System crash was observed if one of the driver initialisation
commands is timed out. The reason is our timeout handler triggers
firmware dump, meanwhile driver initialisation error paths have
already freed the adapter structure.

Firmware hasn't yet completely initialized. So collecting firmware
dump is not needed in this case. Command timeout handler is
modified in this patch to fix the crash issue.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When WLAN interface is up and running, driver unload and
load was causing command timeout error.

We enable Rx data by updating RX ring read pointer in
init_fw_port(). It should be done when FW is completely
intialialised. Command timeout is fixed in this patch by
moving init_fw_port() call to mwifiex_init_fw_complete().
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Variable pos is u8 here, so memcpy is needed to store u16 aid.
At the same time, aid should be platform independent, upper layer
utility(wpa_supplicant,etc.,) parse it as le16, so keep it le16
here.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use list_empty(&tid->list) instead
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

struct ath_atx_ac contains a list of active TIDs belonging to one WMM AC.
This patch changes the code to track active station TIDs in the txq directly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Setup rxfiler correctly for offchannel ctx.

This fix problem we didn't configure rxfilter, next
didn't receive probe requests and next failed
p2p_find. This was seen when ath9k loaded with
use_chanctx=1
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

While mac80211 setup this per HW, set same
rxfilter configuration for all chanctx.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In case we will get ROC cancel from mac80211 we
should not call ieee80211_remain_on_channel_expired().

In other case I hit such warning on MIPS and
p2p negotiation failed (tested with use_chanctx=1).

ath: phy0: Starting RoC period
ath: phy0: Channel definition created: 2412 MHz
ath: phy0: Assigned next_chan to 2412 MHz
ath: phy0: Offchannel duration for chan 2412 MHz : 506632
ath: phy0: ath_chanctx_set_next: current: 2412 MHz, next: 2412 MHz
ath: phy0: Stopping current chanctx: 2412
ath: phy0: Flush timeout: 200
ath: phy0: ath_chanctx_set_next: Set channel 2412 MHz
ath: phy0: Set channel: 2412 MHz width: 0
ath: phy0: Reset to 2412 MHz, HT40: 0 fastcc: 0
ath: phy0: cur_chan: 2412 MHz, event: ATH_CHANCTX_EVENT_TSF_TIMER, state: ATH_CHANCTX_STATE_IDLE
ath: phy0: ath_offchannel_channel_change: offchannel state: ATH_OFFCHANNEL_ROC_START
ath: phy0: cur_chan: 2412 MHz, event: ATH_CHANCTX_EVENT_SWITCH, state: ATH_CHANCTX_STATE_IDLE
ath: phy0: Cancel RoC
ath: phy0: RoC aborted
ath: phy0: RoC request on vif: 00:03:7f:4e:a0:cd, type: 1 duration: 500
ath: phy0: Starting RoC period
ath: phy0: Channel definition created: 2412 MHz
ath: phy0: Assigned next_chan to 2412 MHz
ath: phy0: Offchannel duration for chan 2412 MHz : 506705
ath: phy0: ath_chanctx_set_next: current: 2412 MHz, next: 2412 MHz
ath: phy0: ath_offchannel_channel_change: offchannel state: ATH_OFFCHANNEL_ROC_START
ath: phy0: cur_chan: 2412 MHz, event: ATH_CHANCTX_EVENT_SWITCH, state: ATH_CHANCTX_STATE_IDLE
------------[ cut here ]------------
WARNING: CPU: 0 PID: 3312 at drivers/net/wireless/ath/ath9k/main.c:2319
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Advertise p2p device support when ath9k loaded with
use_chanctx=1.

This will fix problem, when first interface is an AP
and next we would like to run p2p_find.
Before p2p find (scan phase) failed with EOPNOTSUPP.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

600f5d90("mwifiex: cleanup ioctl wait queue and abstraction layer")
introduced the wakeup_interruptible suppression in mwifiex_complete_cmd
b1a47aa5("mwifiex: fix system hang issue in cmd timeout error case")
then added wakup_interruptible to mwifiex_cmd_timeout_func the single
place setting a status of ETIMEDOUT.
Instead of doing extra work, using the standard call-chain will have the
same effect:
mwifiex_cancel_pending_ioctl
-> mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd
-> wake_up_interruptible

The difference is that previously the condition was not set to true,
but that's probably just an oversight in b1a47aa5 and shouldn't
have any consequence
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

CMD_F_CANCELED was used to abort mwifiex_process_cmdresp in
case it already started or starts processing the cmd.
But this was probably not working the way intended:
- it is racy: mwifiex_process_cmdresp might already have passed that
  test and is continuing to use the cmd node being recycled
- mwifiex_process_cmdresp repeatedly uses adapter->curr_cmd which
  we just set to NULL
- mwifiex_recycle_cmd_node will clear the flag

The reason why it probably works is that mwifiex_cancel_pending_ioctl
is only called from mwifiex_cmd_timeout_func, where the there is little
chance of a command response still arriving
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

mwifiex_cancel_pending_ioctl is called only from
mwifiex_cmd_timeout_func. There the wait_q status is set to
-ETIMEDWAIT before calling this function. Whether we reset the status
to -1 or leave it at -ETIMEDWAIT at end doesn't matter since both
are != 0 hence mean failure
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

standard call chain when releasing a cmd node:
mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd, if wait_q_enabled

calling mwifiex_complete_cmd explicitly and setting
wait_q_enabled = false is redundant
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since 1fb654fd("mmc: sdio: add reset callback to bus operations"),
sdio cards can be power cycled using mmc_hw_reset.
The use mmc_remove_host/mmc_add_host is discouraged, because these are
internal functions to the mmc core and should only be used by mmc hosts
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next, they are:

1) A couple of cleanups for the netfilter core hook from Eric Biederman.

2) Net namespace hook registration, also from Eric. This adds a dependency with
   the rtnl_lock. This should be fine by now but we have to keep an eye on this
   because if we ever get the per-subsys nfnl_lock before rtnl we have may
   problems in the future. But we have room to remove this in the future by
   propagating the complexity to the clients, by registering hooks for the init
   netns functions.

3) Update nf_tables to use the new net namespace hook infrastructure, also from
   Eric.

4) Three patches to refine and to address problems from the new net namespace
   hook infrastructure.

5) Switch to alternate jumpstack in xtables iff the packet is reentering. This
   only applies to a very special case, the TEE target, but Eric Dumazet
   reports that this is slowing down things for everyone else. So let's only
   switch to the alternate jumpstack if the tee target is in used through a
   static key. This batch also comes with offline precalculation of the
   jumpstack based on the callchain depth. From Florian Westphal.

6) Minimal SCTP multihoming support for our conntrack helper, from Michal
   Kubecek.

7) Reduce nf_bridge_info per skbuff scratchpad area to 32 bytes, from Florian
   Westphal.

8) Fix several checkpatch errors in bridge netfilter, from Bernhard Thaler.

9) Get rid of useless debug message in ip6t_REJECT, from Subash Abhinov.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it similar to reject_tg() in ipt_REJECT.
Suggested-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Hariprasad Shenai says:

====================
add meminfo, bist status and misc. fixes

This patch series adds the following.
Add support to dump memory address range of various hw modules
Add support to dump edc bist status during ecc error
Read correct bits of who am i register for T6 adapter
and update T6 register range

This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.

V2: PATCH 3/4 ("cxgb4/cxgb4vf: read the correct bits of PL Who Am I
    register") Fix switch statement in get_chip_type() and some more style
    fixes based on review comment by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read the correct bits of PL Who Am I for the Source PF field which has
changed in T6
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to dump edc bist status for ECC data errors
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add debug support to dump memory address ranges of various hardware
modules of the adapter.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In multiple locations there are checks for whether the label in hand
is a reserved label or not using the arbritray value of 16. Factor
this out into a #define for better maintainability and for
documentation.
Signed-off-by: NRobert Shearman <rshearma@brocade.com>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Robert Shearman says:

====================
lwtunnel: encap locally-generated ipv4 packets

Locally-generated IPv4 packets, such as from applications running on
the host or traceroute/ping currently don't have lwtunnel output
redirected encap applied. However, they should do in the same way as
for forwarded packets and this patch series addresses that.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lwtunnel encap is applied for forwarded packets, but not for
locally-generated packets. This is because the output function is not
overridden in __mkroute_output, unlike it is in __mkroute_input.

The lwtunnel state is correctly set on the rth through the call to
rt_set_nexthop, so all that needs to be done is to override the dst
output function to be lwtunnel_output if there is lwtunnel state
present and it requires output redirection.
Signed-off-by: NRobert Shearman <rshearma@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the locally-generated packet path skb->protocol may not be set and
this is required for the lwtunnel encap in order to get the lwtstate.

This would otherwise have been set by ip_output or ip6_output so set
skb->protocol prior to calling the lwtunnel encap
function. Additionally set skb->dev in case it is needed further down
the transmit path.
Signed-off-by: NRobert Shearman <rshearma@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of trying to access br->vlan_enabled directly use the provided
helper br_vlan_enabled().
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the introduction of the BPF action in d23b8ad8 ("tc: add BPF
based action"), late binding was not working as expected. I.e. setting
the action part for a classifier only via 'bpf index <num>', where <num>
is the index of an existing action, is being rejected by the kernel due
to other missing parameters.

It doesn't make sense to require these parameters such as BPF opcodes
etc, as they are not going to be used anyway: in this case, they're just
allocated/parsed and then freed again w/o doing anything meaningful.

Instead, parse and verify the remaining parameters *after* the test on
tcf_hash_check(), when we really know that we're dealing with creation
of a new action or replacement of an existing one and where late binding
is thus irrelevant.

After patch, test case is now working:

  FOO="1,6 0 0 4294967295,"
  tc actions add action bpf bytecode "$FOO"
  tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action bpf index 1
  tc actions show action bpf
    action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
    index 1 ref 2 bind 1
  tc filter show dev foo
    filter protocol all pref 49152 bpf
    filter protocol all pref 49152 bpf handle 0x1 flowid 1:1 bytecode '1,6 0 0 4294967295'
    action order 1: bpf bytecode '1,6 0 0 4294967295' default-action pipe
    index 1 ref 2 bind 1

Late binding of a BPF action can be useful for preloading maps (e.g. before
they hit traffic) in case of eBPF programs, or to share a single eBPF action
with multiple classifiers.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At switch setup, _mv88e6xxx_stats_wait was called without holding the
SMI mutex. Fix this by requesting the lock for this call.

Also, return the _mv88e6xxx_stats_wait code, since it may fail.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch when a vid was not specified, the entry was added with
vid 0 which is useless when vlan_filtering is enabled. This patch makes
the entry to be added on all configured vlans when vlan filtering is
enabled and respectively deleted from all, if the entry vid is 0.
This is also closer to the way fdb works with regard to vid 0 and vlan
filtering.

Example:
Setup:
$ bridge vlan add vid 256 dev eth4
$ bridge vlan add vid 1024 dev eth4
$ bridge vlan add vid 64 dev eth3
$ bridge vlan add vid 128 dev eth3
$ bridge vlan
port	vlan ids
eth3	 1 PVID Egress Untagged
	 64
	 128

eth4	 1 PVID Egress Untagged
	 256
	 1024
$ echo 1 > /sys/class/net/br0/bridge/vlan_filtering

Before:
$ bridge mdb add dev br0 port eth3 grp 239.0.0.1
$ bridge mdb
dev br0 port eth3 grp 239.0.0.1 temp

After:
$ bridge mdb add dev br0 port eth3 grp 239.0.0.1
$ bridge mdb
dev br0 port eth3 grp 239.0.0.1 temp vid 1
dev br0 port eth3 grp 239.0.0.1 temp vid 128
dev br0 port eth3 grp 239.0.0.1 temp vid 64
Signed-off-by: NSatish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Toshiaki Makita says:

====================
Stacked vlan TSO for virtual devices

Basically virtual devices do not need to segment double tagged packets.
This patch set adds TSO feature for double tagged packets to several
virtual devices, which can be realized by simply setting
.ndo_features_check to passthru_features_check.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tap devices don't need to segment multiple tagged packets.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bridge devices don't need to segment multiple tagged packets since thier
ports can segment them.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Veth devices don't need to segment multiple tagged packets.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macvlan/macvtap devices don't need to segment multiple tagged packets
since the lower devices can segment them.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Straightforward patch to add GRO processing to virtio_net.

napi_complete_done() usage allows more aggressive aggregation,
opted-in by setting /sys/class/net/xxx/gro_flush_timeout

Tested:

Setting /sys/class/net/xxx/gro_flush_timeout to 1000 nsec,
Rick Jones reported following results.

One VM of each on a pair of OpenStack compute nodes with E5-2650Lv3 CPUs
and Intel 82599ES-based NICs. So, two "before" and two "after" VMs.
The OpenStack compute nodes were running OpenStack Kilo, with VxLAN
encapsulation being used through OVS so no GRO coming-up the host
stack.  The compute nodes themselves were running a 3.14-based kernel.

Single-stream netperf, CPU utilizations and thus service demands are
based on intra-guest reported CPU.

Throughput Mbit/s, bigger is better
        Min     Median  Average Max
4.2.0-rc3+      1364    1686    1678    1938
4.2.0-rc3+flush1k       1824    2269    2275    2647

Send Service Demand, smaller is better
        Min     Median  Average Max
4.2.0-rc3+      0.236   0.558   0.524   0.802
4.2.0-rc3+flush1k       0.176   0.503   0.471   0.738

Receive Service Demand, smaller is better.
        Min     Median  Average Max
4.2.0-rc3+      1.906   2.188   2.191   2.531
4.2.0-rc3+flush1k       0.448   0.529   0.533   0.692
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NRick Jones <rick.jones2@hp.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suggested-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rocker supports the transmission of scattered packets, so let the kernel
know about it by setting the NETIF_F_SG bit in the device's features.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add skb->hash to the __sk_buff offset map, so it can be accessed from
an eBPF program. We currently already do this for classic BPF filters,
but not yet on eBPF, it might be useful as a demuxer in combination with
helpers like bpf_clone_redirect(), toy example:

  __section("cls-lb") int ingress_main(struct __sk_buff *skb)
  {
    unsigned int which = 3 + (skb->hash & 7);
    /* bpf_skb_store_bytes(skb, ...); */
    /* bpf_l{3,4}_csum_replace(skb, ...); */
    bpf_clone_redirect(skb, which, 0);
    return -1;
  }

I was thinking whether to add skb_get_hash(), but then concluded the
raw skb->hash seems fine in this case: we can directly access the hash
w/o extra eBPF helper function call, it's filled out by many NICs on
ingress, and in case the entropy level would not be sufficient, people
can still implement their own specific sw fallback hash mix anyway.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 05cc5a39 ("bnx2x: add vlan filtering offload") has introduced
an incorrect logic for checking whether pvid should be configured for
a vf, causing the hypervisor driver to send unneeded ramrods for all of
the vfs each time a pvid has changed.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>