This drops another symbol dependency between setup.c and sprom.c which
will allow us to make SPROM code a separated module (and share it with
ARM).
Patch tested on Linksys WRT300N V1.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11360/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extra bcma buses may be totally different models, see following dump:
boardtype=0x0646
pci/1/1/boardtype=0x0545
pci/2/1/boardtype=0x62b
We need to detect them properly to allow drivers apply some board
specific hacks.

[ralf@linux-mips.org: folded in Rafal's fix.]
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/10028/
Patchwork: https://patchwork.linux-mips.org/patch/10048/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

[ralf@linux-mips.org: Fixed conflicts.]
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: Paul Walmsley <paul@pwsan.com>
Patchwork: https://patchwork.linux-mips.org/patch/8665/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

There are two reasons for having this header in the common place:
1) Simplifying drivers that read NVRAM entries. We will be able to
   safely call bcm47xx_nvram_* functions without #ifdef-s.
2) Getting NVRAM driver out of MIPS arch code. This is needed to support
   BCM5301X arch which also requires this NVRAM driver. Patch for that
   will follow once we get is reviewed.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: linux-soc@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8619/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Initializaion with memory allocator available will be much simpler, this
will allow cleanup in the bcma code.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8234/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is some general cleanup as well as preparing sprom.c to become a
standalone driver. We will need this for bcm53xx ARM arch support.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8232/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is required to split SoC bus init into two phases. The later one
(which includes scanning) should be called when kalloc is available.

Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.

Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.

The previous commit was 316cad5c [MIPS:
BCM47XX: make reboot more relaiable]
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: jogo@openwrt.org
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7545/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.

Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.

The previous commit was 316cad5c [MIPS:
BCM47XX: make reboot more relaiable]
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: jogo@openwrt.org
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7545/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

So far BCM47XX can only detect amount of HIGHMEM. It still requires
adding (registering) and well-testing before enabling by default.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7396/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The reboot on the BCM47XX SoCs is done, by setting the watchdog counter
to 1 and let it trigger a reboot, when it reaches 0. Some devices with
a BCM4705/BCM4785 SoC do not reboot when the counter is set to 1 and
decreased to 0 by the hardware. It looks like it works more reliable
when we set it to 3. As far as I understand the hardware, this should
not make any difference, but I do not have access to any documentation
for this SoC.
It is still not 100% reliable.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7488/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/6627/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The 1074K is a multiprocessing coherent processing system (CPS) based
on modified 74K cores. This patch makes the 1074K an actual unique
CPU type, instead of a 74K derivative, which it is not.
Signed-off-by: NSteven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6389/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The disabling of cpu_wait was done too early, before the detection was
done. This moves the code to a position where it actually works.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6352/

So far this adds support for one Netgear model only, but it's designed
and ready to add many more device. We could hopefully import database
from OpenWrt.
Support for SSB is currently disabled, because SSB doesn't implement IRQ
domain yet.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6300/

So far this is mostly just a proof of concept, database consists of a
single device. Creating a nice iterateable array wasn't an option
because devices have different amount of LEDs. And we don't want to
waste memory just because of support for a device with dozens on LEDs.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6299/

The BCM4706 has a problem with the CPU wait instruction. When r4k_wait
or r4k_wait_irqoff is used will just hang and not return from a
msleep(). Removing the cpu_wait functionality is a workaround for this
problem. The BCM4716 does not have this problem.

The BCM4706 SoC uses a MIPS 74K V4.9 CPU.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6288/

This will add the board name to the machine entry in /proc/cpuinfo.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5864/

Recently the output of "system type" in  /proc/cpuinfo was changed to
Broadcom BCM4730 (Some sample board), but it is better to just print
the SoC name in the "system type" entry. The board name will be added
in the machine entry later.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5865/

The ADM6996L switch and some Broadcom switches with two MII interfaces
like the BCM5325F connected to two MACs on the SoC, used on some
routers do not return a valid value when reading the PHY id register
and Linux thinks there is no PHY at all, but that is wrong.
This patch registers a fixed phy in the arch code and then searches it
when there is no other phy in the Ethernet driver code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Detect on which board this code is running based on some nvram
settings. This is needed to start board specific workarounds and
configure the leds and buttons which are on different gpios on every board.

This patches add some boards we have seen, but there are many more.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5840
Patchwork: https://patchwork.linux-mips.org/patch/5855/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The nvram functions are exported and used by some normal drivers. To
prevent name clashes with ofter parts of the kernel code add a bcm47xx_
prefix in front of the function names and the header file name.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4744/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

There are bcma based devices like the Linksys E2000 out there, which do
have one ieee80211 core, but no PCIe core and they are using no
prefixes for the sprom. In addition some values like boardtype are
stored without a prefix for the main SoC chip also when they have an
additional PCIe wifi chip with an own boardtype var on some devices.

The Ethernet addresses are now also read out correctly without a prefix
so calling bcm47xx_fill_sprom_ethernet is not needed any more.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4364Signed-off-by: NJohn Crispin <blogic@openwrt.org>

If there is no ieee80211 core on the devices like on the BCM4706 read
out the sprom and the other data without using a prefix.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4361Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The first thing bcm47xx_fill_sprom does is initialize (zero fill) the SPROM.  For
BCMA SOC, this wipes out any values previously read by bcm47xx_fill_sprom_ethernet
(see arch/mips/bcm47xx/setup.c - bcm47xx_get_sprom_bcma).  Move the initialization
of SPROM so it is called prior to filling in any values.
Signed-off-by: NNathan Hintz <nlhintz@hotmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Tested-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now the fetching of board data also uses nvram_read_u16 and not
simple_strtoul any more.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously the rev contained the revision read from the pci config
space and was used as board_rev in the wireless drivers. This is wrong
the board_rev is only fetched from the sprom accordingly to the open
source part of the Broadcom SDK and brcmsmac. This patch removes the
rev from the boardinfo structure and uses the board_rev attribute from
sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC
code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Tested-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On SoCs the sprom is often stored in nvram in the flashchip. This patch
registers a sprom fallback callback handler in bcma and provides the
sprom needed for this device.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the sprom parsing from nvram into sprom.c. There are all values
needed for sprom version 1 to 9 read from nvram and there are more
sanity checks added. This is based on the sprom parsing in the open
source part of the Broadcom SDK.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n.  Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Or else we get lots of variations on this:

arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'

scattered throughout the build.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

This patch add support for the bcma bus. Broadcom uses only Mips 74K
CPUs on the new SoC and on the old ons using ssb bus there are no Mips
74K CPUs.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prepare bcm47xx to support different System buses. Before adding
support for bcma it should be possible to build bcm47xx without the
need of ssb. With this patch bcm47xx does not directly contain a
ssb_bus, but a union contain all the supported system buses. As a SoC
just uses one system bus a union is a good choice.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Some members of the struct ssb_sprom where not filled with data available
in the NVRAM. Some attribute names in the NVRAM changed from SPROM version
3 to version 4. This patch was done by analyzing the the pci sprom parser
in the ssb code and some open source parts of the braodcom wireless driver
used on embedded devices.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2365/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We are generating the prefix based on the PCI bus address the device is
on. This is done like Broadcom does it in their code expect that the the
bus number is increased by one. In the SB bus implementation used by
Broadcom the SB bus emulates a PCI bus so the kernel sees one PCI bus
more then in our implementation. We do not handle prefixes like sb/1/
yet as they are only used on the new bus which is not implemented yet.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2364/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When an other SSB based device without an own SPROM is attached, using the
PCI bus to the main SSB based device, the data normally found in the SPROM
will be stored in the NVRAM on modern devices. The keys, to load the data
from the NVRAM, are all using some sort of prefix like pci/1/1/, pci/1/3/
or sb/1/ before the actual key. This patch extends bcm47xx_fill_sprom() to
make it possible to read out these values when some prefix was used.

The keys for the SPROM data used on the main chip does not have a prefix.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2363/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>