Fix the objtool build when cross-compiling a 64-bit kernel on a 32-bit
host.  This also simplifies read_retpoline_hints() a bit and makes its
implementation similar to most of the other annotation reading
functions.
Reported-by: NSven Joachim <svenjoac@gmx.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: b5bc2231 ("objtool: Add retpoline validation")
Link: http://lkml.kernel.org/r/2ca46c636c23aa9c9d57d53c75de4ee3ddf7a7df.1520380691.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Continue the switch table detection whack-a-mole.  Add a check to
distinguish KASAN data reads from switch data reads.  The switch jump
tables in .rodata have relocations associated with them.

This fixes the following warning:

  crypto/asymmetric_keys/x509_cert_parser.o: warning: objtool: x509_note_pkey_algo()+0xa4: sibling call from callable instruction with modified stack frame
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NArnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/d7c8853022ad47d158cb81e953a40469fc08a95e.1519784382.git.jpoimboe@redhat.com

David allowed retpolines in .init.text, except for modules, which will
trip up objtool retpoline validation, fix that.
Requested-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

David requested a objtool validation pass for CONFIG_RETPOLINE=y enabled
builds, where it validates no unannotated indirect  jumps or calls are
left.

Add an additional .discard.retpoline_safe section to allow annotating
the few indirect sites that are required and safe.
Requested-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: NDavid Woodhouse <dwmw@amazon.co.uk>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Use the existing global variables instead of passing them around and
creating duplicate global variables.
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Peter Zijlstra's patch for converting WARN() to use UD2 triggered a
bunch of false "unreachable instruction" warnings, which then triggered
a seg fault in ignore_unreachable_insn().

The seg fault happened when it tried to dereference a NULL 'insn->func'
pointer.  Thanks to static_cpu_has(), some functions can jump to a
non-function area in the .altinstr_aux section.  That breaks
ignore_unreachable_insn()'s assumption that it's always inside the
original function.

Make sure ignore_unreachable_insn() only follows jumps within the
current function.
Reported-by: NBorislav Petkov <bp@alien8.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kbuild test robot <fengguang.wu@intel.com>
Link: http://lkml.kernel.org/r/bace77a60d5af9b45eddb8f8fb9c776c8de657ef.1518130694.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Linus reported that GCC-7.3 generated a switch-table construct that
confused objtool. It turns out that, in particular due to KASAN, it is
possible to have unrelated .rodata usage in between the .rodata setup
for the switch-table and the following indirect jump.

The simple linear reverse search from the indirect jump would hit upon
the KASAN .rodata usage first and fail to find a switch_table,
resulting in a spurious 'sibling call with modified stack frame'
warning.

Fix this by creating a 'jump-stack' which we can 'unwind' during
reversal, thereby skipping over much of the in-between code.

This is not fool proof by any means, but is sufficient to make the
known cases work. Future work would be to construct more comprehensive
flow analysis code.
Reported-and-tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180208130232.GF25235@hirez.programming.kicks-ass.netSigned-off-by: NIngo Molnar <mingo@kernel.org>

Now that the previous patch gave objtool the ability to read retpoline
alternatives, it shows a new warning:

  arch/x86/entry/entry_64.o: warning: objtool: .entry_trampoline: don't know how to handle alternatives at end of section

This is due to the JMP_NOSPEC in entry_SYSCALL_64_trampoline().

Previously, objtool ignored this situation because it wasn't needed, and
it would have required a bit of extra code.  Now that this case exists,
add proper support for it.
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/2a30a3c2158af47d891a76e69bb1ef347e0443fd.1517284349.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Currently objtool requires all retpolines to be:

  a) patched in with alternatives; and

  b) annotated with ANNOTATE_NOSPEC_ALTERNATIVE.

If you forget to do both of the above, objtool segfaults trying to
dereference a NULL 'insn->call_dest' pointer.

Avoid that situation and print a more helpful error message:

  quirks.o: warning: objtool: efi_delete_dummy_variable()+0x99: unsupported intra-function call
  quirks.o: warning: objtool: If this is a retpoline, please patch it in with alternatives and annotate it with ANNOTATE_NOSPEC_ALTERNATIVE.

Future improvements can be made to make objtool smarter with respect to
retpolines, but this is a good incremental improvement for now.
Reported-and-tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/819e50b6d9c2e1a22e34c1a636c0b2057cc8c6e5.1517284349.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

In preparation for refactoring the usercopy checks to pass offset to
the hardened usercopy report, this renames report_usercopy() to the
more accurate usercopy_abort(), marks it as noreturn because it is,
adds a hopefully helpful comment for anyone investigating such reports,
makes the function available to the slab allocators, and adds new "detail"
and "offset" arguments.
Signed-off-by: NKees Cook <keescook@chromium.org>

Getting objtool to understand retpolines is going to be a bit of a
challenge.  For now, take advantage of the fact that retpolines are
patched in with alternatives.  Just read the original (sane)
non-alternative instruction, and ignore the patched-in retpoline.

This allows objtool to understand the control flow *around* the
retpoline, even if it can't yet follow what's inside.  This means the
ORC unwinder will fail to unwind from inside a retpoline, but will work
fine otherwise.
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: NDavid Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: gnomes@lxorguk.ukuu.org.uk
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: thomas.lendacky@amd.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kees Cook <keescook@google.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: https://lkml.kernel.org/r/1515707194-20531-3-git-send-email-dwmw@amazon.co.uk

A direct jump to a retpoline thunk is really an indirect jump in
disguise.  Change the objtool instruction type accordingly.

Objtool needs to know where indirect branches are so it can detect
switch statement jump tables.

This fixes a bunch of warnings with CONFIG_RETPOLINE like:

  arch/x86/events/intel/uncore_nhmex.o: warning: objtool: nhmex_rbox_msr_enable_event()+0x44: sibling call from callable instruction with modified stack frame
  kernel/signal.o: warning: objtool: copy_siginfo_to_user()+0x91: sibling call from callable instruction with modified stack frame
  ...
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: NDavid Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: gnomes@lxorguk.ukuu.org.uk
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: thomas.lendacky@amd.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kees Cook <keescook@google.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: https://lkml.kernel.org/r/1515707194-20531-2-git-send-email-dwmw@amazon.co.uk

When an error occurs before adding an allocated insn to the list, free
it before returning.
Signed-off-by: NKamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/336da800bf6070eae11f4e0a3b9ca64c27658114.1508430423.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

If asm code specifies an UNWIND_HINT_EMPTY hint, don't warn if the
section ends unexpectedly.  This can happen with the xen-head.S code
because the hypercall_page is "text" but it's all zeros.
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/ddafe199dd8797e40e3c2777373347eba1d65572.1505764066.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The kbuild bot reported the following warning with GCC 4.4 and a
randconfig:

  net/socket.o: warning: objtool: compat_sock_ioctl()+0x1083: stack state mismatch: cfa1=7+160 cfa2=-1+0

This is caused by another GCC non-optimization, where it backs up and
restores the stack pointer for no apparent reason:

    2f91:       48 89 e0                mov    %rsp,%rax
    2f94:       4c 89 e7                mov    %r12,%rdi
    2f97:       4c 89 f6                mov    %r14,%rsi
    2f9a:       ba 20 00 00 00          mov    $0x20,%edx
    2f9f:       48 89 c4                mov    %rax,%rsp

This issue would have been happily ignored before the following commit:

  dd88a0a0 ("objtool: Handle GCC stack pointer adjustment bug")

But now that objtool is paying attention to such stack pointer writes
to/from a register, it needs to understand them properly.  In this case
that means recognizing that the "mov %rsp, %rax" instruction is
potentially a backup of the stack pointer.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: dd88a0a0 ("objtool: Handle GCC stack pointer adjustment bug")
Link: http://lkml.kernel.org/r/8c7aa8e9a36fbbb6655d9d8e7cea58958c912da8.1505942196.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Arnd Bergmann reported the following warning with GCC 7.1.1:

  fs/fs_pin.o: warning: objtool: pin_kill()+0x139: stack state mismatch: cfa1=7+88 cfa2=7+96

And the kbuild robot reported the following warnings with GCC 5.4.1:

  fs/fs_pin.o: warning: objtool: pin_kill()+0x182: return with modified stack frame
  fs/quota/dquot.o: warning: objtool: dquot_alloc_inode()+0x140: stack state mismatch: cfa1=7+120 cfa2=7+128
  fs/quota/dquot.o: warning: objtool: dquot_free_inode()+0x11a: stack state mismatch: cfa1=7+112 cfa2=7+120

Those warnings are caused by an unusual GCC non-optimization where it
uses an intermediate register to adjust the stack pointer.  It does:

  lea    0x8(%rsp), %rcx
  ...
  mov    %rcx, %rsp

Instead of the obvious:

  add    $0x8, %rsp

It makes no sense to use an intermediate register, so I opened a GCC bug
to track it:

  https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81813

But it's not exactly a high-priority bug and it looks like we'll be
stuck with this issue for a while.  So for now we have to track register
values when they're loaded with stack pointer offsets.

This is kind of a big workaround for a tiny problem, but c'est la vie.
I hope to eventually create a GCC plugin to implement a big chunk of
objtool's functionality.  Hopefully at that point we'll be able to
remove of a lot of these GCC-isms from the objtool code.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/6a41a96884c725e7f05413bb7df40cfe824b2444.1504028945.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

When GCC adds NOP padding between functions, those NOPs aren't
associated with a function symbol, which breaks objtool's detection of a
function falling through to another function.  Instead it shows
confusing errors like:

  drivers/mtd/chips/cfi_util.o: warning: objtool: cfi_qry_mode_on()+0x8b: return with modified stack frame
  drivers/mtd/chips/cfi_util.o: warning: objtool: cfi_qry_mode_on()+0x0: stack state mismatch: cfa1=-4-32 cfa2=7+8
  drivers/mtd/chips/cfi_cmdset_0002.o: warning: objtool: fixup_use_fwh_lock()+0x8: unknown stack-related register move
  drivers/mtd/chips/cfi_cmdset_0002.o: warning: objtool: fixup_use_fwh_lock()+0x0: stack state mismatch: cfa1=6+16 cfa2=7+8
  drivers/mtd/chips/cfi_cmdset_0002.o: warning: objtool: do_otp_write()+0xa: unsupported stack pointer realignment
  drivers/mtd/chips/cfi_cmdset_0002.o: warning: objtool: do_otp_write()+0x0: stack state mismatch: cfa1=-4-40 cfa2=7+8
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/43e7aae9a7a7710cd6df597fa9dc501da4ba0602.1502472193.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

When GCC realigns a function's stack, it sometimes uses %r13 as the DRAP
register, like:

  push	%r13
  lea	0x10(%rsp), %r13
  and	$0xfffffffffffffff0, %rsp
  pushq	-0x8(%r13)
  push	%rbp
  mov	%rsp, %rbp
  push	%r13
  ...
  mov	-0x8(%rbp),%r13
  leaveq
  lea	-0x10(%r13), %rsp
  pop	%r13
  retq

Since %r13 was pushed onto the stack twice, its two stack locations need
to be stored separately.  The first push of %r13 is its original value,
and the second push of %r13 is the caller's stack frame address.

Since %r13 is a callee-saved register, we need to track the stack
location of its original value separately from the DRAP register.

This fixes the following false positive warning:

  lib/ubsan.o: warning: objtool: val_to_string.constprop.7()+0x97: leave instruction with modified stack frame
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: baa41469 ("objtool: Implement stack validation 2.0")
Link: http://lkml.kernel.org/r/3da23a6d4c5b3c1e21fc2ccc21a73941b97ff20a.1502401017.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The validate_branch() function should never return a negative value.
Errors are treated as warnings so that even if something goes wrong,
objtool does its best to generate ORC data for the rest of the file.
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: baa41469 ("objtool: Implement stack validation 2.0")
Link: http://lkml.kernel.org/r/d86671cfde823b50477cd2f6f548dfe54871e24d.1502401017.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

When a whitelisted function uses one of the ALTERNATIVE macros, it
produces false positive warnings like:

  arch/x86/kvm/vmx.o: warning: objtool: .altinstr_replacement+0x0: unreachable instruction
  arch/x86/kvm/svm.o: warning: objtool: .altinstr_replacement+0x6e: unreachable instruction

There's no easy way to whitelist alternative instructions, so instead
just skip any 'unreachable' warnings associated with them.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/a5d0a8c60155f03b36a31fac871e12cf75f35fd0.1501188854.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Arnd reported some false positive warnings with GCC 7:

  drivers/hid/wacom_wac.o: warning: objtool: wacom_bpt3_touch()+0x2a5: stack state mismatch: cfa1=7+8 cfa2=6+16
  drivers/iio/adc/vf610_adc.o: warning: objtool: vf610_adc_calculate_rates() falls through to next function vf610_adc_sample_set()
  drivers/pwm/pwm-hibvt.o: warning: objtool: hibvt_pwm_get_state() falls through to next function hibvt_pwm_remove()
  drivers/pwm/pwm-mediatek.o: warning: objtool: mtk_pwm_config() falls through to next function mtk_pwm_enable()
  drivers/spi/spi-bcm2835.o: warning: objtool: .text: unexpected end of section
  drivers/spi/spi-bcm2835aux.o: warning: objtool: .text: unexpected end of section
  drivers/watchdog/digicolor_wdt.o: warning: objtool: dc_wdt_get_timeleft() falls through to next function dc_wdt_restart()

When GCC 7 detects a potential divide-by-zero condition, it sometimes
inserts a UD2 instruction for the case where the divisor is zero,
instead of letting the hardware trap on the divide instruction.

Objtool doesn't consider UD2 to be fatal unless it's annotated with
unreachable().  So it considers the GCC-generated UD2 to be non-fatal,
and it tries to follow the control flow past the UD2 and gets
confused.

Previously, objtool *did* assume UD2 was always a dead end.  That
changed with the following commit:

  d1091c7f ("objtool: Improve detection of BUG() and other dead ends")

The motivation behind that change was that Peter was planning on using
UD2 for __WARN(), which is *not* a dead end.  However, it turns out
that some emulators rely on UD2 being fatal, so he ended up using
'ud0' instead:

  9a93848f ("x86/debug: Implement __WARN() using UD0")

For GCC 4.5+, it should be safe to go back to the previous assumption
that UD2 is fatal, even when it's not annotated with unreachable().

But for pre-4.5 versions of GCC, the unreachable() macro isn't
supported, so such cases of UD2 need to be explicitly annotated as
reachable.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: d1091c7f ("objtool: Improve detection of BUG() and other dead ends")
Link: http://lkml.kernel.org/r/e57fa9dfede25f79487da8126ee9cdf7b856db65.1501188854.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Objtool tries to silence 'unreachable instruction' warnings when it
detects gcov is enabled, because gcov produces a lot of unreachable
instructions and they don't really matter.

However, the 0-day bot is still reporting some unreachable instruction
warnings with CONFIG_GCOV_KERNEL=y on GCC 4.6.4.

As it turns out, objtool's gcov detection doesn't work with older
versions of GCC because they don't create a bunch of symbols with the
'gcov.' prefix like newer versions of GCC do.

Move the gcov check out of objtool and instead just create a new
'--no-unreachable' flag which can be passed in by the kernel Makefile
when CONFIG_GCOV_KERNEL is defined.

Also rename the 'nofp' variable to 'no_fp' for consistency with the new
'no_unreachable' variable.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 9cfffb11 ("objtool: Skip all "unreachable instruction" warnings for gcov kernels")
Link: http://lkml.kernel.org/r/c243dc78eb2ffdabb6e927844dea39b6033cd395.1500939244.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Some asm (and inline asm) code does special things to the stack which
objtool can't understand.  (Nor can GCC or GNU assembler, for that
matter.)  In such cases we need a facility for the code to provide
annotations, so the unwinder can unwind through it.

This provides such a facility, in the form of unwind hints.  They're
similar to the GNU assembler .cfi* directives, but they give more
information, and are needed in far fewer places, because objtool can
fill in the blanks by following branches and adjusting the stack pointer
for pushes and pops.
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/0f5f3c9104fca559ff4088bece1d14ae3bca52d5.1499786555.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Now that objtool knows the states of all registers on the stack for each
instruction, it's straightforward to generate debuginfo for an unwinder
to use.

Instead of generating DWARF, generate a new format called ORC, which is
more suitable for an in-kernel unwinder.  See
Documentation/x86/orc-unwinder.txt for a more detailed description of
this new debuginfo format and why it's preferable to DWARF.
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/c9b9f01ba6c5ed2bdc9bb0957b78167fdbf9632e.1499786555.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

With some configs, objtool reports the following warning:

  arch/x86/kernel/ftrace.o: warning: objtool: ftrace_modify_code_direct()+0x2d: sibling call from callable instruction with modified stack frame

The instruction it's complaining about isn't actually a sibling call.
It's just a normal jump to an address inside the function.  Objtool
thought it was a sibling call because the instruction's jump_dest wasn't
initialized because the function was supposed to be ignored due to its
use of sync_core().

Objtool ended up validating the function instead of ignoring it because
it didn't properly recognize a sibling call to the function.  So fix the
sibling call logic.  Also add a warning to catch ignored functions being
validated so we'll get a more useful error message next time.
Reported-by: NMike Galbraith <efault@gmx.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/96cc8ecbcdd8cb29ddd783817b4af918a6a171b0.1499437107.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Previously, objtool ignored functions which have the IRET instruction
in them.  That's because it assumed that such functions know what
they're doing with respect to frame pointers.

With the new "objtool 2.0" changes, it stopped ignoring such functions,
and started complaining about them:

  arch/x86/kernel/alternative.o: warning: objtool: do_sync_core()+0x1b: unsupported instruction in callable function
  arch/x86/kernel/alternative.o: warning: objtool: text_poke()+0x1a8: unsupported instruction in callable function
  arch/x86/kernel/ftrace.o: warning: objtool: do_sync_core()+0x16: unsupported instruction in callable function
  arch/x86/kernel/cpu/mcheck/mce.o: warning: objtool: machine_check_poll()+0x166: unsupported instruction in callable function
  arch/x86/kernel/cpu/mcheck/mce.o: warning: objtool: do_machine_check()+0x147: unsupported instruction in callable function

Silence those warnings for now.  They can be re-enabled later, once we
have unwind hints which will allow the code to annotate the IRET usages.
Reported-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Fixes: baa41469 ("objtool: Implement stack validation 2.0")
Link: http://lkml.kernel.org/r/20170630140934.mmwtpockvpupahro@trebleSigned-off-by: NIngo Molnar <mingo@kernel.org>

This is a major rewrite of objtool.  Instead of only tracking frame
pointer changes, it now tracks all stack-related operations, including
all register saves/restores.

In addition to making stack validation more robust, this also paves the
way for undwarf generation.
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/678bd94c0566c6129bcc376cddb259c4c5633004.1498659915.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

In preparation for the new 'objtool undwarf generate' command, which
will rely on 'objtool check', move the checking code from
builtin-check.c to check.c where it can be used by other commands.
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: NJiri Slaby <jslaby@suse.cz>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/294c5c695fd73c1a5000bbe5960a7c9bec4ee6b4.1498659915.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

CONFIG_FORTIFY_SOURCE=y implements fortify_panic() as a __noreturn function,
so objtool needs to know about it too.
Suggested-by: NDaniel Micay <danielmicay@gmail.com>
Tested-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1497532835-32704-1-git-send-email-jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

And with the goodies present in the kernel.h counterpart, i.e. checking
that the parameter is an array at build time.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-roiwxwgwgld4kygn65if60wa@git.kernel.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

Arnd Bergmann reported a (false positive) objtool warning:

  drivers/infiniband/sw/rxe/rxe_resp.o: warning: objtool: rxe_responder()+0xfe: sibling call from callable instruction with changed frame pointer

The issue is in find_switch_table().  It tries to find a switch
statement's jump table by walking backwards from an indirect jump
instruction, looking for a relocation to the .rodata section.  In this
case it stopped walking prematurely: the first .rodata relocation it
encountered was for a variable (resp_state_name) instead of a jump
table, so it just assumed there wasn't a jump table.

The fix is to ignore any .rodata relocation which refers to an ELF
object symbol.  This works because the jump tables are anonymous and
have no symbols associated with them.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 3732710f ("objtool: Improve rare switch jump table pattern detection")
Link: http://lkml.kernel.org/r/20170302225723.3ndbsnl4hkqbne7a@trebleSigned-off-by: NIngo Molnar <mingo@kernel.org>

The '__unreachable' and '__func_stack_frame_non_standard' sections are
only used at compile time.  They're discarded for vmlinux but they
should also be discarded for modules.

Since this is a recurring pattern, prefix the section names with
".discard.".  It's a nice convention and vmlinux.lds.h already discards
such sections.

Also remove the 'a' (allocatable) flag from the __unreachable section
since it doesn't make sense for a discarded section.
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Jessica Yu <jeyu@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: d1091c7f ("objtool: Improve detection of BUG() and other dead ends")
Link: http://lkml.kernel.org/r/20170301180444.lhd53c5tibc4ns77@trebleSigned-off-by: NIngo Molnar <mingo@kernel.org>

The BUG() macro's use of __builtin_unreachable() via the unreachable()
macro tells gcc that the instruction is a dead end, and that it's safe
to assume the current code path will not execute past the previous
instruction.

On x86, the BUG() macro is implemented with the 'ud2' instruction.  When
objtool's branch analysis sees that instruction, it knows the current
code path has come to a dead end.

Peter Zijlstra has been working on a patch to change the WARN macros to
use 'ud2'.  That patch will break objtool's assumption that 'ud2' is
always a dead end.

Generally it's best for objtool to avoid making those kinds of
assumptions anyway.  The more ignorant it is of kernel code internals,
the better.

So create a more generic way for objtool to detect dead ends by adding
an annotation to the unreachable() macro.  The annotation stores a
pointer to the end of the unreachable code path in an '__unreachable'
section.  Objtool can read that section to find the dead ends.
Tested-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/41a6d33971462ebd944a1c60ad4bf5be86c17b77.1487712920.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The following commit:

  3732710f ("objtool: Improve rare switch jump table pattern detection")

... improved objtool's ability to detect GCC switch statement jump
tables for GCC 6.  However the check to allow short jumps with the
scanned range of instructions wasn't quite right.  The pattern detection
should allow jumps to the indirect jump instruction itself.

This fixes the following warning:

  drivers/infiniband/sw/rxe/rxe_comp.o: warning: objtool: rxe_completer()+0x315: sibling call from callable instruction with changed frame pointer
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 3732710f ("objtool: Improve rare switch jump table pattern detection")
Link: http://lkml.kernel.org/r/20161026153408.2rifnw7bvoc5sex7@trebleSigned-off-by: NIngo Molnar <mingo@kernel.org>

Recently objtool has started reporting a few "unreachable instruction"
warnings when CONFIG_GCOV is enabled for newer versions of GCC.  Usually
this warning means there's some new control flow that objtool doesn't
understand.  But in this case, objtool is correct and the instructions
really are inaccessible.  It's an annoying quirk of gcov, but it's
harmless, so it's ok to just silence the warnings.

With older versions of GCC, it was relatively easy to detect
gcov-specific instructions and to skip any unreachable warnings produced
by them.  But GCC 6 has gotten craftier.

Instead of continuing to play whack-a-mole with gcov, just use a bigger,
more permanent hammer and disable unreachable warnings for the whole
file when gcov is enabled.  This is fine to do because a) unreachable
warnings are usually of questionable value; and b) gcov isn't used for
production kernels and we can relax the checks a bit there.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/38d5c87d61d9cd46486dd2c86f46603dff0df86f.1476393584.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

GCC 6 added a new switch statement jump table optimization which makes
objtool's life harder.  It looks like:

  mov [rodata addr],%reg1
  ... some instructions ...
  jmpq *(%reg1,%reg2,8)

The optimization is quite rare, but objtool still needs to be able to
identify the pattern so that it can follow all possible control flow
paths related to the switch statement.

In order to detect the pattern, objtool starts from the indirect jump
and scans backwards through the function until it finds the first
instruction in the pattern.  If it encounters an unconditional jump
along the way, it stops and considers the pattern to be not found.

As it turns out, unconditional jumps can happen, as long as they are
small forward jumps within the range being scanned.

This fixes the following warnings:

  drivers/infiniband/sw/rxe/rxe_comp.o: warning: objtool: rxe_completer()+0x2f4: sibling call from callable instruction with changed frame pointer
  drivers/infiniband/sw/rxe/rxe_resp.o: warning: objtool: rxe_responder()+0x10f: sibling call from callable instruction with changed frame pointer
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/8a9ed68ae1780e8d3963e4ee13f2f257fe3a3c33.1476393584.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

objtool reports the following new warning:

  kernel/exit.o: warning: objtool: do_exit() falls through to next function complete_and_exit()

The warning is caused by do_exit()'s new call to do_task_dead(), which
is a new "noreturn" function which objtool doesn't know about yet,
introduced by:

  9af6528e ("sched/core: Optimize __schedule()")

( objtool has to know all the global noreturn functions so it can follow
  the control flow of any functions which call them.  Unfortunately they
  need to be hard-coded because there's no automated way to detect them. )
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kbuild-all@01.org
Cc: tipbuild@zytor.com
Link: http://lkml.kernel.org/r/20160922212125.zbuewckqll4yur25@trebleSigned-off-by: NIngo Molnar <mingo@kernel.org>

This fixes some false positive objtool warnings seen with gcc 6.1.1:

  kernel/trace/ring_buffer.o: warning: objtool: ring_buffer_read_page()+0x36c: sibling call from callable instruction with changed frame pointer
  arch/x86/kernel/reboot.o: warning: objtool: native_machine_emergency_restart()+0x139: sibling call from callable instruction with changed frame pointer
  lib/xz/xz_dec_stream.o: warning: objtool: xz_dec_run()+0xc2: sibling call from callable instruction with changed frame pointer

With GCC 6, a new code pattern is sometimes used to access a switch
statement jump table in .rodata, which objtool doesn't yet recognize:

  mov [rodata addr],%reg1
  ... some instructions ...
  jmpq *(%reg1,%reg2,8)

Add support for detecting that pattern.  The detection code is rather
crude, but it's still effective at weeding out false positives and
catching real warnings.  It can be refined later once objtool starts
reading DWARF CFI.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/b8c9503b4ad8c8a827cc5400db4c1b40a3ea07bc.1469751119.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

gcc version 4.1.2 20080704 (Red Hat 4.1.2-55) barfs with:

    CC       /tmp/build/objtool/builtin-check.o
  cc1: warnings being treated as errors
  builtin-check.c: In function 'cmd_check':
  builtin-check.c:667: warning: 'prev_rela' may be used uninitialized in this function
  mv: cannot stat `/tmp/build/objtool/.builtin-check.o.tmp': No such file or directory
  make[1]: *** [/tmp/build/objtool/builtin-check.o] Error 1

Init it to NULL to silence it.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-qolo31rl2ojlwj1lj9dhemyz@git.kernel.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

They were in tools/include/linux/kernel.h, requiring that it in turn
included stdio.h, which is way too heavy.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-855h8olnkot9v0dajuee1lo3@git.kernel.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>