This patch enables the load balancing capability of firmware
and hardware to spray traffic into different cpus through
separate rx msix interrupts.

The feature is being enabled for NX3031, NX2031 (old) will be
enabled later. This depends on msi-x and compatibility with
msi and legacy is maintained by enabling single rx ring.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o remove max_ prefix from ring sizes, since they don't really
  represent max possible sizes.
o cleanup naming of rx ring types (normal, jumbo, lro).
o simplify logic to choose rx ring size, gig ports get half
  rx ring of 10 gig ports.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Detach network interface on PCI suspend and recreate hardware
context after resumes.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation for the ixgbe driver in the kernel docs area is missing.
This adds that documentation.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Tx DMA unit should be disabled when bringing the device down.  Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel.  In those cases, we'd rather
fail gracefully instead of a panic.  Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cleans up the following pieces of the Rx initialization path:

- Enable the ECC memory fault interrupt in OTHER causes.

- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled.  We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.

- Fix the RSS initialization path to not stomp on DCB accidentally.  When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status.  The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.

Solution: call napi_add before calling request_irq
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt models using EITR have changed in 82599.  The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't.  This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82599 mistakenly enabled drop on Rx queues in the packet buffer.  The
default mode should be store-and-forward from the FIFO.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly.  In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A purely cosmetic change.  Report which physical layer is present, instead
of PHY unknown.  82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 82576 copper adapter and necessary code to restrict wol for
quad port adapter to first port.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding device id to support 82576NS dual port copper
NIC.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects a typo that was doing a less than comparison instead of
a left shift due to the fact that I didn't get enough <'s in there.

This resolves an issue in which vlans were not functioning correctly.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Pf to pool if adding a VLVF register value and the VFTA bit is
already set.

This patch addresses the unlikely situation that the PF adds a vlan
entry when the vlvf is full, and a vf later adds the vlan to the vlvf.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to support wol on the second port for situations such as when the
lan ports are on the motherboard itself.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If DCA is undefined then the adapter struct becomes unnecessary.  To
resolve this issue the DCA calls can simply make a call to the adapter
struct through the rx_ring adapter struct member.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netif_running check in igb poll is a hold over from the use of fake
netdevs to use multiple queues with NAPI prior to 2.6.24.  It is no longer
necessary to have the call there and it currently can cause errors if
work_done == budget.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the new DCA API, the driver should use dca3_get_tag() instead of
the obsolete dca_get_tag().

Signed-off-by: Maciej Sosnowski < maciej.sosnowski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I found the PPP subsystem to not work properly when connecting channels
with different speeds to the same bundle.

Problem Description:

As the "ppp_mp_explode" function fragments the sk_buff buffer evenly
among the PPP channels that are connected to a certain PPP unit to
make up a bundle, if we are transmitting using an upper layer protocol
that requires an Ack before sending the next packet (like TCP/IP for
example), we will have a bandwidth bottleneck on the slowest channel
of the bundle.

Let's clarify by an example. Let's consider a scenario where we have
two PPP links making up a bundle: a slow link (10KB/sec) and a fast
link (1000KB/sec) working at the best (full bandwidth). On the top we
have a TCP/IP stack sending a 1000 Bytes sk_buff buffer down to the
PPP subsystem. The "ppp_mp_explode" function will divide the buffer in
two fragments of 500B each (we are neglecting all the headers, crc,
flags etc?.). Before the TCP/IP stack sends out the next buffer, it
will have to wait for the ACK response from the remote peer, so it
will have to wait for both fragments to have been sent over the two
PPP links, received by the remote peer and reconstructed. The
resulting behaviour is that, rather than having a bundle working
@1010KB/sec (the sum of the channels bandwidths), we'll have a bundle
working @20KB/sec (the double of the slowest channels bandwidth).


Problem Solution:

The problem has been solved by redesigning the "ppp_mp_explode"
function in such a way to make it split the sk_buff buffer according
to the speeds of the underlying PPP channels (the speeds of the serial
interfaces respectively attached to the PPP channels). Referring to
the above example, the redesigned "ppp_mp_explode" function will now
divide the 1000 Bytes buffer into two fragments whose sizes are set
according to the speeds of the channels where they are going to be
sent on (e.g .  10 Byets on 10KB/sec channel and 990 Bytes on
1000KB/sec channel).  The reworked function grants the same
performances of the original one in optimal working conditions (i.e. a
bundle made up of PPP links all working at the same speed), while
greatly improving performances on the bundles made up of channels
working at different speeds.
Signed-off-by: NGabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

promote 'cnt' to size_t, to match 'len'.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->len is an unsigned int, so the test in x25_rx_call_request() always
evaluates to true.

len in x25_sendmsg() is unsigned as well. so -ERRORS returned by x25_output()
are not noticed.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Windows (XP at least) hosts on boot, with configured static ip, performing 
address conflict detection, which is defined in RFC3927.
Here is quote of important information:

"
An ARP announcement is identical to the ARP Probe described above, 
except    that now the sender and target IP addresses are both set 
to the host's newly selected IPv4 address. 
"

But it same time this goes wrong with RFC5227.
"
The 'sender IP address' field MUST be set to all zeroes; this is to avoid
polluting ARP caches in other hosts on the same link in the case
where the address turns out to be already in use by another host.
"

When ARP proxy configured, it must not answer to both cases, because 
it is address conflict verification in any case. For Windows it is just 
causing to detect false "ip conflict". Already there is code for RFC5227, so 
just trivially we just check also if source ip == target ip.
Signed-off-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original patch was submitted last year but wasn't discussed or applied
because of missing maintainer's CCs. I only fixed some formatting errors,
but as I saw tulip is very badly formatted and needs further work.

Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We
should allow receiving frames of up to 1518 bytes in length, instead of
1514.

Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived
at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.

Tested on D-Link DFE-570TX quad-fastethernet card.
Signed-off-by: NTomasz Lemiech <szpajder@staszic.waw.pl>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NBen McKeegan <ben@netservers.co.uk>
Acked-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.

Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Pavel Roskin <proski@gnu.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the circular locking problem by changing the locking strategy
concerning the logging of firmware handles.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing the mac address when a macvlan device is up will leave the
device on the wrong hash chain making it impossible to receive
packets.

There is no checking of the mac address set on the macvlan.  Allowing
a misconfiguration to grab packets from the the underlying device or
another macvlan.

To resolve these problems I update the hash table of macvlans when the
mac address of a macvlan changes, and when updating the hash table
I verify that the new mac address is usable.

The result is well defined and predictable if not perfect handling of
mac vlan mac addresses.

To keep the code clear I have created a set of hash table maintenance
in macvlan so I am not open coding the hash function and the logic
needed to update the hash table all over the place.
Signed-off-by: NEric Biederman <ebiederm@aristanetworks.com>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running in a network namespace whose only link to
the outside world is a macvlan device, not being
able to create another macvlan is a real pain.

So modify macvlan creation to allow automatically forward
a creation of a macvlan on a macvlan to become a creation
of a macvlan on the underlying network device.
Signed-off-by: NEric Biederman <ebiederm@aristanetworks.com>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch from Juha Leppanen suppresses a false warning if the eeprom
load succeeds on the very last attempt.

Juha> In function smsc911x_open smsc911x_reg_read+udelay can be run 50
Juha> times with timeout reaching -1, and the following if statetement
Juha> does not catch the timeout and no warning is issued. Also if the
Juha> 50th smsc911x_reg_read is GOOD, loop is exited with timeout as 0
Juha> and bogus warning issued.  Replace testing order and --timeout
Juha> instead of timeout-- and now max 50 smsc911x_reg_read's are done,
Juha> with max 49 udelays.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch from Juha Leppanen suppresses a false warning if a fast
forward operation succeeds on the very last attempt.

Juha> If smsc911x_reg_read loop is executed 500 times, timeout reaches 0
Juha> and the 500th smsc911x_reg_read result in val is ignored. If
Juha> testing order is changed, then val is checked first. The 500th
Juha> reg_read might be GOOD, why ignore it!
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network Drop Monitor: Adding Build changes to enable drop monitor
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

 include/linux/Kbuild |    1 +
 net/Kconfig          |   11 +++++++++++
 net/core/Makefile    |    1 +
 3 files changed, 13 insertions(+)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

 include/linux/net_dropmon.h |   56 +++++++++
 net/core/drop_monitor.c     |  263 ++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 319 insertions(+)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network Drop Monitor: Adding kfree_skb_clean for non-drops and modifying end-of-line points for skbs
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

 include/linux/skbuff.h |    4 +++-
 net/core/datagram.c    |    2 +-
 net/core/skbuff.c      |   22 ++++++++++++++++++++++
 net/ipv4/arp.c         |    2 +-
 net/ipv4/udp.c         |    2 +-
 net/packet/af_packet.c |    2 +-
 6 files changed, 29 insertions(+), 5 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

 include/trace/skb.h   |    8 ++++++++
 net/core/Makefile     |    2 ++
 net/core/net-traces.c |   29 +++++++++++++++++++++++++++++
 3 files changed, 39 insertions(+)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>