BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.

The BSC9131 SoC includes the following function and features:
    . Power Architecture subsystem including a e500 processor with 256-Kbyte
    shared L2 cache
    . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
    . The Multi Accelerator Platform Engine for Femto BaseStation Baseband
      Processing (MAPLE-B2F)
    . A multi-standard baseband algorithm accelerator for Channel
      Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
      UP/DL Channel processing, and CRC algorithms
    . Consists of accelerators for Convolution, Filtering, Turbo Encoding,
      Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
      Inversion operations
    . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
      with ECC, up to 400-MHz clock/800 MHz data rate
    . Dedicated security engine featuring trusted boot
    . DMA controller
    . OCNDMA with four bidirectional channels
    . Interfaces
    . Two triple-speed Gigabit Ethernet controllers featuring network
      acceleration including IEEE 1588. v2 hardware support and
      virtualization (eTSEC)
    . eTSEC 1 supports RGMII/RMII
    . eTSEC 2 supports RGMII
    . High-speed USB 2.0 host and device controller with ULPI interface
    . Enhanced secure digital (SD/MMC) host controller (eSDHC)
    . Antenna interface controller (AIC), supporting three industry standard
      JESD207/three custom ADI RF interfaces (two dual port and one single
      port) and three MAXIM's MaxPHY serial interfaces
    . ADI lanes support both full duplex FDD support and half duplex TDD
      support
    . Universal Subscriber Identity Module (USIM) interface that facilitates
      communication to SIM cards or Eurochip pre-paid phone cards
    . TDM with one TDM port
    . Two DUART, four eSPI, and two I2C controllers
    . Integrated Flash memory controller (IFC)
    . TDM with 256 channels
    . GPIO
    . Sixteen 32-bit timers

The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.

 BSC9131RDB Overview
 ----------------------
    BSC9131 SoC
    1Gbyte DDR3 (on board DDR)
    128Mbyte 2K page size NAND Flash
    256 Kbit M24256 I2C EEPROM
    128 Mbit SPI Flash memory
    USB-ULPI
    eTSEC1: Connected to RGMII PHY
    eTSEC2: Connected to RGMII PHY
    DUART interface: supports one UARTs up to 115200 bps for console display

 Linux runs on e500v2 core and access some DSP peripherals like AIC
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NAkhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NRajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This reverts commit 96cc017c.

The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This reference board dates back to 2004, and is largely a legacy
EOL product.  The MPC8560 is a pre e500v2 CPU.  The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.

Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.

Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable RapidIO and add rapidio and rmu nodes to dts.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove the "select PHYS_64BIT" from the Kconfig entry for the P1022DS,
so that large physical address support is a selectable option for non-CoreNet
reference boards.

The option is enabled in mpc85xx_[smp_]defconfig so that the default is
unchanged.  However, now it can be deselected.

The P1022DS had this option defined because the default device tree for
this board uses 36-bit addresses.  This had the side-effect of forcing
this option on for all boards that use mpc85xx_[smp_]defconfig.  Some
users may want to disable this feature to create an optimized configuration
for boards with <= 2GB of RAM.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

fsl_85xx_l2ctlr.o and fsl_85xx_cache_sram.o are built only
if CONFIG_FSL_85XX_CACHE_SRAM is defined. The driver that
qualifies and wants to make use of the CACHE SRAM's exported
API (i.e. a freescale net driver) should (be able to) select
this config option.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: NMartyn Welch <martyn.welch@ge.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The SERIAL_8250_EXTENDED option just enables access to other
less regularly used options, like SERIAL_8250_SHARE_IRQ.
Select it to get rid of this warning when selecting the child
option living underneath it.

  warning: (FSL_SOC_BOOKE && SERIAL_8250_RM9K) selects
  SERIAL_8250_SHARE_IRQ which has unmet direct dependencies
  (HAS_IOMEM && SERIAL_8250_EXTENDED)
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The driver for the Freescale P3060 QDS got added by commit 96cc017c
("[...] Add support for P3060QDS board"). Its Kconfig entry selects
MPC8xxx_GPIO. But at the time that driver got added MPC8xxx_GPIO was
already renamed to GPIO_MPC8XXX, by commit c68308dd ("gpio: move
mpc8xxx/512x gpio driver to drivers/gpio").

So make this driver select GPIO_MPC8XXX.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

P3060QDS Board Overview:
Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM
Ethernet:
  - 4x1G + 4x1G/2.5G Ethernet controllers
  - 2xRGMII + 1xMII, three VSC8641 PHYs on board
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C:  Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Remove wrong CONFIG_ prefix in Kconfig file.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.

During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
 - Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
 - Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1010RDB Overview
 -----------------
 1Gbyte DDR3 (on board DDR)
 32Mbyte 16bit NOR flash
 32Mbyte SLC NAND Flash
 256 Kbit M24256 I2C EEPROM
 128 Mbit SPI Flash memory
 I2C Board 128x8 bit memory
 SD/MMC connector to interface with the SD memory card
 2 SATA interface
         1 internal SATA connect to 2.5. 160G SATA2 HDD
         1 eSATA connector to rear panel
 USB 2.0
         x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
         x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
 eTSEC1: Connected to RGMII PHY VSC8641XKO
 eTSEC2: Connected to SGMII PHY VSC8221
 eTSEC3: Connected to SGMII PHY VSC8221 eCAN
 Two DB-9 female connectors for Field bus interface UART
 DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the ePAPR-compliant Freescale hypervisor (aka "Topaz") on
the Freescale P3041DS, P4080DS, and P5020DS reference boards.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture.  This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P5020DS is in the same family of boards as the P4080 DS and thus
shares the corenet_ds code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The new e5500 core is similar to the e500mc core but adds 64-bit
support.  We support running it in 32-bit mode as it is identical to the
e500mc.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P3041DS is in the same family of boards as the P4080DS and thus
shares the corenet_ds code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Introduce basic support for the Freescale P1022DS reference board, based on the
Freescale BSP for this board.  This patch excludes the DIU, SSI, and MMC/SD
drivers.  Only a 36-bit DTS is provided.

Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS.
This means enabling 64-bit physical address support, increasing the maximum
zone order to 12 (to allow the DIU driver to allocate large chunks), and
clean up the audio options to disable the deprecated OSS support.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Currently some MPC85xx and MPC86xx boards fail to build without
CONFIG_PCI:

arch/powerpc/platforms/fsl_uli1575.c: In function 'quirk_final_uli5249':
arch/powerpc/platforms/fsl_uli1575.c:234: error: implicit declaration of function 'pci_bus_for_each_resource'
arch/powerpc/platforms/fsl_uli1575.c:234: error: expected ';' before '{' token
cc1: warnings being treated as errors
arch/powerpc/platforms/fsl_uli1575.c:223: warning: unused variable 'dummy'
make[1]: *** [arch/powerpc/platforms/fsl_uli1575.o] Error 1

This patch fixes the issue by appending 'if PCI' condition when
selecting FSL_ULI1575 Kconfig symbol.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add basic support for the P4080 DS reference board.  None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Introduce new FSL_SOC_BOOKE Kconfig to handle both 85xx and QorIQ
based chips.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the P2020RDB reference board from Freescale.

Overview of P2020RDB platform
	- DDR
	  DDR2 1G
	- NOR Flash
	  16MByte
	- NAND Flash
	  32MByte
	- 3 Ethernet interfaces
	  1) etSEC1
		- RGMII
		- connected to a 5 port Vitesse Switch(VSC7385)
		- Switch is memory mapped through eLBC interface(CS#2)
		- IRQ1
	  2) etSEC2
		- SGMII
		- connected to VSC8221
		- IRQ2
	  3) etSEC3
		- RGMII
		- connected to VSC8641
		- IRQ3
	- 2 1X PCIe interfaces
	- SD/MMC ,USB
	- SPI EEPROM
	- Serial I2C EEPROM
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for X-ES single-board computers based on the Freescale
MPC85xx processors.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the platform-specific code for enabling SWIOTLB if needed on P2020DS,
MPC85xx DS, and MPC85xx MDS boards as they are capable of having >4G of
memory.

We determine if we need to enable swiotlb based on how much memory is in
the board and if it exceeds 4G or what we can map via PCI inbound
windows.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Supported are Ethernet, serial console, I2C, I2C-based RTC and
temperature sensors, NOR and NAND flash, PCI, USB, CAN and Lime
display controller.

The multiplexing of FPGA interrupts onto PowerPC interrupt lines is
supported through our own fpga_pic interrupt controller driver.

For example the SJA1000 controller is level low sensitive connected to
fpga_pic line 2 and is routed to the second (of three) irq lines to
the CPU:

    can@3,100 {
            compatible = "philips,sja1000";
            reg = <3 0x100 0x80>;
            interrupts = <2 2>;
            interrupts = <2 8 1>;   // number, type, routing
            interrupt-parent = <&fpga_pic>;
    };
Signed-off-by: NSergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: NYuri Tikhonov <yur@emcraft.com>
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDmitry Rakhchev <rda@emcraft.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Modify the Kconfig so that Freescale QUICC Engine (QE) support is a selectable
option, thereby allowing users to compile kernels without any QE support.

The drawback is that QE support is now disabled by default on platforms that
have a QE, and so a defconfig is needed to enable QE and QE devices (like
UCC GETH).  Fortunately, all the current relevant defconfigs do that already.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

With arch/ppc gone and all in kernel users of CONFIG_PPC_CPM_NEW_BINDING
fixed up we dont have need for the Kconfig option anymore.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Choosing PCI or not at config time is allowed on some
platforms via an if expression in arch/powerpc/Kconfig.
To add a new platform with PCI support selectable at
config time, you must change the if expression.  This
patch makes this easier by changing:
    bool "PCI support" if <long expression>
to
    bool "PCI support" if PPC_PCI_CHOICE
and adding select PPC_PCI_CHOICE to all the config nodes that
were previously in the PCI if expression.

Platforms with unconditional PCI support continue to
just select PCI in their config nodes.
Signed-off-by: NJohn Rigby <jrigby@freescale.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the MPC8536 process and MPC8536DS reference board.  The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.

The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPC85xx MDS board requires some board level tweaks of the PHYs that
either the eTSEC (gianfar) or UCC ethernet controllers are connected to.

Its possible to build the phylib as a module, however this breaks the
board level fix ups because phy_read and phy_write are not available
if we build as a module.

So we unconditionally select PHYLIB to ensure its built into the kernel
if we are building in MPC85xx MDS support.  This was determined to be
the easiest soultion even though it prevents the user from removing
PHYLIB support if they decide they don't want it.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The kconfig entry can go away once arch/ppc and references to the config in
drivers are removed.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.

The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* Allow multiple boards to be selected in a single build
* Removed Kconfig option '85xx' which existed only for compat with arch/ppc
* Added a multiplatform 85xx defconfig (mpc85xx_defconfig). This builds
  all 85xx boards except sbc8560 and stx_gp3 since these to boards have
  board specific ifdef in driver code that may break all other boards
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds the basic support for the Wind River SBC8548 board, implemented
as powerpc.  It closely follows the implementation of the MPC8548CDS.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>