The em28xx driver have lots of different input types but
only 4 of such types are actually used. The others are bogus.

Remove them, in order to cleanup the driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch enables the tvp5150 decoder driver to be used with the media
controller framework by adding pad-level subdev operations and init the
media entity pad.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>

The tvp5150 output video is interlaced so mark the format
field as alternate and reduce the height to the half.

[javier: split patch and write commit message]
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>

This patch were a workaround for a regression at tvp5150, but
it causes troubles on devices with omap3+tvp5151 when working
in non-parallel bus mode.

Now that em28xx was fixed, we can get rid of that.

This reverts commit 47de9bf8.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

On em28xx driver, s_stream subdev ops was not implemented
properly. It was used only to disable stream, never enabling it.
That was the root cause of the regression when we added support
for s_stream on tvp5150 driver.

With that, we can get rid of the changes on tvp5150 side,
e. g. changeset 47de9bf8 ('[media] tvp5150: Fix breakage for serial usage').

Tested video output on em2820+tvp5150 on WinTV USB2 and
video and/or vbi output on em288x+tvp5150 on HVR 950.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

At least on Zotac CI321 ACPI provides an ioport range for the wake up part
but accessing these ioports has no effect.
Instead the ioport base address is set to another value already
(0xa20 in my case) and accessing this ioport range works.

Therefore set a new ioport base address only if the current ioport base
address is 0 (register reset default).

The need to use the existing base address instead of trying to set
an own one doesn't seem to be limited to this specific device as other
drivers like hwmon/nct6775 do it the same way.

This change was successfully tested on the mentioned device.
And the change should be generic enough to not break the driver for
other chips (however due to lack of appropriate hardware I wasn't
able to test this).

[mchehab@osg.samsung.com: Tested on Intel NUC NUC5i7RYB with BIOS
 version RYBDWi35.86A.0350.2015.0812.1722]
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Tested-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Calling nvt_set_cir_iren separately is not needed as this is done
by nvt_cir_regs_init.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Selecting the logical device in the interrupt handler is not needed
as no configuration register is accessed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Only enable the logical devices after the registers have been initialized.

The call to nvt_enable_logical_dev in nvt_resume is not needed as this is
done implicitely by nvt_cir_regs_init now.

[mchehab@osg.samsung.com: fixed multiline comment to kernel CodingStyle]
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Factor out enabling of a logical device.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Switch to using the recently introduced IR default timeout value
(IR_DEFAULT_TIMEOUT) and consider the value of SAMPLE_PERIOD
when calculating the limit count register value.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

At least on NVT6779D clearing the wake fifo works in learning mode only
(although this condition is not mentioned in the chip spec).
Setting the clear fifo bit has no effect in wake up mode.
Even if clearing the wake fifo should work in wake up mode on other
chips this workaround doesn't hurt.
If needed the caller of nvt_clear_cir_wake_fifo has to take care
of locking.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Factor out disabling of a logical device.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Simplify nvt_cir_tx_inactive.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use nvt_cr_write to simplify nvt_select_logical_ dev.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The two EFM ioports are accessed by drivers for other parts of the Nuvoton
Super-IO chips too. Therefore access to these ioports needs to be
protected by using request_muxed_region (like it's implemented e.g. in
hwmon/nct6775 already).
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This issue was detected by using the Coccinelle software.

Return the value from a call of the msi2500_ctrl_msg() function
without using an extra check for the variable "ret" at the end.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The variable "rc" will be set to an appropriate value from a call of
the r820t_set_tv_standard() function.
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This issue was detected by using the Coccinelle software.

1. Let us return directly if a call of the regmap_write() function failed.

2. Delete the jump label "err" then.

3. Return zero as a constant at the end.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This issue was detected by using the Coccinelle software.

1. Let us return directly if a call of the si2165_readreg8()
   function failed.

2. Reduce the scope for the local variables "ret" and "tmp" to one branch
   of an if statement.

3. Delete the jump label "err" then.

4. Return the value from a call of the si2165_writereg8() function
   without using an extra assignment for the variable "ret" at the end.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The ov2659 driver performs device detection and initialization in the
following way:
 - send reset command REG_SOFTWARE_RESET
 - load array of predefined register's setting (~150 values)
 - read device version REG_SC_CHIP_ID_H/REG_SC_CHIP_ID_L
 - check version and exit if invalid.

As result, for not connected device there will be >~150 i2c transactions
executed before device version checking and exit (there are no
failures detected because ov2659 declared as I2C_CLIENT_SCCB and NACKs
are ignored in this case).

Let's fix that by checking the chip version first and start
initialization only if it's supported.

Cc: Benoit Parrot <bparrot@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The data type "int" was used by the variable "ret" in the
gsc_m2m_poll() function despite of the aspect that the type "unsigned int"
will usually be needed for the return value from a call of the
v4l2_m2m_poll() function.
Improve this implementation detail by addition of the type modifier then.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

checkpatch complains about missing space around operators.

[mchehab@osg.samsung.com: removed obsolete hunks]
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

checkpatch complains about space after type cast.

[mchehab@osg.samsung.com: removed an obsolete hunk]
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

A NULL comparison can be written as if (var) or if (!var).
Reported by checkpatch.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add optional reset and standby gpios. The reset gpio is used to reset
the chip in power_on().

The standby gpio is not used currently. It is just unset, so the chip is
not in standby.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Passing a physical address to free_pages() is a bad idea.
config_params->fault_pxl.fpc_table_addr is set to virt_to_phys()
of __get_free_pages() return value; what we should pass to free_pages()
is its phys_to_virt().  ccdc_close() does that properly, but
ccdc_update_raw_params() doesn't.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

changeset 460b6c08 ("tvp5150: Add s_stream subdev operation
support") broke for em28xx-based devices with uses tvp5150. On those
devices, touching the TVP5150_MISC_CTL register causes em28xx to stop
streaming.

I suspect that it uses the 27 MHz clock provided by tvp5150 to feed
em28xx. So, change the logic to do nothing on s_stream if the tvp5150 is
not set up to work with V4L2_MBUS_PARALLEL.

Tested with Hauppauge WinTV USB 2 model 42012 Rev. C186
(USB ID: 2040:4200).

Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The si2165 does not support bandwidth auto-detection.
Reject the request.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Now that this was defined at usb-id.h, update the values for
USB_PID_TERRATEC_CINERGY_S2_R1 and USB_PID_TERRATEC_CINERGY_S2_R2.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Also Add Terratec Cinergy S2 usb id's
Signed-off-by: NBenjamin Larsson <benjamin@southpole.se>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The FIFO is used for ir_raw_event records, however for some historic
reason the FIFO is used on a per byte basis. IMHO this adds unneeded
complexity. Therefore set up the FIFO for ir_raw_event records.

This also allows to define the FIFO statically as part of
ir_raw_event_ctrl instead of having to allocate the FIFO dynamically.
In addition:

- When writing into the FIFO and it's full return ENOSPC instead of
  ENOMEM thus making it easier to tell between "FIFO full" and
  "Dynamic memory allocation failed" when the error is propagated to
  a higher level.
  Also add an error message.

- When reading from the FIFO check whether it's empty.
  This is not strictly needed here but kfifo_out is annotated
  "must check" anyway.

Successfully tested it with the nuvoton-cir driver.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

When requesting resources use different names for the normal and
the wakeup part. This makes it easier to interpret the output
of e.g. /proc/interrupts and /proc/ioports.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

MyGica/Geniatech S2870 is very similar to the S870 but with dual tuner. The card is recognised as Geniatech STK8096-PVR.

[mchehab@osg.samsung.com: Fix some checkpatch.pl issues]
Signed-off-by: NNicolas Sugino <nsugino@3way.com.ar>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Soon my dibcom.fr/parrot.com-address won't respond anymore.
Thus I'm replacing it. And, while being at it,
let's adapt some other (old) email-addresses as well.
Signed-off-by: NPatrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The Documentation/devicetree/bindings/media/i2c/tvp5150.txt DT binding doc
lists "ti,tvp5150" as the device compatible string but the driver does not
have an OF match table. Add the table to the driver so the I2C core can do
an OF style match.
Signed-off-by: NEduard Gavin <egavinc@gmail.com>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The video decoder supports either 8-bit 4:2:2 YUV with discrete syncs
or 8-bit ITU-R BT.656 with embedded syncs output format but currently
BT.656 it's always reported. Allow to configure the format to use via
either platform data or a device tree definition.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

After power-up, the tvp5150 decoder is in a unknown state until the
RESETB pin is driven LOW which reset all the registers and restarts
the chip's internal state machine.

The init sequence has some timing constraints and the RESETB signal
can only be used if the PDN (Power-down) pin is first released.

So, the initialization sequence is as follows:

1- PDN (active-low) is driven HIGH so the chip is power-up
2- A 20 ms delay is needed before sending a RESETB (active-low) signal.
3- The RESETB pulse duration is 500 ns.
4- A 200 us delay is needed for the I2C client to be active after reset.

This patch used as a reference the logic in the IGEPv2 board file from
the ISEE 2.6.37 vendor tree.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add a Device Tree binding document for the TVP5150 video decoder.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>