With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g.  64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring.  This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e.  When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state.  After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.

Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.

Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.

This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit -
"b852b720 gianfar: fix bug caused by
87c288c6"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.

Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.

This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Against -net.

In the patch "netpoll: re-enable irq in poll_napi()", I tried to
fix the following warning:

[100718.051041] ------------[ cut here ]------------
[100718.051048] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7d/0xb0()
(Not tainted)
[100718.051049] Hardware name: ProLiant BL460c G7
...
[100718.051068] Call Trace:
[100718.051073]  [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[100718.051075]  [<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[100718.051077]  [<ffffffff810747ed>] ? local_bh_enable_ip+0x7d/0xb0
[100718.051080]  [<ffffffff8150041b>] ? _spin_unlock_bh+0x1b/0x20
[100718.051085]  [<ffffffffa00ee974>] ? be_process_mcc+0x74/0x230 [be2net]
[100718.051088]  [<ffffffffa00ea68c>] ? be_poll_tx_mcc+0x16c/0x290 [be2net]
[100718.051090]  [<ffffffff8144fe76>] ? netpoll_poll_dev+0xd6/0x490
[100718.051095]  [<ffffffffa01d24a5>] ? bond_poll_controller+0x75/0x80 [bonding]
[100718.051097]  [<ffffffff8144fde5>] ? netpoll_poll_dev+0x45/0x490
[100718.051100]  [<ffffffff81161b19>] ? ksize+0x19/0x80
[100718.051102]  [<ffffffff81450437>] ? netpoll_send_skb_on_dev+0x157/0x240

by reenabling IRQ before calling ->poll, but it seems more
problems are introduced after that patch:

http://ozlabs.org/~akpm/stuff/IMG_20120824_122054.jpg
http://marc.info/?l=linux-netdev&m=134563282530588&w=2

So it is safe to fix be2net driver code directly.

This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.
Reported-by: NAndrew Morton <akpm@linux-foundation.org>
Reported-by: NSylvain Munaut <s.munaut@whatever-company.com>
Cc: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Tested-by: NSylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: NRayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sja1000 platform driver wrongly assumes that a shared IRQ is indicated
with the IRQF_SHARED flag in irq resource flags. This patch changes the
driver to handle the correct flag IORESOURCE_IRQ_SHAREABLE instead.

There are no mainline users of the platform driver which wrongly make use
of IRQF_SHARED.
Signed-off-by: NSven Schmitt <sven.schmitt@volkswagen.de>
Acked-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Do not leak memory by updating pointer with potentially NULL realloc return value.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

ETHTOOL_GRXCLSRULE returns filters for a TCP/IPv4 or UDP/IPv4 4-tuple
with source and destination swapped.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This patch fixes the name of the macro used to mask the
mmc interrupt: erroneously it was used: MMC_DEFAUL_MASK.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Erroneously the DWMAC_CORE_3_40 was set to 34 instead of 0x34.
This can generate problems when run on old chips because
the driver assumes that there are the extra 16 regs available
for perfect filtering.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.

Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:

    ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
    brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
    ieee80211 phy0: wl0: fatal error, reinitializing
    ieee80211 phy0: Hardware restart was requested
    ieee80211 phy0: brcms_ops_start: brcms_up() returned -19
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the device is not started, we can't read its
SRAM and attempting to do so will cause issues.
Protect the debugfs read.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_dbgfs_fh_reg_read() can cause crashes and/or
BUG_ON in slub because the ifdefs are wrong, the
code in iwl_dump_fh() should use DEBUGFS, not
DEBUG to protect the buffer writing code.

Also, while at it, clean up the arguments to the
function, some code and make it generally safer.

Cc: stable@vger.kernel.org
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The result of one call to a function is tested, and then at the second call
to the same function, the previous result, and not the current result, is
tested again.

Also changed &bssid to bssid, at the suggestion of Stanislav Yakovlev.

The semantic match that finds the first problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression ret;
identifier f;
statement S1,S2;
@@

*ret = f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S1
... when any
*f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S2
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch reduces the per rate target power eeprom reads for
AR5K_EEPROM_MODE_11A from 10 to 8, as there are only 8 valid
power curve entries on the eeprom. The former 10 reads lead to
equal max power limits per rate and this causes an increasing
distortion for all rates above 24 MBit and leads to a needless
poor performance in 802.11a mode.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This netconsole_target_put() is obviously redundant, and it
causes a kernel segfault when removing a bridge device which has
netconsole running on it.

This is caused by:

	commit 8d8fc29d
	Author: Amerigo Wang <amwang@redhat.com>
	Date:   Thu May 19 21:39:10 2011 +0000

	    netpoll: disable netpoll when enslave a device

Cc: David Miller <davem@davemloft.net>
 (for all 3.x stable releases)
Cc: stable@vger.kernel.org
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When getting clock, give a chance to the CPUs without DT support,
which use Common Clock Framework, such as Loongson1B.
Signed-off-by: NKelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e1,e2;
@@

if (ret < 0)
 { ... return ret; }
 ... when != ret = e1
     when forall
*if(...)
 {
  ... when != ret = e2
* return ret;
 }
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move up the initialization of rc so that failure of pci_alloc_consistent
returns -ENOMEM as well.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e1,e2;
@@

if (ret < 0)
 { ... return ret; }
 ... when != ret = e1
     when forall
*if(...)
 {
  ... when != ret = e2
* return ret;
 }
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e1,e2;
@@

if (ret < 0)
 { ... return ret; }
 ... when != ret = e1
     when forall
*if(...)
 {
  ... when != ret = e2
* return ret;
 }
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer firmware versions for the Pantech UML290 use a different
subclass ID.  The Windows driver match on both IDs, so we do
that as well.

The ZTE (Vodafone) K5006-Z is a new device.

Cc: Dan Williams <dcbw@redhat.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mdio-mux driver scans all child mdio nodes, without regard to whether
the node is actually used.  Some device trees include all possible
mdio-mux nodes and rely on the boot loader to disable those that are not
present, based on some run-time configuration.  Those nodes need to be
skipped.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.

Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Reported-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Herton Ronaldo Krzesinski <herton@canonical.com>
CC: Hin-Tak Leung <htl10@users.sourceforge.net>
CC: Larry Finger <Larry.Finger@lwfinger.net>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.

Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Reported-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Christian Lamparter <chunkeey@googlemail.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

 - Use kcalloc() / vzalloc() instead of an extra bitmap_zero().
 - Add __GFP_NOWARN to kcalloc() since we'll try vzalloc() if it fails.
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix some issues around int variables used in data structures related
to memory registration.

Handle int overflow in mlx4_init_icm_table by using a u64 intermediate
variable and changing struct mlx4_icm_table num_obj field to be u32.

Change some more fields/variables to use u32 instead of int to prevent
a case where the variable becomes negative when bit 31 is set.

Also subtract log_mtts_per_seg from the exponent when computing
num_mtt, since its added later on in that very same code area.

This and the previous commit fixes some issues which actually prevent
commit db5a7a65 ("mlx4_core: Scale size of MTT table with system
RAM") from working.  Now, when the number of MTTs is scaled with the
size of the RAM we can map up to 8TB.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

mlx4_buddy_init uses kmalloc() to allocate bitmaps, which fails when
the required size is beyond the max supported value (or when memory is
too fragmented to handle a huge allocation).  Extend this to use use
vmalloc() if kmalloc() fails, and take that into account when freeing
the bitmaps as well.

This fixes a driver load failure when log num mtt is 26 or higher, and
is a step in the direction of allowing to register huge amounts of
memory on large memory systems.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

dev_open() can complete before register_netdev() returns.
Fix vmxnet3_probe_device() to support this.
Signed-off-by: NSteve Hodgson <steve@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a 0 error return code to a negative one, as returned elsewhere in the
function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a 0 error return code to a negative one, as returned elsewhere in the
function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.

The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E
      when != i
  if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take advantage of the matching macros to make the device id
list easier to read and maintain.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 6 new devices and one modified device, based on
information from laptop vendor Windows drivers.

Sony provides a driver with two new devices using
a Gobi 2k+ layout (1199:68a5 and 1199:68a9).  The
Sony driver also adds a non-standard QMI/net
interface to the already supported 1199:9011
Gobi device. We do not know whether this is an
alternate interface number or an additional
interface which might be present, but that doesn't
really matter.

Lenovo provides a driver supporting 4 new devices:
 - MC7770 (1199:901b) with standard Gobi 2k+ layout
 - MC7700 (0f3d:68a2) with layout similar to MC7710
 - MC7750 (114f:68a2) with layout similar to MC7710
 - EM7700 (1199:901c) with layout similar to MC7710

Note regaring the three devices similar to MC7710:

The Windows drivers only support interface #8 on these
devices.  The MC7710 can support QMI/net functions on
interface #19 and #20 as well, and this driver is
verified to work on interface #19 (a firmware bug is
suspected to prevent #20 from working).

We do not enable these additional interfaces until they
either show up in a Windows driver or are verified to
work in some other way.  Therefore limiting the new
devices to interface #8 for now.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver support many composite USB devices where the
interface class/subclass/protocol provides no information
about the interface function. Interfaces with different
functions may all use ff/ff/ff, like this example of
a device with three serial interfaces and three QMI/wwan
interfaces:

T:  Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1199 ProdID=68a2 Rev= 0.06
S:  Manufacturer=Sierra Wireless, Incorporated
S:  Product=MC7710
S:  SerialNumber=3581780xxxxxx
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

Instead of class/subclass/protocol the vendor use fixed
interface numbers for each function, and the Windows
drivers use these numbers to match driver and function.

The driver has had its own interface number whitelisting
code to simulate this functionality.  Replace this with
generic interface number matching now that the USB subsystem
support is there. This
 - removes the need for a driver_info structure per
   interface number,
 - avoids running the probe function for unsupported
   interfaces, and
 - simplifies the code.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although this doesn't matter actually, because netpoll_tx_running()
doesn't use the parameter, the code will be more readable.

For team_dev_queue_xmit() we have to move it down to avoid
compile errors.

Cc: David Miller <davem@davemloft.net>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the previous patch applied, __netpoll_cleanup() is non-block now,
so we don't need to release the spin_lock before calling it.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like the previous patch, slave_disable_netpoll() and __netpoll_cleanup()
may be called with read_lock() held too, so we should make them
non-block, by moving the cleanup and kfree() to call_rcu_bh() callbacks.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>