- 17 6月, 2009 3 次提交
-
-
由 Miroslav Sustek 提交于
Enables analog/digital tv, radio and remote control (gpio). Tested-by: NMarcin Wojcikowski <emtees.mts@gmail.com> Tested-by: NKarel Juhanak <karel.juhanak@warnet.cz> Tested-by: NAndrew Goff <goffa72@gmail.com> Tested-by: NJan Novak <novak-j@seznam.cz> Signed-off-by: NMiroslav Sustek <sustmidown@centrum.cz> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
According to the engineer at PCTV Systems, the xc5000 reset pin is supposed to be on GPIO12. However, despite three nights of effort, pulling that GPIO low didn't reset the xc5000. While pulling MO_SRST_IO low does reset the xc5000, this also resets in the s5h1409 being reset as well. This causes tuning to always fail since the internal state of the s5h1409 does not match the driver's state. Given that the only two conditions in which the driver performs a reset is during firmware load and powering down the chip, I am taking out the reset. We know that the chip is being reset when the cx88 comes online, and not being able to do power management for this board is better than not having any tuning at all. Problem discovered when implementing proper power management for the xc5000, which results in calls to the reset callback *after* s5h1409 is initialized. Cc: Steven Toth <stoth@kernellabs.com> Cc: Chaogui Zhang <czhang1974@gmail.com> Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Steven Toth 提交于
cx88: Add support for the Hauppauge IROnly board. Signed-off-by: NSteven Toth <stoth@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 07 4月, 2009 2 次提交
-
-
由 Hans Verkuil 提交于
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on i2c_get_adapdata to return the v4l2_device. However, this is not always possible on embedded platforms. So modify the API to pass the v4l2_device pointer explicitly. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
s_standby is only used to put the tuner in powersaving mode, so move it from core to tuner. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 30 3月, 2009 5 次提交
-
-
由 Hans Verkuil 提交于
tuner-core.c contains a hack for cx88 board to prevent probing of certain addresses: /* HACK: Ignore 0x6b and 0x6f on cx88 boards. * FusionHDTV5 RT Gold has an ir receiver at 0x6b * and an RTC at 0x6f which can get corrupted if probed. */ With the new i2c API this hack no longer works. So instead change the list of tuner probe addresses in the cx88 driver itself, which is much more clean. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Convert cx88 to use v4l2_subdev since the old i2c autoprobing mechanism will be removed. Added code to explicitly load tvaudio where needed. Also fix the rtc-isl1208 support: since that driver no longer supports autoprobing it has to be loaded using the new i2c API. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Alan Cox 提交于
The ioremap one was reported in October 2007 (Bug 9146), the kmalloc one was blindingly obvious while looking at the ioremap one The bug suggests some other configuration for lots of I/O memory (32MB per device is ioremapped) but I'll leave that to the real maintainers Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Stephan Wienczny 提交于
This patch adds support for Terratec Cinergy HT PCI MKII with card id 79. Its more or less a copy of Pinnacle Hybrid PCTV. Thanks to k1ngf1sher on forum.ubuntuusers.de for the idea to copy that card. Signed-off-by: NStephan Wienczny <stephan@wienczny.de> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 30 12月, 2008 4 次提交
-
-
由 Vincent Pelletier 提交于
Add support for the following inputs: - radio tuner - composite 1 & 2 (only 1 is physically available, but composite 2 is also advertised by windows driver) - svideo Signed-off-by: NVincent Pelletier <plr.vincent@gmail.com> Acked-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Igor M. Liplianin 提交于
The card based on stv0299 or stv0288 demodulators. Signed-off-by: NIgor M. Liplianin <liplianin@me.by> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Igor M. Liplianin 提交于
The card based on stv0299 or stv0288 demodulators. Signed-off-by: NIgor M. Liplianin <liplianin@me.by> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Patrice Levesque 提交于
There's a second PCI identifier for the ATI TV WONDER PRO card (0x1002:0x00f9). Attached is a patch to kernel 2.6.27 that adds autodetection for this version. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 22 10月, 2008 1 次提交
-
-
由 Mauro Carvalho Chehab 提交于
The multifrontend changes on cx88 assumed that all boards that use cx88-mpeg supports DVB. This is not true. There also a few analog-only boards based on Blackboard design that also uses cx88-mpeg. For those boards, there's no need to allocate dvb frontends. This patch fixes videobuf allocation for those devices. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 18 10月, 2008 6 次提交
-
-
由 Darron Broad 提交于
This adds audio routing for the hvr-1300/3000/4000 cards enabling FM audio for the I2S ADC method of the cx88. At this time only the HVR-4000 has been tested. It is assumed the HVR-3000/1300 are the same. Signed-off-by: NDarron Broad <darron@kewl.org> Signed-off-by: NSteven Toth <stoth@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Darron Broad 提交于
This add initial configuration for radio support on the hvr-3000/4000. FM radio doesn't work as yet without further patches (to come), but this prepares for that. Experimental radio support shows that it works when combined with additional audio routing work for cards with an FMD1216ME analogue frontend, but not the MEX variant (more later). Signed-off-by: NDarron Broad <darron@kewl.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Darron Broad 提交于
This adds audio routing on the hvr-3000/4000 This is a preliminary patch for later routing requirements. This adds line-in support on the 2 cards mentioned. It is also apparent that there is an initial open fault for line-in when opening composite/s-video. This will be fixed later. It was also noticed that the bit-field for audio routing which was 2 bits needs an increase as the WM8775 for example, allows a value 4 bits wide for it's audio mux. Signed-off-by: NDarron Broad <darron@kewl.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Darron Broad 提交于
The cx22702 is now always reset on module load. Prior to this the cx22702 was not found on i2c scan without a full reset. Signed-off-by: NDarron Broad <darron@kewl.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Darron Broad 提交于
A number of reference to videobuf_dvb_get_frontend used an invalid index. This has been fixed. The section for the HVR3000 in advise_acquire was redundant as the same logic is used on the HVR4000. This has been removed and both cards now use the same function. A number of small errors and whitespace errors are also fixed. Signed-off-by: NDarron Broad <darron@kewl.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Steven Toth 提交于
A detailed description from the original patches 2 years ago: "The WinTV-HVR3000 has a single transport bus which is shared between a DVB-T and DVB-S modulator. These patches build on the bus acquisition cx88 work from a few weeks ago to add support for this. So to applications the HVR3000 looks like this: /dev/dvb/adapter0/fe0 (cx24123 DVB-S demod) /dev/dvb/adapter0/fe1 (cx22702 DVB-T demod) Additional boards continue as before, eg: /dev/dvb/adapter1/fe0 (lgdt3302 ATSC demod) The basic change is removing the single instance of the videobuf_dvb in cx8802_dev and saa7134_dev(?) and replacing it with a list and some supporting functions. *NOTE* This branch was taken before v4l-dvb was closed for 2.6.19 so two or three current cx88 patches appear to be reversed by this tree, this will be cleaned up in the near future. The patches missing change the mutex handing to core->lock, fix an enumeration problem." It should be recognised that a number of people have been maintaining this patchset. Significant levels of Kudos to everyone one involved, including but not limited to: Darron Broad Fabio M. Di Nitto Carlo Scarfoglio Hans Werner Without the work of these people, and countless others, my two year old patches would of died on the Mercurial linuxtv.org vine a long time ago. TODO: Revise these patches a little further so that the need for demux1 and dvr0 is optional, not mandatory on the HVR3000. HISTORY (darron): This is the last update to MFE prepared by Hans which is based upon the `scratchpad' diff created by Carlo. All MFE work prior to that point must be attributed to Fabio who ported and maintained Steve's original patch up to that time. Signed-off-by: NSteven Toth <stoth@linuxtv.org> Signed-off-by: NDarron Broad <darron@kewl.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 13 10月, 2008 1 次提交
-
-
由 Oleg Roitburd 提交于
Added support for Prof 7300 DVB-S/S2 card. The card based on cx24116 demodulator. Signed-off-by: NOleg Roitburd <oroitburd@gmail.com> Signed-off-by: NSteven Toth <stoth@linuxtv.org> [mchehab@redhat.com: fixed CARDLIST.cx88 entry] Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 12 10月, 2008 10 次提交
-
-
由 Tim Farrington 提交于
Well, one thing you encouraged me to do was re-test some of my cards which contained the xc3028-zarlink combo. Which led me to test a Dvico FusionHDTV Pro. Almost a year ago, Chris Pascoe did a patch for this which can be found at his ~pascoe/xc-test at Linuxtv. This worked very well, however that was using his version of firmware. Alas, someone attempted to use this and patch v4l-dvb, and messed it up. So I've fixed it. I enclose the patch against today's tree (containing your latest tuner-xc2028.c patch). The card now works very well, well with DVB-T anyway. Signed-off-by: NTim Farrington <timf@iinet.net.au> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Stéphane Voltz 提交于
This patch against latest mercurial makes DVB-T working on Pinnacle Hybrid PCTV Pro (pctv310c). In cx88-dvb.c, a specific zl10353_config is created with the if2 inferred from the old comment in the currently used config. It is then used for attach, and i2c_gate_ctrl is set to NULL. The entry in cx88-cards.c is modified with GPIO gathered from windows with regspy, and DVB enabled. The frontend is set to XC3028_FE_ZARLINK456 to match the zl10353_config. It is working great with the freeview channels I can receive. Signed-off-by: NStéphane Voltz <stef.dev@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Thanks to Sidney Matias <sidney.matias@gmail.com> for getting GPIO values and testing on this device. Cc: Sidney Matias <sidney.matias@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Igor M. Liplianin 提交于
Add support for ST STV0288 demodulator and cards with it, such as TeVii S420. Patch is co-authored with Georg Acher <acher@baycom.de> Signed-off-by: NGeorg Acher <acher@baycom.de> Signed-off-by: NIgor M. Liplianin <liplianin@me.by> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Steven Toth 提交于
Patch by Darron Broad. Signed-off-by: NSteven Toth <stoth@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Oleg Roitburd 提交于
Added support for TBS 8920 DVB-S/S2 card. The card based on cx24116 demodulator. Signed-off-by: NOleg Roitburd <oroitburd@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Oleg Roitburd 提交于
Added support for Omicom SS4 DVB-S/S2 card. The card based on cx24116 demodulator. Signed-off-by: NOleg Roitburd <oroitburd@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Igor M. Liplianin 提交于
Added support for TeVii S460 DVB-S/S2 card. The card based on cx24116 demodulator. Signed-off-by: NIgor M. Liplianin <liplianin@me.by> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Steven Toth 提交于
Adding support for Hauppauge's cx88 S2 based products, based on the cx24116 DVB-S2 demodulator. Signed-off-by: NSteven Toth <stoth@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 26 7月, 2008 1 次提交
-
-
由 Hans Verkuil 提交于
Converted the last users of audiochip.h to the v4l2-chip-ident.h header and remove the now unused audiochip.h header. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 05 6月, 2008 1 次提交
-
-
由 Daniel Gimpelevich 提交于
Signed-off-by: NDaniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 30 4月, 2008 1 次提交
-
-
由 Mauro Carvalho Chehab 提交于
Tuner setup were happening during i2c attach callback. This means that it would happen on two conditions: 1) if tuner module weren't load, it will happen at request_module("tuner"); 2) if tuner is not compiled as a module, or it is already loaded (for example, on setups with more than one tuner), it will happen when cx88 registers I2C bus. Due to that, if tuner were loaded, tuner setup will happen _before_ reading the proper values at tuner eeprom. Since set_addr refuses to change for a tuner that were previously defined (except if the tuner_addr is set), this were making eeprom tuner detection useless. This patch removes tuner type setup from cx88-i2c, moving it to the proper place, after taking eeprom into account. Reviewed-by: NGert Vervoort <gert.vervoort@hccnet.nl> Reviewed-by: NIan Pickworth <ian@pickworth.me.uk> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 26 4月, 2008 1 次提交
-
-
由 Steven Toth 提交于
The S5H1411 demodulator is now enabled. Signed-off-by: NSteven Toth <stoth@hauppauge.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 25 4月, 2008 4 次提交
-
-
由 Steven Toth 提交于
cx88: enable radio GPIO correctly. Signed-off-by: NSteven Toth <stoth@hauppauge.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Dâniel Fraga 提交于
The attached patch fixes gpio references for Powercolor Real Angel 330. Signed-off-by: NDaniel Fraga <fragabr@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Mauro Carvalho Chehab 提交于
This board has a s5h1409 demod, plus a xc30x8 tuner (probably, xc3018). This patch adds proper support for radio, video, s-video, composite and ATSC. However, support for radio and video depends on having s5h1409 i2c gate open, otherwise, xc30x8 chip won't be visible. For a better support, some rework is needed on cx88 driver, to allow adding xc30x8 to i2c bus without sending i2c 0 byte reading to 0xc2 address. Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com> for helping to figure out the proper parameters for s5h1409 and the GPIO pins used by each configuration. Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Mauro Carvalho Chehab 提交于
Adds a consistency check to avoid OOPS, if tuner_callback priv argument is NULL. Also, simplifies callback codes on cx88. Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-