until the device is no longer in limbo. When coming out of limbo, threads
need to check the state and error out gracefully when encountering the
failed state. When the device transitions to the failed/terminating state,
normal operations are no longer allowed. Only specially designated
operations related to graceful cleanup are permitted.
Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: NDaniel Axtens <dja@axtens.net>
Reviewed-by: NMichael Neuling <mikey@neuling.org>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

On certain conditions, login failures will just invoke
qla2x00_mark_device_lost() with the intend to do login again;
but if login_retry has been set already, that would fail to set the
relogin needed flag which is required to wakeup the DPC to retry.
Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Fix for memory leak when command is not found by firmware due to
mismatch in sp reference count.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Instead of resetting the adapter wait for the login to timeout
and retry. Resetting the adapter can cause extended path recovery
times.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

If an SRB is NULL but the handle is in range just drop the
command instead of also resetting the adapter. If the handle
is in range then the command was valid at some point and may
have been aborted. Resetting the adapter can lead to extended
recovery times in this case.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Aovid crashing the system in the scenario where firmware
just completes the command and it can not find the command
during abort mailbox processing. This scenario can lead to
sp reference counter being zero. Instead of crashing the
system, use WARN_ON to print warning in log file.
Signed-off-by: NHiral Patel <hiral.patel@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>