This reverts commit c42deffd.

commit <mmc: rtsx: add support for pre_req and post_req> did use
mutex_unlock() in tasklet, but mutex_unlock() can't be used in
tasklet(atomic context). The driver needs to use mutex to avoid
concurrency, so we can't use tasklet here, the patch need to be
removed.

The spinlock host->lock and pcr->lock may deadlock, one way to solve
the deadlock is remove host->lock in sd_isr_done_transfer(), but if
using workqueue the we can avoid using the spinlock and also avoid
the problem.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

On 64 bit systems the agp_info struct has a 4 byte hole between
->agp_mode and ->aper_base.  We need to clear it to avoid disclosing
stack information to userspace.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PCF8523 uses 1-12 to represent month according to datasheet.
link: www.nxp.com/documents/data_sheet/PCF8523.pdf.
Signed-off-by: NChris Cui <chris.wei.cui@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

VCE 2.0 just like the other CIK parts.
Signed-off-by: NLeo Liu <leo.liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

Uses the same code as Kabini.
Signed-off-by: NSamuel Li <samuel.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

- Use vddc/sclk dep table for voltage if available
- Fix UVD DPM setup
- Patch voltage tables properly for non-UVD blocks
- Fix DPM + UVD/VCE on Mullins
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

Generic dpm support similar to Kabini. Mullins specific features
will be worked on later.
Signed-off-by: NSamuel Li <samuel.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

Has same version of UVD as other CIK parts.
Signed-off-by: NSamuel Li <samuel.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

Also add golden registers, update firmware loading functions.
Signed-off-by: NSamuel Li <samuel.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

Mullins is a new CI-based APU.
Signed-off-by: NSamuel Li <samuel.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=75241Signed-off-by: NChristian König <christian.koenig@amd.com>

Partially fixes: https://bugzilla.kernel.org/show_bug.cgi?id=75211Signed-off-by: NChristian König <christian.koenig@amd.com>

It would appear this bug has been copy/pasted many times without being noticed.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

The way the tile mode array index was calculated only makes sense for
the CIK specific macrotile mode array. For SI, we need to use one of the
tile mode array indices reserved for displayable surfaces.

This happened to result in correct display most if not all of the time
because most of the SI tiling modes use the same number of banks.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>

The sensor hub in Lenovo Yogas needs the enumeration quirk.  I've been running
the patch for over a month with no problems, whereas the unpatched drivers
reliably mis-initialized the sensors.
Signed-off-by: NPeter F. Patel-Schneider <pfpschneider@gmail.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Under "heavy" RX load, the driver cannot handle the descriptors fast
enough. In detail, when a descriptor is consumed, its used flag is
cleared and once the RX budget is consumed all descriptors with a
cleared used flag are prepared to receive more data. Under load though,
the HW may constantly receive more data and use those descriptors with a
cleared used flag before they are actually prepared for next usage.

The head and tail pointers into the RX-ring should always be valid and
we can omit clearing and checking of the used flag.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Coverage data suggests that the unlikely case of receiving data while
the receive handler is running may not be that unlikely.
Coverage data after running iperf for a while:
    91320:  891:	work_done = bp->macbgem_ops.mog_rx(bp, budget);
    91320:  892:	if (work_done < budget) {
     2362:  893:		napi_complete(napi);
        -:  894:
        -:  895:		/* Packets received while interrupts were disabled */
     4724:  896:		status = macb_readl(bp, RSR);
     2362:  897:		if (unlikely(status)) {
      762:  898:			if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
      762:  899:				macb_writel(bp, ISR, MACB_BIT(RCOMP));
        -:  900:			napi_reschedule(napi);
        -:  901:		} else {
     1600:  902:			macb_writel(bp, IER, MACB_RX_INT_FLAGS);
        -:  903:		}
        -:  904:	}
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When data is received during the driver processing received data the
NAPI is re-scheduled. In that case the RX interrupt should not be
re-enabled.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A few interrupt flags were not cleared in the ISR, resulting in a sytem
trapped in the ISR in cases one of those interrupts occurred. Clear all
flags to avoid such situations.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just as commit "net: macb: DMA-unmap full rx-buffer"
(48330e08), pass the size that
was used for mapping the memory also to the unmap routine to
avoid warnings from the DMA_API.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts.  The issue that necessitated the workaround has been fixed on the
newer hardware.

We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.

To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle.  This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.

Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In commit 772d05c5 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.

This same behavior is seen on i217 and i218 parts as well.  This patch expands
the original workaround to encompass these parts.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.

Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.

Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.

Fixes: b912b2f8 ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth')
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running in SRIOV mode, VM that is assigned with a non-provisioned
Ethernet VFs get themselves a random mac when the Eth driver starts. In
this case, if the IB driver startup code that deals with RoCE runs first,
it will use a zero mac as the source mac for the Para-Virtual CM MADs
which is buggy. To handle that, we change the order of loading.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code that deals with computing the slave id based on a given GID
gave wrong results when the number of single port VFs wasn't the
same for port 1 vs. port 2 and the relevant VF is single ported on
port 2. As a result, incoming CM MADs were dispatched to the wrong VF.
Fixed that and added documentation to clarify the computation steps.

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using single ported VFs and the VF is using port 2, we need
to adjust the port accordingly (change it from 1 to 2).

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hw_version 3 Elantech touchpad on the Gigabyte U2442 does not accept
0x0b as initialization value for r10, this stand-alone version of the
driver: http://planet76.com/drivers/elantech/psmouse-elantech-v6.tar.bz2

Uses 0x03 which does work, so this means not setting bit 3 of r10 which
sets: "Enable Real H/W Resolution In Absolute mode"

Which will result in half the x and y resolution we get with that bit set,
so simply not setting it everywhere is not a solution. We've been unable to
find a way to identify touchpads where setting the bit will fail, so this
patch uses a dmi based blacklist for this.

https://bugzilla.kernel.org/show_bug.cgi?id=61151

Cc: stable@vger.kernel.org
Reported-by: NPhilipp Wolfer <ph.wolfer@gmail.com>
Tested-by: NPhilipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 4d619f62 ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set.  This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.

Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.

Fixes: 4d619f62 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `altera_tse_probe':
altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask'
altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported'
altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported'
drivers/built-in.o: In function `sgdma_async_read':
altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f678): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f696): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f6f0): undefined reference to `dma_map_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f702): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sgdma_tx_buffer':
(.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_rx_status':
(.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not leak kernel-only floppy_raw_cmd structure members to userspace.
This includes the linked-list pointer and the pointer to the allocated
DMA space.
Signed-off-by: NMatthew Daley <mattd@bugfuzz.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Always clear out these floppy_raw_cmd struct members after copying the
entire structure from userspace so that the in-kernel version is always
valid and never left in an interdeterminate state.
Signed-off-by: NMatthew Daley <mattd@bugfuzz.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This touchpad seriously dislikes init reports, not only timeing out, but
also refusing to work after this.

Cc: stable@vger.kernel.org
Reported-and-tested-by: NVincent Fortier <th0ma7@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The extra seven bits are only required when allocating the report buffer.
We can not use those extra bytes for the length of the report in the
generic implementation of .request because the device might (will) refuse
the set_report command.
This has been verified on the Atmel touchpad found on the Samsung Ativ 9
plus, which uses hid-multitouch and HID over I2C. Without this fix, the
device refuses to switch to the multitouch mode, and it becomes unresponsive
from the user point of view.

Actually, this has been discussed during the initial submission of the
commit 4fa5a7f7, see
https://patchwork.kernel.org/patch/3621751/

Unfortunately, I completely forgot about it later.
Reported-by: NMatthias Bayer <thematthiasbayer@gmail.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When building the name for the workqueue thread, make sure a format
string cannot leak in from the disk name.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The ubi->free_count should be updated with every insert/remove to/from
the ubi->free list.
Signed-off-by: NTanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: NDolev Raviv <draviv@codeaurora.org>
Acked-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

In case of an error (if there are not free PEB's for example),
__wl_get_peb will return a negative value. In order to prevent access
violation we need to test the returned value prior to using it later on.
Signed-off-by: NTatyana Brokhman <tlinder@codeaurora.org>
Reviewed-by: NDolev Raviv <draviv@codeaurora.org>
Acked-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

On 64 bit systems the agp_info struct has a 4 byte hole between
->agp_mode and ->aper_base.  We need to clear it to avoid disclosing
stack information to userspace.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Following arm64 commit bc3ee18a (arm64: init: Move of_clk_init to
time_init()), vexpress_osc_of_setup() is called via of_clk_init() long
before initcalls are issued. Initialising the vexpress oscillators
requires the vespress sysregs to be already initialised, so this patch
adds an explicit call to vexpress_sysreg_of_early_init() in vexpress
oscillator setup function.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Tested-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>