The DEFAULT_RATE clksel_rate flag is essentially useless.  It was set
on some of the lowest divisors, which, when switching to a much
higher-rate parent, could have potentially resulted in rates that
exceeded the hardware specifications for downstream clocks in the
window between the clk_set_parent(), and a subsequent clk_set_rate().
It seems much safer to just remove the flag and always use the highest
available divisor (resulting in the lowest possible rate) after the
switch, and this patch does so.

Ideally, it would be best to first attempt to switch to a divisor that
matches the clock's rate with the previous parent, if at all possible.
But that is a project for some other day or some other person.  The
parent changing code is rarely used.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Writes to the PM_*GRPSEL registers should use _GRPSEL_ macros, not _EN_ macros,
to match the TRM and guard against inadvertent error.  This patch should
not cause any functional change.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>

Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them.  This makes the use of these
macros consistent.  It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them.  This makes the use
of these macros consistent.  It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

Fix all of the remaining OMAP2 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them.  This makes the use
of these macros consistent.  It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

There are three i2c buses on am3517, and each i2c bus has several devices
on it, so we can't name the i2c boardinfo structures with one of these
devices. In order to make it more readable, now rename these three boardinfo
structures based on i2c indexes.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Acked-By: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable Micrel KS8851 SPI network chip for OMAP4430
Signed-off-by: NAbraham Arce <x0066660@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM3517 don't have the register OMAP343X_CONTROL_PBIAS_LITE and the regulators
like "vmmc", so we set a noop "set_power" function for it.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There is two gpio for mmc use, one is for card detecting, another is
used for checking write protect. Intialize its pinmux in case the bootloader
doesn't set it.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The SDI Display subsystem needs access to the vdds_sdi supply
regulator. This is TWL4030's VAUX1 supply on RX-51.
Signed-off-by: NRoger Quadros <roger.quadros@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

EHCI port on UI card and LCD share two pins (GPIO 181 and 182) thus
they have to be mutually exclusive.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to tlv320aic3x codec driver require four supplies.
Implement this by connecting analogic supplies to TWL4030 VMMC2 and digital
supplies to TWL4030 VIO.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This makes possible to probe the audio codec and add another i2c2
components in the future.

Fix also indentation for the first omap_register_i2c_bus.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I believe the VMMC2 constraints must be the same than with VAUX3. Older
boards are using TWL4030 VMMC2 supply for internal MMC whereas newer are
using VAUX3 that has more limited constraints defined in this same file.

More over, the VMMC2 supply is used also for analog audio domain and the
miminum analog voltage of the TLV320AIC34 codec is 2.7 V.

To combine these two facts, the patch changes supply name to V28_A as the
newer boards register VMMC2_30 for VAUX3 and uses the same constraints than
VAUX3 since those constraints are ok for the TLV320AIC34.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some Overo add-on boards include a second ethernet port.  This patch
adds support for that second port.
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The emac driver currently uses Davinci clock names for the module and phy
clocks. Updated the omap3xxx_clks table to match the names
used by the Davinci emac driver.

Note that eventually the EMAC clocks should be renamed to be generic.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated patch description to match the patch]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Modified AM35xx EVM init sequence to handle EMAC
initialization.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define offsets for EMAC sub modules.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board specific hookup for TI HECC driver on
AM3517 EVM
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize multiplexed pins with correct mode.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Configuration for OMAP2430 should select ARCH_OMAP_OTG just like
it is done for OMAP2420
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform init code for OHCI USB on OMAP2430 SDP
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
[tony@atomide.com: Updated subject to mention the board name]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize isp1301 FS USB transceiver and
add I2C bus1 initialization code for OMAP2430 SDP
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds TLB preservation support to IOMMU module
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

Added the missing TLB valid entry setting for cam register
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

This patch provides the iommu support for OMAP4 co-processors.
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

This patch includes changes to omap3-iommu.c file to make it generic
for all OMAPs. Renamed omap3-iommu.c to omap-iommu.c

[Hiroshi DOYU: Remove unnecessary "iommu-y" in Makefile]
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.'  This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.

The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

We can remove this wakeup dependency since now, when
GPIO2-6 are enabled for IO-pad wakeup, PER domain is gauranteed
to be awake or be woken up to service.

The previous dependency did not handle all corner cases. Since there
was no sleep dependency between CORE and PER domains, if PER enters
RET and CORE is ON, PER will not be active for GPIO handling.
Signed-off-by: NMike Chan <mike@android.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

IO events can also come from GPIO modules, which reside in the PER domain.
It is possible for the PER to enter RET while CORE is still in ON.
If GPIO 2-6 are enabled for IO-pad wakeups, the PER domain will not
wakeup in this case, unless we enable it.
Signed-off-by: NMike Chan <mike@android.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This  patch enables the wakeup capabilities of ads7846 touchscreen driver.
ads7846 driver can now wakeup the system from suspend on OMAP3430 EVM
and SDP boards.

The earlier approach of enabling wakeup on the touchscreen GPIO pin during
board level mux init is removed. Instead the wakeup flag in
ads7846_platform_data is enabled. Based on the flag, the ads7846 driver
will do an enable_irq_wake which will eventually call into the OMAP GPIO
layer and will enable the wakeup capability on the GPIO pin.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

OMAP3530 TRM section 7.4.4.4.2 requires OFFOUTENABLE to be set (active low)
if wakeup capabilities are enabled on a pad. During OFF mode testing
on OMAP3530 EVM, it was observed that the device was not residing in
the OFF state. The device enters into the OFF state and immediately exits
from that state as if an IO wakeup event has occured. The issue was traced
down to the pad configuration of wkaeup enabled pad's.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Millisecond resolution is possible and there are use cases for it
(automatic testing).

Seconds-based interface is preserved for compatibility.
Signed-off-by: NAri Kauppi <Ext-Ari.Kauppi@nokia.com>
Reviewed-by: NPhil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

While handling PRCM IRQs, mask out interrupts that are not enabled in
PRM_IRQENABLE_MPU.  If these are not masked out, non-enabled
interrupts are caught, a WARN() is printed due to no 'handler' and the
events are cleared.  In addition to being noisy, this can also
interfere with independent polling of this register by SR/VP code.

This was noticed using SmartReflex transitions which cause the VPx_*
interrupts to be handled since they are set in PRM_IRQSTATUS_MPU even
but not enabled in PRM_IRQENABLE_MPU.
Acked-by: NMike Turquette <mturquette@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add V4L2 DSS driver support in device.c
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

These are currently non-muxable, so let's save some memory
and remove them. Otherwise we get the following warnings:

mux: Unknown ball offset 0x5e
mux: Unknown ball offset 0x60
mux: Unknown ball offset 0x62
...
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise we can get the following error:

error: variable 'tdo24m_mcspi_config' has initializer but incomplete type
...
Signed-off-by: NTony Lindgren <tony@atomide.com>

Zoom2 and 3 have UARTs only on the external debug board.
GPMC needs to be mapped early to use it for DEBUG_LL.

Additionally, 0xfb000000 overlaps with other areas, so
use 0xfa400000 for the virtual address instead.

Note that with the pending serial.c patches you need to
set console=ttyS0,115200n8 as it will be the only UART
mapped. To use DEBUG_LL, you need to pass also earlyprintk
in cmdline.

Cc: Allen Pais <allen.pais@ti.com>
Acked-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>