- 03 4月, 2009 1 次提交
-
-
由 Leubner, Achim 提交于
changes: - set aac_cache=2 as default value to avoid performance problem (Novell bugzilla #469922) - Dell/PERC controller boot problem fixed (RedHat bugzilla #457552) - WWN flag added to fix SLES10 SP1/SP2 drive detection problems - 64-bit support changes - DECLARE_PCI_DEVICE_TABLE macro added - controller type changes Signed-off-by: NAchim Leubner <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
- 03 5月, 2008 2 次提交
-
-
由 Mark Salyzyn 提交于
For firmware that supports the feature(s), add the ability to start or stop an array using the associated SCSI commands, to automatically manage the spin-up of an array on new I/O reporting back the appropriate check conditions and actions in cooperation with the normal timeout mechanisms and enable the blackout period management in the Firmware associated with the background spin-down of the arrays when the Firmware times out and deems the arrays as idle. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Mark Salyzyn 提交于
On some compile environments, warnings are produced regarding the usage of aac_logical_to_phys macro. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
- 20 4月, 2008 1 次提交
-
-
由 Tony Jones 提交于
It's big, but there doesn't seem to be a way to split it up smaller... Signed-off-by: NTony Jones <tonyj@suse.de> Signed-off-by: NKay Sievers <kay.sievers@vrfy.org> Cc: Roland Dreier <rolandd@cisco.com> Cc: Sean Hefty <sean.hefty@intel.com> Cc: Hal Rosenstock <hal.rosenstock@gmail.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 12 2月, 2008 1 次提交
-
-
由 Salyzyn, Mark 提交于
Added support for MSI utilizing the aacraid.msi=1 parameter. This patch adds some localized or like-minded janitor fixes. Since the default is disabled, there is no impact on the code paths unless the customer wishes to experiment with the MSI performance. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
- 24 1月, 2008 7 次提交
-
-
由 Salyzyn, Mark 提交于
The cards being added are supported in a limited sense already through family matching, but we needed to add some functionality to the driver to expose selectively the physical drives. These Physical drives are specifically marked to not be part of any array and thus are declared JBODs (Just a Bunch Of Drives) for generic SCSI access. We report that this is the second patch in a set of two, but merely depends on the stand-alone functionality of the first patch which adds in that case the ability to report a driver feature flag via sysfs. We leverage that functionality by reporting that this driver now supports this new JBOD feature for the controller so that the array management applications may react accordingly and guide the user as they manage the controller. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Salyzyn, Mark 提交于
I was amazed at how much embedded space was present in the aacraid driver source files. Just selected five files from the set to clean up for now and the attached patch swelled to 73K in size! - Removed trailing space or tabs - Removed spaces embedded within tabs - Replaced leading 8 spaces with tabs - Removed spaces before ) - Removed ClusterCommand as it was unused (noticed it as one triggered by above) - Replaced scsi_status comparison with 0x02, to compare against SAM_STATUS_CHECK_CONDITION. - Replaced a long series of spaces with tabs - Replaced some simple if...defined() with ifdef/ifndef Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Salyzyn, Mark 提交于
Added support to respond to enclosure service events (controller AIFs) to add, online or offline physical targets reported to sg. Also added online and offlining of arrays. Removed an automatic variable definition in a sub block that hid an earlier definition, determined to be inert as the sub-block use did not interfere. Bumped the driver versioning to stamp the addition of this feature. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Salyzyn, Mark 提交于
In experiments in the lab we managed to trigger an Adapter firmware panic (BlinkLED) coincidentally while several pass-through ioctl command from the management software were outstanding on a bug only present on a class of RAID Adapters that require a hardware reset rather than a commanded reset. The net result was an attempt to time out the management software command as if it came from the SCSI layer resulting in an OS panic. Adapters that use commanded reset, management commands are returned failed by the Adapter correctly. The adapter firmware panic that resulted in this condition was also resolved, and there were no adapters in the field with this specific firmware bug so we do not expect any field reports. This is a rare or unlikely corner condition, and no reports have ever been forwarded from the field. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Salyzyn, Mark 提交于
Big endian systems issues discovered in the aacraid driver. Somewhat reverses a patch from November 7th of last year that removed swap operations because they formerly were being assigned to an u8 array when they should have been assigned to an le32 array. This patch is largely inert for any little endian processor architecture. It resolves a bug in delivering the BlinkLED AIF event to registered applications when the adapter or associated hardware was reset due to ill health. A rare corner case occurrence, also largely unnoticed by any as it was a new (untested!) feature. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Salyzyn, Mark 提交于
Report the RAID level string for the SCSI device representing the array. Report is in /sys/class/scsi_device/#:#:#:#/device/level. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Salyzyn, Mark 提交于
aacraid.cache parameter, Disable Queue Flush commands: bit 0 - Disable FUA in WRITE SCSI commands bit 1 - Disable SYNCHRONIZE_CACHE SCSI command bit 2 - Disable only if Battery not protecting adapter supplied Cache e.g.: aacraid.cache=7 will disable the FUA and SYNCHRONIZE_CACHE commands if the adapter has reported that it's cache is battery backed up. This parameter permits experimentation with tradeoffs between performance and caching policy. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
- 12 1月, 2008 1 次提交
-
-
由 Salyzyn, Mark 提交于
As reported in http://bugzilla.kernel.org/show_bug.cgi?id=3D9133 it was discovered that the PERC line of controllers lacked a key 64 bit ScatterGather capable SCSI pass-through function. The adapters are still capable of 64 bit ScatterGather I/O commands, but these two can not be mixed. This problem was exacerbated by the introduction of the SCSI Generic access to the DASD physical devices. The fix for users before this patch is applied is aacraid.dacmode=3D0 on the kernel command line to disable 64 bit I/O. The enclosed patch introduces a new adapter quirk and tries to limp along by enabling pass-through in situations where memory is 32 bit addressable on 64 bit machines, or disable the pass-through functions altogether. I expect that the check for 32 bit addressable memory to be controversial in that it can be incorrect in non-Dell non-Intel systems that PERC would never be installed under, the alternative is to disable pass-through in all cases which could be reported as another regression. Pass-through is used for SCSI Generic access to the physical devices, or for the management applications to properly function. In systems where this patch has disabled pass-through because it is unsupportable in combination with I/O performance, the user can choose to enable pass-through by turning off dacmode (aacraid.dacmode=3D0) or limiting the discovered kernel memory (mem=3D4G) with an associated loss in runtime performance. If we chose instead to turn off 64 bit dacmode for the adapters with this quirk, then this would be reported as another regression. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
- 20 10月, 2007 1 次提交
-
-
由 Robert P. J. Day 提交于
Fix the various misspellings of "system", controller", "interrupt" and "[un]necessary". Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com> Signed-off-by: NAdrian Bunk <bunk@kernel.org>
-
- 13 10月, 2007 1 次提交
-
-
由 Andrew Morton 提交于
Too generic, clashes with ISDN. Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 27 7月, 2007 1 次提交
-
-
由 Salyzyn, Mark 提交于
Minor unimportant cuttings from the floor bundled in with a version stamp update. Only controversial change is the dropping of Alan Cox copyright on the nark.c module since that file has no code written by him in it. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 19 7月, 2007 1 次提交
-
-
由 Salyzyn, Mark 提交于
Report VPD inquiry page 0x80 with an unique array creation serial number (CUID). When an array is created, the metadata stored on the physical drives gets an unique serial number. This serial number remains constant through array morphing or migration to other controllers. This patch is a forward port and modification to survive morphing and migration operations, of a similar piece of (un-attributed author) code added to the SLES10 SP1 aacraid driver. To test the results of the patch, observe that /dev/disk/by-id/ entries will show up for the arrays resulting from the udev rules. Also, as per the udev rules, 'scsi_id -g -x -a -s /block/sd? -d /dev/sd?' will report the ID_SERIAL as constructed from the inquiry data. It was reported to me that the 'ADPT' leading the serial number was bad form, that the inquiry vendor field was enough to differentiate the storage uniquely. Subsequent search found that another Adaptec AAC based driver reported the 8 hex serial number only without such adornments, so dropped ADPT to match. Resubmitting the patch with this alteration. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 20 6月, 2007 1 次提交
-
-
由 Salyzyn, Mark 提交于
Support displaying long serial number information. Reuse sysfs handler internally as helper. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 18 6月, 2007 1 次提交
-
-
由 Salyzyn, Mark 提交于
Add the ability for an application to issue a hardware reset to the adapter via sysfs. Typical uses include restarting the adapter after it has been flashed. Bumped revision number for the driver and added a feature to periodically check the adapter's health (check_interval), update the adapter's concept of time (update_interval) and block checking/resetting of the adapter (check_reset). Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 24 5月, 2007 1 次提交
-
-
由 Jeff Garzik 提交于
Signed-off-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: N"Salyzyn, Mark" <mark_salyzyn@adaptec.com> Acked-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 23 5月, 2007 1 次提交
-
-
由 Salyzyn, Mark 提交于
Under some conditions associated with the unclean transition to kdump, the aacraid adapters will view the array as foreign and not export it to prevent access and data manipulation. The solution is to submit a commit configuration to export the devices since this is a expected behavior when transitioning to a kdump kernel. This patch adds the aacraid.reset_devices flag and when either this or the global reset_devices flag is set, ensures that a commit config is issued and extends the startup_timeout if it is set less than 5 minutes. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 22 5月, 2007 1 次提交
-
-
由 Salyzyn, Mark 提交于
Back in the beginning of last year we disabled mode page 8 and mode page 3f requests through device quirk bits instead of enhancing the driver to respond to these mode pages because there was no apparent added value. The Firmware that supports the new communication commands supports the ability to force a write around of the adapter cache on a command by command basis. In the attached patch we enable mode page 8 and 3f and spoof the results as needed in order to *convince* the layers above to submit writes with the FUA (Force Unit Attention) bit set if the file system or application requires it, if the Firmware supports the write through, or instead to submit a SYNCHRONIZE_CACHE if the Firmware does not. The added value here is for file systems that benefit from this functionality and for clustering or redundancy scenarios. Caveats: By convince, we are responding with a minimal short 3 byte content mode page 8, with only the data the SCSI layer needs and that we can fill confidently. Applications that require the customarily larger mode page 8 results may be confused by this(?). The FUA, or the SYNCHRONIZE_CACHE only affect the cache on the controller. Our firmware by default ensure that the underlying physical drives of the array have their cache turned off so normally this is not a problem. This attached patch is against current scsi-misc-2.6 and was unit tested on RHEL5. Since this is a feature enhancement, it should not be considered for any current stabilization efforts. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 17 5月, 2007 1 次提交
-
-
由 Salyzyn, Mark 提交于
[SCSI] aacraid: Correct sa platform support. (Was: [Bug 8469] Bad EIP value on pentium3 SMP kernel-2.6.21.1) http://bugzilla.kernel.org/show_bug.cgi?id=8469 As discussed in the bugzilla outlined below, we have an sa based (Mustang) RAID adapter on the system, a Dell PERC2/QC. Affected controllers are HP NetRAID, Adaptec AAC-364, Dell PERC2/QC or Adaptec 5400S. This problem coincides with the introduction of the adapter_comm and adapter_deliver platform functions (Message [PATCH 1/4] aacraid: rework communication support code, January 23 2007, which initially migrated to 2.6.21) The panic occurs with an uninitialized adapter_deliver platform function pointer. The enclosed patch, unmodified as tested by Rainer, solves the problem. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 01 4月, 2007 3 次提交
-
-
由 Salyzyn, Mark 提交于
The Adapter build date that is to be printed on instantiation was not displayed as a result of the supplemental adapter information structure not being in sync with the Firmware; the driver took an early test cycle version that had a miss-sized padded region at the head and the structure was not re-checked at the end of qualification. The Build Date was not a priority and is merely a cosmetic enhancement, and the wrong location for the start of the structure member would not induce any side-effect problems. We updated the structure to match the actual format, and added the TSID (Tech Support Identification) value print, should it be present, to the adapter instantiation announcements during driver load. This later enhancement should improve the relationship between Service folk & Tech Support if the printed value of the TSID found it's way into the circular file labeled G... Neither of these values show in sysfs (yet). Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Salyzyn, Mark 提交于
Just sweeping the floor clean in one spot. Some of these constants have never been used in the driver or in the firmware (and thus are meaningless). Triggered this patch because I discovered one of the unused constants was actually incorrect and figured it was better to clean them out than correct and update. There are no side effects at all regarding this patch, it is purely cosmetic. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Adrian Bunk 提交于
- proper prototypes for global code in aacraid.h - aac_rx_start_adapter() can now become static Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: N"Salyzyn, Mark" <mark_salyzyn@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 22 3月, 2007 1 次提交
-
-
由 Salyzyn, Mark 提交于
There is some residual cleanup of the last series of patches and the need to bump the revision number to draw the line in the sand. The cmd->SCp.phase is set in the aac_valid_context routine, then set again to the same value following it's return. The cmd->scsi_done is set twice in the aac_queuecommand routine. Free up the scsidev FILO in aac_probe_container as it is not needed further down the function in any case. Improve the efficiency of the abort handler kernel print parameters. Bump revision number of driver to approximate the equivalent in the Adaptec supplied version. Signed-off-by: NMark Salyzyn <aacraid@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 20 3月, 2007 3 次提交
-
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn, This set of fixes improve error handling stability of the driver. A popular manifestation of the problems is an NULL pointer reference in the interrupt handler when referencing portions of the scsi command context, or in the scsi_done handling when an offlined device is referenced. The aacraid driver currently does not get notification of orphaned command completions due to devices going offline. The driver also fails to handle the commands that are finished by the error handler, and thus can complete again later at the hands of the adapter causing situations of completion of an invalid scsi command context. Test Unit Ready calls abort assuming that the abort was successful, but are not, and thus when the interrupt from the adapter occurs, they reference invalid command contexts. We add in a TIMED_OUT flag to inform the aacraid FIB context that the interrupt service should merely release the driver resources and not complete the command up. We take advantage of this with the abort handler as well for select abortable commands. And we detect and react if a command that can not be aborted is currently still outstanding to the controller when reissued by the retry mechanism. Signed-off-by: NMark Haverkamp <markh@linux-foundation.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn, This patch is to resolve a namespace issue that will result from a patch expected in the future that adds a new interface; rationalized as correcting a long term issue where hw_fib, instead of hw_fib_va, refers to the virtual address space and hw_fib_pa refers to the physical address space. A small fragment of this patch also cleans up an unused variable that was close to the patch fragments. Signed-off-by: NMark Haverkamp <markh@linux-foundation.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn, This patch updates the adapter restart function to deal with some adapters that have specific IOP reset needs. Since the code for restarting the adapter was in two places, changed over to utilizing a platform function in one place. Signed-off-by: NMark Haverkamp <markh@linux-foundation.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 27 1月, 2007 3 次提交
-
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn, Replace all if/else packet formations with platform function calls. This is in recognition of the proliferation of read and write packet types, and in the need to migrate to up-and-coming packets for new products. Signed-off-by Mark Haverkamp <markh@linux-foundation.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn, Add in the NEMER/ARK physical register mapping, represented in up and coming products currently under test at Adaptec. Signed-off-by Mark Haverkamp <markh@linux-foundation.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn, Replace all if/else communication transports with a platform function call. This is in recognition of the need to migrate to up-and-coming transports. Currently the Linux driver does not support two available communication transports provided by our products, these will be added in future patches, and will expand the platform function set. Signed-off-by Mark Haverkamp <markh@linux-foundation.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 23 11月, 2006 1 次提交
-
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn: Version patch, update to reflect a rough estimate of the Adaptec build (2423) that coincides with the sources on kernel.org. Signed-off-by: NMark Haverkamp <markh@osdl.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 24 9月, 2006 2 次提交
-
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn: The only real difference between the rkt and rx platform modules is the offset of the message registers. This patch recognizes this similarity and simplifies the driver to reduce it's code footprint and to improve maintainability by reducing the code duplication. Visibly, the 'rkt.c' portion of this patch looks more complicated than it really is. View it as retaining the rkt-only specifics of the interface. Signed-off-by: NMark Haverkamp <markh@osdl.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn: Basically cleanup, nothing here will have an affect. Adjusting some error codes, removing superfluous definitions and code fragments. Signed-off-by: NMark Haverkamp <markh@osdl.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 20 8月, 2006 2 次提交
-
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn If the adapter is in blinkled (Firmware Assert) when error recovery timeout actions have been triggered, perform an adapter warm reset and restart the initialization. Signed-off-by: NMark Haverkamp <markh@osdl.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn If the adapter should be in a blinkled (Firmware Assert) state when the driver loads, we will perform a warm restart of the Adapter Firmware to see if we can rescue the adapter. Possible causes of a blinkled can occur on some early release motherboard BIOSes, transitory PCI bus problems on embedded systems or non-x86 based architectures, transitory startup failures of early release drives or transitory hardware failures; some of which can bite the adapter later at runtime. Future enhancements will include recovery during runtime. Fixed extra whitespace space issue. Signed-off-by: NMark Haverkamp <markh@osdl.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 20 6月, 2006 1 次提交
-
-
由 Mark Haverkamp 提交于
Received from Mark Salyzyn Spelling correction, orphaned comment removal & update branch name. Signed-off-by: NMark Haverkamp <markh@osdl.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 20 5月, 2006 1 次提交
-
-
由 Mark Haverkamp 提交于
Received From Mark Salyzyn The queue tracking is just not being used, not even for debugging. Information about outstanding commands can be acquired from the scsi structures. Signed-off-by: NMark Haverkamp <markh@osdl.org> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-