The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since fcf98446 ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.

This fixes some P2P connection setup issues.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Further testing proved that multi-channel AP+STA
on QCA6174 with RM.2.0-00088 should have powersave
force-disabled to avoid beacon misses/skipping on
either side which in turn could disrupt
communication.

Since AP never has arvif->ps don't even bother
checking it. Other combinations may be broken as
well so disallow powersave with multivif outright
unless firmware advertises otherwise.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mac80211 already does provide complete IEs for
Probe Requests for hw scan and ath10k firmware was
appending duplicate Supported Rates IEs
unnecessarily.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In commit 418ca599 ("ath10k: Make target cpu address to
CE address conversion chip specific") mask 0x7fff is added
by mistake instead of 0x7ff. Fix this regression.

Fixes: 418ca599 ("ath10k: Make target cpu address to CE address conversion chip specific")
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

commit a521ee98 ("ath10k: Add new reg_address/mask to hw register
table") broke QCA61x4 support by providing wrong
fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028.

User experience was a failing boot up sequence (crashing device during
initialization):

[  181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[  181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[  181.688886] ath10k_pci 0000:02:00.0: device has crashed during init
[  181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70
[  181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70
[  181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70

Fix it by updating the address with correct value.

Fixes: a521ee98 ("ath10k: Add new reg_address/mask to hw register table")
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Pre qca99X0 chipsets follows the model where dynamically allocate
memory for frag desc on getting new skb for TX. But, this is not
going to be the case in qca99X0. It expects frag desc memory to be
allocated at boot time and let the driver to reuse allocated memory
after every TX completion. So there won't be any dynamic frag memory
memory allocation in qca99X0 during data transmission.

qca99X0 hardware doesn't need fragment desc address to be programmed
in msdu descriptor for every data transaction. It needs to know only
starting address of fragment descriptor at the time of the boot.
During data transmission, qca99X0 hardware can retrieve corresponding
frag addr by adding programmed frag desc base addr + msdu id.

Allocate continuous fragment descriptor memory (same size as number of
descriptor) at the time of target initialization and configure allocated
dma address to the target via HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG.

How this is allocated continuous memory is going to be used is not
covered in this patch. It just allocates memory and hand over to firmware.
If we don't do it at init time, qca99X0 will stall when firmware tries
to do TX.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 fw supports upto 4 spatial stream. Limit max spatial
stream to 4 for 10.4 firmware and to 3 for non 10.4 firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 fw supports upto 16 interface in ap mode and 1 interface
in station mode, overall total interfaces supported are 16
interfaces. Populate this limit in wiphy->iface_combinations.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New htt event table is added for 10.4 firmware. Following new htt
events are available only 10.4. adding this to generic htt event
table,
	HTT_T2H_MSG_TYPE_EN_STATS,
	HTT_T2H_MSG_TYPE_TX_FETCH_IND,
	HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
	HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Existing non 10.4 firmware scan related events and commands are
matching with 10.4 firmware (except chan info event). Link general
start scan,stop scan, scan channel list configuration functions
to 10.4 wmi function table and add a new handler to parse 10.4
specific chan info event.

10.4 firmware has extra scan completion reason
WMI_SCAN_REASON_INTERNAL_FAILURE and new scan event
WMI_SCAN_EVENT_FOREIGN_CHANNEL_EXIT compared to previous firmware
versions. These things are added in respective enum.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Most of existing vdev and peer related functions (vdev create,
vdev delete, vdev start, peer create, peer delete, peer flush, etc)
are reusable for 10.4 firmware. Link those general vdev and peer
functions to 10.4 wmi function table.

Existing general pktlog enable/disable, dbglog configuration functions
are reusable for 10.4 and add them also in wmi function table.

Also handle few wmi events (sevice rdy, echo, dbg msg, tbtt offset
update, dbg print) in ath10k_wmi_10_4_op_rx(). wow event is not
applicable in 10.4 firmware, have it under not implemented print.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware swba event payload has space to accommodate upto
512 client traffic indication info & one p2p noa descriptor.
It's is not matching with exiting swba event format defined for
non 10.4 firmware. Non 10.4 firmware swba event format is designed
to support only upto only 128 client and four p2p notice of absence
descriptor.

following changes are done in this patch to enable ath10k to handle
10.4 firmware swba event,

 - link generic ath10k_wmi_event_host_swba() to handle 10.4 swba
   event in 10.4 wmi rx handler.

 - add 10.4 specific swba event structure wmi_10_4_host_swba_event.

 - new function ath10k_wmi_10_4_op_pull_swba_ev() to parse
   10.4 swba event.

 - increase tim_bitmap[] size in ath10k_vif to 64 to hold 512 station
   power save state.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Due to 512 client support in 10.4 firmware, size of tim ie is going
to be slightly higher than non 10.4 firmware. So, size of tim_bitmap
what is carried in swba event from 10.4 firmware is bit higher.

The only bottle neck to reuse existing swba handler
ath10k_wmi_event_host_swba() for 10.4 is that code designed to deal
with fixed size tim bitmap(ie, tim_info[].tim_bitmap in wmi_swba_ev_arg).
This patch removes such size limitation and makes it more suitable
to handle swba event which has different size tim bitmap.

All existing swba event parsing functions are changed to adapt this
change. Actual support to handle 10.4 swba event is added in next patch.
Only preparation is made in this patch.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

privacy settings might change while AP is running.
Inside wil_cfg80211_change_beacon(), detect change
in privacy settings and handle it by stopping and
re-starting the AP.
Firmware cannot handle on-the-fly privacy settings
change and so AP restart is required.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In the PRI detector, after the current radar pulse
has been checked agains existing PRI sequences, it
is considered as part of a new potential sequence.

Previously, the condition to accept a new sequence
was to have at least the same number of pulses as
the longest matching sequence. This was wrong,
since it led to duplicates of PRI sequences.

This patch changes the acceptance criteria for new
potential sequences from 'at least' to 'more than'
the longest existing.

Detection performance remains unaffected, while
the number of PRI sequences accounted at runtime
(and with it CPU load) is reduced by up to 50%.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Reuse existing function ath10k_wmi_op_pull_rdy_ev()
to parse WMI_10_4_READY_EVENTID and handle the same
event in ath10k_wmi_10_4_op_rx().
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware supports upto 512 clients when qcache feature is enabled.
Make adjustment on default max peer count, active peers, number of tid in
such case to meet qcache requirement. 10.4 fw has extra unit info flag
NUM_UNITS_IS_NUM_ACTIVE_PEERS which is also handled in this patch.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware wmi mgmt rx event format differs from non 10.4
firmware and changing existing wmi mgmt rx event parsing function
ath10k_wmi_op_pull_mgmt_rx_ev() for 10.4 would add more complex.

This patch adds new function to receive any wmi rx event from
10.4 firmware and also introduce new function to parse wmi mgmt
rx event.

In addition, fw main branch service rdy event parsing function
is linked in wmi ops table.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Define 10.4 wmi init command structure and introduce new function
ath10k_wmi_10_4_op_gen_init() to fill default values for each field
which goes as part of wmi init cmd to 10.4 firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Include 10.4 firmware wmi pdev cmd id and prepare wmi vdev map
table wmi_10_4_pdev_param_map and update non 10.4 firmware
pdev cmd map table with newly added vdev cmd id specifically for
10.4 firmware as unsupported.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Include 10.4 firmware wmi vdev cmd id and make up wmi vdev map
table wmi_10_4_vdev_param_map and also update non 10.4 firmware
vdev cmd map table with newly added vdev cmd id specifically for
10.4 firmware as unsupported.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In fact, explicit assigned to ZERO for unsupported wmi commands
are not really needed. Global static variable will have ZERO by
default. However, just for better readability setting all wmi cmds
in non 10.4 firmware wmi mapping table as unsupported for wmi cmd
which are exclusively available only in 10.4 firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware wmi cmd and event id values are not exactly aligned
with previous firmware versions (main, 10.x, 10.2, etc). Add new
enum to define wmi cmd & event definitions for 10.4 firmware and
prepare wmi_10_4_cmd_map based on 10.4 firmware wmi cmd definitions.

wmi_cmd_map is extended to accommodate new wmi commands which are
exclusively available in 10.4 firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Include new enum to define wmi service bitmap definitions for
10.4 firmware and a function wmi_10_4_svc_map() to remap 10.4
firmware wmi service bitmap definitions to ath10k generic wmi
services.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca99X0 chip uses firmware version 10.4. Define a new macro
ATH10K_FW_WMI_OP_VERSION_10_4 for 10.4 firmware and include
in switch cases where ATH10K_FW_WMI_OP_VERSION_* is used
to avoid compilation error.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

BMI parameter value to execute downloaded otp binary
is different for QCA99X0. Have a member in hw_params
to hold hw specific BMI param.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Code swap is a mechanism to use host memory to store
some fw binary code segment. Ath10k host driver allocates
and loads the code swap binary into the host memory and
configures the target with the host allocated memory
information at the address taken from code swap binary.
This patch adds code swap support for firmware binary.
Code swap binary for firmware bin is available in
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There is more than 1 sec delay in getting response from target
through BMI in QCA99X0. Increase the BMI communication timeout
to 2*HZ to fix BMI failures.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 uses two new copy engine src desc flags for interrupt
indication. Bit_2 is to mark if host interrupt is disabled after
processing the current desc and bit_3 is to mark if target interrupt
is diabled after the processing of current descriptor.
CE_DESC_FLAGS_META_DATA_MASK and CE_DESC_FLAGS_META_DATA_LSB are based
on the target type.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 supports only cold reset. Also, made
ath10k_pci_irq_msi_fw_mask() and ath10k_pci_irq_msi_fw_unmask()
non-99X0 specific till we get proper register configuration
to mask/unmask irq/MSI.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make the helper converting target virtual address space to CE address
space a target type specific to support QCA99X0. Also make this as
function instead of macro.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 supports upto 12 Copy engines. Host and target
CE configuration table is updated to support new copy engine
pipes. This also fixes the assumption of diagnostic CE by making
CE_7 as the one instead of CE_COUNT - 1.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to prepare the driver for QCA99X0 chip support.
This commit adds hw_params, hw register table and hw_values
table for QCA99X0 chip. Please note this is only a partial patch adding
support for QCA99X0, so the device id is not yet added to pci device
table.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add more register address and mask which can be different
for newer chip to hw_reg table.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to prepare ath10k to support newer chip set.
Values like CE_COUNT, MSI_ASSIGN_CE_MAX and
RTC_STATE_V_ON can be different for different
chips.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

wait_event_timeout(), introduced in 'commit 5e3dd157 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is == 0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

wait_event_timeout(), introduced in 'commit 5e3dd157 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is ==0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Just found this during code review.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was possible to force an out of bounds MMIO
read/write via debugfs. E.g. on QCA988X this could
be triggered with:

 echo 0x2080e0 | tee /sys/kernel/debug/ieee80211/*/ath10k/reg_addr
 cat /sys/kernel/debug/ieee80211/*/ath10k/reg_value

 BUG: unable to handle kernel paging request at ffffc90001e080e0
 IP: [<ffffffff8135c860>] ioread32+0x40/0x50
 ...
 Call Trace:
  [<ffffffffa00d0c7f>] ? ath10k_pci_read32+0x4f/0x70 [ath10k_pci]
  [<ffffffffa0080f50>] ath10k_reg_value_read+0x90/0xf0 [ath10k_core]
  [<ffffffff8115c2c1>] ? handle_mm_fault+0xa91/0x1050
  [<ffffffff81189758>] __vfs_read+0x28/0xe0
  [<ffffffff812e4694>] ? security_file_permission+0x84/0xa0
  [<ffffffff81189ce3>] ? rw_verify_area+0x53/0x100
  [<ffffffff81189e1a>] vfs_read+0x8a/0x140
  [<ffffffff8118acb9>] SyS_read+0x49/0xb0
  [<ffffffff8104e39c>] ? trace_do_page_fault+0x3c/0xc0
  [<ffffffff8196596e>] system_call_fastpath+0x12/0x71
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable VHT support for IBSS, while mac80211/cfg80211 and
wpa_supplicant already support this.

In my test env, qca988x 2x2 I get:

(udp) ath10k-1 >>>> ath10k-2 (server) -  speed: 419 Mbits/sec
(tcp) ath10k-1 >>>> ath10k-2 (server) -  speed: 404 Mbits/sec

During tests I used wpa_supplicant (latest git version), which
already support IBSS VHT, and choose highest available BW. Also tested with
qca6174.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>