- Added logic to initiate a PLOGI to the target, while processing a LOGO
  from the same target in Direct attach mode.
- Added logic to generate a FCCT Reject indicating unsupported command,
  upon receiving FCCT/FCGS requests.
- Added logic to set the fcpim in offline state and avoid any PRLI retries
  if a PRLI response is a reject with a reason Command Not Supported.
- Updated the FDMI Supported/Current speeds.
- Added logic to wait for the response  from the firmware before sending
  ACC to PLOGI and transitioning to subsequent states - while processing an
  Incoming PLOGI in online state.
- Added a wait state in the fcs_vport state machine - For case where
  FDISC is in progress and we get a vport delete request we wait for
  fdisc response and will transition to the appropriate state based on
  rsp status, else its causing both driver/fw resources to be not
  freed.
- Remove the fc_credit_recovery module param.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Modified the design such that each BFA sub-module will provide
  the amount of DMA and KVA memory needed by it and queues the
  same request to the global dma and kva info queues.
- During the memory allocation we iterate over this queue to allocate
  the dma and kva memory requested by sub-modules.
- The change is needed to avoid requesting the aggregate amount of memory
  needed by all the BFA sub-modules as one contiguous chunk.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Introduced partitioning of the BFA resources.
- Added h/w queue ID in CPE messages, firmware uses h/w queue ID
  from messages to pick a matching RME queue.
- Added message header to bfa_reqq_produce(). h/w queue ID is set
  in the message header and firmware modules use h/w queue ID from
  message header instead of from cpqe event.
- Made changes to allow using all 256 queues of Brocade-1860 asic.
  Previously only a single queue per queue group was used.
- Added function tag to BFI message header. Only used by FC BFI
  messages.  Used to translate host tag to firmware tag. bfa_lpuid()
  is changed to bfa_fn_lpu() that encodes both PCI function and port
  ID in BFI message header.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Updated/added data structures and definitions to support FAA protocol.
- Modified the IOC state machine to support FAA.
- Introduced FAA feature configuration - enable/disable/query.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Introduce FC credit recovery.
- Added module parameter to enable/disable credit recovery.

Bug Fixes:
- Removed check for ignoring plogi from initiator in switched fabric mode.
- The ABTS for PLOGI is going out few millisecs earlier due to FW
  timer calibration (around 300 miilisecs earlier). So there is a
  window if an accept comes during this time HBA would have initiated
  an ABORT.
- Added 1 to FC_ELS_TOV for compensating for FW timer.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Add PBC port Disabled condition check.
- Rename incorrectly named LPS I2H messages.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Avoid the use of hardware defined structure bfi_sge_s for DMA
  requests in host.

- Defined a generic address len pair to represent a DMA memory chunk
  (bfi_alen_s).
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

This patch removes unused functions, data strucutres, and definitions.  It
also includes misc comment and formatting cleanups.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch removes some inactive functions and macros.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Direct attach is not working due to the check of PID in fcxp_send request.
- Added logic to set the lps->lp_pid with the PID assigned for n2n mode.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When the bfa driver is loaded a flogi is sent without the knowledge of
trunking configuration. This normal flogi causes the switch ports
which had trunking enabled to go to persistent offline.  Solution is
to store the port configuration (which has trunking info) in the flash
for persistency. The firmware will read this configuration when the
very first fcport enable is received.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Remove unused functions and fix checkpatch errors. Misc cleanups in
comment and formatting.
Signed-off-by: NMaggie Zhang <xmzhang@brocade.com>
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Remove OS wrapper functions/macros, and as a result remove bfa_os_inc.h.
Signed-off-by: NMaggie Zhang <xmzhang@brocade.com>
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Cleaned up one line functions.
Signed-off-by: NMaggie Zhang <xmzhang@brocade.com>
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Removed unused and empty functions.
Signed-off-by: NMaggie Zhang <xmzhang@brocade.com>
Signed-off-by: NJing Huang <xmzhang@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__".
Signed-off-by: NMaggie <xmzhang@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Rename log_level to bfa_log_level to make the global variable more bfa
specific and avoid clashes with other drivers which was causing a
build failure.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch addresses the comments from Randy Dunlap (Randy.Dunlap@oracle.com)
regarding comment blocks that begining with "/**". bfa driver comments
currently do not follow kernel-doc convention, we hence replace all
/** with /* and **/ with */.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch removes os wrapper and unused functions.
bfa_os_assign(), bfa_os_memset(), bfa_os_memcpy(), bfa_os_udelay()
bfa_os_vsprintf(), bfa_os_snprintf(), and bfa_os_get_clock() are replaced with
direct assignment or native linux functions. Some unused functions related to VF
(Vitual fabric) are also removed.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

We have flattened the BFA hierarchy and also reduced the number of
source and header files we used to have earlier.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>