Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Original patch from Ian Dall in bugzilla. Set command timeout as
specified by the SCSI layer rather than hardcode it to 30 seconds. I
have received a couple of reports of people hitting this one with
various tape configurations and the patch looks obviously correct.
                                                                  - Jes

From http://bugzilla.kernel.org/show_bug.cgi?id=6275

ian@beware.dropbear.id.au (Ian Dall):

The command sent to the card was using a 30second timeout regardless of the
timeout requested in the scsi command passed down from higher levels.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

aic94xx relies on external firmware and thus requires FW_LOADER.
Signed-off-by: NMuli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This sg driver patch addresses the problem with larger
page sizes reported by Brian King in this post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115867718623631&w=2
Some other related matters are also addressed. Some of these
prevent oopses when the SG_SCATTER_SZ or scatter_elem_sz are
set to inappropriate values.

The scatter_elem_sz has been tested up to 4 MB which should
make the largest data transfer with one SCSI command, 32 MB
less one block, achievable with a relatively small number
of elements in the scatter gather list.

ChangeLog:
    - add scatter_elem_sz boot time parameter and sysfs module
      parameter that is initialized to SG_SCATTER_SZ
    - the driver will then adjust scatter_elem_sz to be the
      max(given(scatter_elem_sz), PAGE_SIZE)
      It will also round it up, if necessary, to be a power
      of two
    - clean up sg.h header, correct bad urls and some statements
      that are no longer valid
    - make the def_reserved_size sysfs module attribute writable
Signed-off-by: NDouglas Gilbert <dougg@torque.net>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Convert cmm's usage of kernel_thread to kthread_run.  Also create the
cmmthread at module load time, so it is possible to check if creation of
the thread fails.

In addition the cmmthread now gets terminated when the module gets unloaded
instead of leaving a stale kernel thread.  Also check the return values of
other registration functions at module load and handle their return values
appropriately.

Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Include the host architecture's ptrace-abi.h instead of ptrace.h.

There was some cpp mangling of names around the ptrace.h include to avoid
symbol clashes between UML and the host architecture.  Most of these can go
away.  The exception is struct pt_regs, which is convenient to have in
userspace, but must be renamed in order that UML can define its own.

ptrace-x86_64.h needed to have some now-obsolete cpp cruft and a declaration
removed.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The use of SEGMENT_RPL_MASK in the i386 ptrace.h introduced by
x86-allow-a-kernel-to-not-be-in-ring-0.patch broke the UML build, as UML
includes the underlying architecture's ptrace.h, but has no easy access to the
x86 segment definitions.

Rather than kludging around this, as in the past, this patch splits the
userspace-usable parts, which are the bits that UML needs, of ptrace.h into
ptrace-abi.h, which is included back into ptrace.h.  Thus, there is no net
effect on i386.

As a side-effect, this creates a ptrace header which is close to being usable
in /usr/include.

x86_64 is also treated in this way for consistency.  There was some trailing
whitespace there, which is cleaned up.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Ensure current->signal->tty doesn't get freed during log_exec().
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The KSTK_* macros used an inordinate amount of stack.  In order to overcome
an impedance mismatch between their interface, which just returns a single
register value, and the interface of get_thread_regs, which took a full
pt_regs, the implementation created an on-stack pt_regs, filled it in, and
returned one field.  do_task_stat calls KSTK_* twice, resulting in two
local pt_regs, blowing out the stack.

This patch changes the interface (and name) of get_thread_regs to just
return a single register from a jmp_buf.

The include of archsetjmp.h" in registers.h to get the definition of
jmp_buf exposed a bogus include of <setjmp.h> in start_up.c.  <setjmp.h>
shouldn't be used anywhere any more since UML uses the klibc
setjmp/longjmp.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean set_ether_mac usage.  Maybe could also be removed, but surely it can't
be a global function taking a void* argument.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: NJeff Dike <jdike@addtoit.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

timer_irq_inited was useless, so it is removed.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

set_interval returns an error instead of panicing if setitimer fails.  Some of
its callers now check the return.

enable_timer is largely tt-mode-specific, so it is marked as such, and the
only skas-mode caller is made to call set-interval instead.

user_time_init was a no-value-added wrapper around set_interval, so it is
gone.

Since set_interval is now called from kernel code, callers no longer pass
ITIMER_* to it.  Instead, they pass a flag which is converted into ITIMER_REAL
or ITIMER_VIRTUAL.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Have most signals go through an arch-provided handler which recovers the
sigcontext and then calls a generic handler.  This replaces the
ARCH_GET_SIGCONTEXT macro, which was somewhat fragile.  On x86_64, recovering
%rdx (which holds the sigcontext pointer) must be the first thing that
happens.  sig_handler duly invokes that first, but there is no guarantee that
I can see that instructions won't be reordered such that %rdx is used before
that.  Having the arch provide the handler seems much more robust.

Some signals in some parts of UML require their own handlers - these places
don't call set_handler any more.  They call sigaction or signal themselves.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Various cleanups in the sigio code.

- Removed explicit zero-initializations of a few structures.

- Improved some error messages.

- An API change - there was an asymmetry between reactivate_fd calling
  maybe_sigio_broken, which goes through all the machinery of figuring out if
  a file descriptor supports SIGIO and applying the workaround to it if not,
  and deactivate_fd, which just turns off the descriptor.

  This is changed so that only activate_fd calls maybe_sigio_broken, when
  the descriptor is first seen.  reactivate_fd now calls add_sigio_fd, which
  is symmetric with ignore_sigio_fd.

  This removes a recursion which makes a critical section look more critical
  than it really was, obsoleting a big comment to that effect.  This requires
  keeping track of all descriptors which are getting the SIGIO treatment, not
  just the ones being polled at any given moment, so that reactivate_fd,
  through add_sigio_fd, doesn't try to tell the SIGIO thread about descriptors
  it doesn't care about.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

UML can get a SIGBUS anywhere if the tmpfs mount being used for its memory
runs out of space.  This patch adds a printk before the panic to provide a
clue as to what likely went wrong.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There were some bugs in handling failures to exec helper programs.  errno was
passed back from the child with the wrong sign.  It was also ignored.  In the
case where it mattered, the errno from the (successful) read in the parent was
used instead.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

arch/um/kernel/tlb.c had some pretty serious whitespace problems.  I also
fixed some returns.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Stack randomization needs to be conditional on the personality allowing it.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There were a bunch of missed ARRAY_SIZE opportunities.

Also, some formatting fixes in the affected areas of code.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds an implementation of setjmp and longjmp to UML, allowing
access to the inside of a jmpbuf without needing the access macros formerly
provided by libc.

The implementation is stolen from klibc.  I copy the relevant files into
arch/um.  I have another patch which avoids the copying, but requires klibc be
in the tree.

setjmp and longjmp users required some tweaking.  Includes of <setjmp.h> were
removed and includes of the UML longjmp.h were added where necessary.  There
are also replacements of siglongjmp with UML_LONGJMP which I somehow missed
earlier.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add the pm_trace attribute in /sys/power which has to be explicitly set to
one to really enable the "PM tracing" code compiled in when CONFIG_PM_TRACE
is set (which modifies the machine's CMOS clock in unpredictable ways).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Detect the situations in which the time after a resume from disk would be
earlier than the time before the suspend and prevent them from happening on
i386.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Hack uart_suspend_port() and uart_resume_port() so that serial console
ports are not suspended if CONFIG_DISABLE_CONSOLE_SUSPEND is set.

This makes it possible to debug the suspend and resume routines of all
device drivers as well as the lowest-level swsusp code with the help of the
serial console.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Change suspend_console() so that it waits for all consoles to flush the
remaining messages and make it possible to switch the console suspending off
with the help of a Kconfig option.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Stefan Seyfried <seife@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make swsusp use memory bitmaps to store its internal information during the
resume phase of the suspend-resume cycle.

If the pfns of saveable pages are saved during the suspend phase instead of
the kernel virtual addresses of these pages, we can use them during the resume
phase directly to set the corresponding bits in a memory bitmap.  Then, this
bitmap is used to mark the page frames corresponding to the pages that were
saveable before the suspend (aka "unsafe" page frames).

Next, we allocate as many page frames as needed to store the entire suspend
image and make sure that there will be some extra free "safe" page frames for
the list of PBEs constructed later.  Subsequently, the image is loaded and, if
possible, the data loaded from it are written into their "original" page
frames (ie.  the ones they had occupied before the suspend).

The image data that cannot be written into their "original" page frames are
loaded into "safe" page frames and their "original" kernel virtual addresses,
as well as the addresses of the "safe" pages containing their copies, are
stored in a list of PBEs.  Finally, the list of PBEs is used to copy the
remaining image data into their "original" page frames (this is done
atomically, by the architecture-dependent parts of swsusp).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Introduce the memory bitmap data structure and make swsusp use in the suspend
phase.

The current swsusp's internal data structure is not very efficient from the
memory usage point of view, so it seems reasonable to replace it with a data
structure that will require less memory, such as a pair of bitmaps.

The idea is to use bitmaps that may be allocated as sets of individual pages,
so that we can avoid making allocations of order greater than 0.  For this
reason the memory bitmap structure consists of several linked lists of objects
that contain pointers to memory pages with the actual bitmap data.  Still, for
a typical system all of these lists fit in a single page, so it's reasonable
to introduce an additional mechanism allowing us to allocate all of them
efficiently without sacrificing the generality of the design.  This is done
with the help of the chain_allocator structure and associated functions.

We need to use two memory bitmaps during the suspend phase of the
suspend-resume cycle.  One of them is necessary for marking the saveable
pages, and the second is used to mark the pages in which to store the copies
of them (aka image pages).

First, the bitmaps are created and we allocate as many image pages as needed
(the corresponding bits in the second bitmap are set as soon as the pages are
allocated).  Second, the bits corresponding to the saveable pages are set in
the first bitmap and the saveable pages are copied to the image pages.
Finally, the first bitmap is used to save the kernel virtual addresses of the
saveable pages and the second one is used to save the contents of the image
pages.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Introduce some constants that hopefully will help improve the readability of
code in kernel/power/snapshot.c.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The name of the pagedir_nosave variable does not make sense any more, so it
seems reasonable to change it to something more meaningful.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove some things that are no longer used or defined elsewhere from suspend.h
and make the inline version of software_suspend() return the right error code.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Get rid of the FIXME in kernel/power/snapshot.c#alloc_pagedir() and
simplify the functions called by it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Move some functions in kernel/power/snapshot.c to a better place (in the
same file) and introduce free_image_page() (will be necessary in the
future).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean up mm/page_alloc.c#mark_free_pages() and make it avoid clearing
PageNosaveFree for PageNosave pages.  This allows us to get rid of an ugly
hack in kernel/power/snapshot.c#copy_data_pages().

Additionally, the page-copying loop in copy_data_pages() is moved to an
inline function.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The current suspend code has to be run on one CPU, so we use the CPU
hotplug to take the non-boot CPUs offline on SMP machines.  However, we
should also make sure that these CPUs will not be enabled by someone else
after we have disabled them.

The functions disable_nonboot_cpus() and enable_nonboot_cpus() are moved to
kernel/cpu.c, because they now refer to some stuff in there that should
better be static.  Also it's better if disable_nonboot_cpus() returns an
error instead of panicking if something goes wrong, and
enable_nonboot_cpus() has no reason to panic(), because the CPUs may have
been enabled by the userland before it tries to take them online.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

On x86_64 machines with more than 2 GB of RAM there are large memory gaps
(with no corresponding kernel virtual addresses) and reserved memory
regions between areas of usable physical RAM.  Moreover, if CONFIG_FLATMEM
is set, they appear within the normal zone.  swsusp should not try to save
them, so the corresponding page structs have to be marked as 'nosave'.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add comments describing struct snapshot_handle and its members, change the
confusing name of its member 'page' to 'cur'.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean up some loops over pfns for each zone in snapshot.c: reduce the
number of additions to perform, rework detection of saveable pages and make
the code a bit less difficult to understand, hopefully.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Implement async reads for swsusp resuming.

Crufty old PIII testbox:
	15.7 MB/s -> 20.3 MB/s

Sony Vaio:
	14.6 MB/s -> 33.3 MB/s

I didn't implement the post-resume bio_set_pages_dirty().  I don't really
understand why resume needs to run set_page_dirty() against these pages.

It might be a worry that this code modifies PG_Uptodate, PG_Error and
PG_Locked against the image pages.  Can this possibly affect the resumed-into
kernel?  Hopefully not, if we're atomically restoring its mem_map?

Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jens Axboe <axboe@suse.de>
Cc: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add some instrumentation to the swsusp readin code to show what bandwidth
we're achieving.

Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Switch the swsusp writeout code from 4k-at-a-time to 4MB-at-a-time.

Crufty old PIII testbox:
	12.9 MB/s -> 20.9 MB/s

Sony Vaio:
	14.7 MB/s -> 26.5 MB/s

The implementation is crude.  A better one would use larger BIOs, but wouldn't
gain any performance.

The memcpys will be mostly pipelined with the IO and basically come for free.

The ENOMEM path has not been tested.  It should be.

Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>