Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Sky2 driver will oops referencing bad memory if used on
a dual port card.  The problem is accessing past end of
MIB counter space.

Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The hardware has additional error trap interrupt bits.  I have never seen
them trigger, but if they do, it looks like this might be useful.
Signed-off-by: NStephen Hemminger <shemminger@osdl.rog>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add MSI support to sky2 driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Redo the interupt handling of sky2 driver based on the IRQ mangement
documentation. All interrupts are handled by the device0 NAPI poll
routine.

Don't need to adjust interrupt mask in IRQ context, done only when
changing device under RTNL. Therefore don't need hwlock anymore.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove wake on lan support for now. It doesn't work right, and I
don't have a machine with working suspend/resume to test or fix it.
It will be re-enabled later.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Yukon EC/rev0 (A1) chipset requires a bunch of workarounds. I copied these
from sk98lin.  But since they never got tested and add more cruft to the code;
any attempt at using driver as is on this version will probably fail.

It looks like this was a early engineering sample chip revision, if it ever shows
up on a real system. Produce an error message.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.

In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to avoid race in updating IRQ mask.  This can probably be replaced
smarter use of the interrupt control registers (if/when chipset
docs are available).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

To avoid problems with PCI config access without ACPI (or busted ACPI tables),
use the device's window into PCI config space.

I know this probably will upset the purists, but I would rather have users
than ACPI testers. It also generates less code.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Add more complete setup code for Yukon EC_U chipset.
Based on matching code in 8.31 code in SysKonnect vendor driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

This hardware supports Message Signaled interrupts.
When setting up, use software interrupt to check for bad hardware.

Signed-off-by: Stephen Hemminger <shemminger @osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

There were bugs in mmconfig access to PCI space, up to and
include 2.6.16-rc1. These prevented the sky2 driver from being
able to clear PCI express errors.

This patch makes the driver check (during probe), for errors
in PCI config access and fail.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Split Tx and Rx ring into two different data structures.
Tx needs the next value (to handle partial status), and
Rx always needs the mapaddr (to handle resubmitting same buffer).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Don't need to keep track of mapping length in ring structure
because we can get the same info from other info.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Do phy processing in a work queue rather than a tasklet.
This means we can let bottom halves run.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

It is a useful optimization to rearrange the structure
slightly to align receive and transmit portions.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Eliminate special case tuning for PCI-Express. This code
causes receive hangs and doesn't help performance much anyway.
Signed-off-by: NStephen Hemminger <shemmnger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Use byteorder annotation for hardware structures
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Add support for Yukon-EC Ultra chip as implemented in SysKonnect's
driver version 8.26.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cosmetic cleanup's: mostly spelling fixes etc.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The sky2 driver has a lot of register definitions, that were
copied over from the skge driver, for areas that don't exist
on the Yukon2.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Add better power management, and power down the chip on device removal
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Use the hardware to do VLAN.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The Yukon2 chip FIFO has a problem recovering from a pause frame
if the receive buffer is not aligned. The workaround is to just
leave receive buffer at original alignment, which will make IP
header unaligned. Rework receive logic for clarity.

Need to ignore receive overrun interrupts (or mac hangs).

These fixes make the sky2 driver generally usable.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Here is revised patch against netdev sky2 branch.
It includes whitespace fixes, all the changes from the previous
review as well as some optimizations and timing fixes to
solve some of the hangs.

The stall problem is better but not perfect. It appears that
under stress the chip can't keep up with the bus
and sends a pause frame, then hangs. This version is for
testing, and hopefully other eyes might see the root
cause of the problem.

I don't want to reinvent the ugly watchdog code in the syskonnect
version of sk98lin.  If you read it you will see, the original
driver writer and the hardware developer obviously didn't
understand each other.

Dual port support is included, but not tested yet. It did
require small change to NAPI since both ports share same
IRQ.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

New driver for the Marvell Yukon2 Gigabit Ethernet chipset.
This driver is based on the skge driver, but using the logic
from the SysKonnect version of the sk98lin driver.
It should support all the Yukon2 chipsets that are available
in many current Intel and AMD motherboards.

The driver does support ethtool, tx and rx checksum, and
tcp segmentation offload.  But it has only been tested for
a short while and is known to stop receiving under heavy load.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cleanup the code that handles fibre vs copper detection.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

 drivers/net/skge.c |   26 ++++++++++++--------------
 drivers/net/skge.h |   11 ++---------
 2 files changed, 14 insertions(+), 23 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Some versions of the Marvell yukon generate bogus sensor warning interrupts.
The driver would flood log with these messages.  Handle this situation
cleanly by masking away at boot time.

Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

 drivers/net/skge.c |   24 ++++++++++--------------
 drivers/net/skge.h |    8 ++++++--
 2 files changed, 16 insertions(+), 16 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Minor whitespace cleanups.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Missing PCI_REV_DESC define.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimize the receive buffer management code to replenish the
buffers immediately (like tg3).
Signed-off-by: NStephen Hemmminger <shemminger@osdl.org>

Need to handle receive and transmit packet arbiter timeouts.
Transmit arbiter timeouts happens when Gigabit sends to 100Mbit port
on same switch and pause occurs.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Cleanup messages (for debug) about PHY interrrupts, because when
user can't get driver working that is often the problem.
Use a consistent way of enabling interrupts by port.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Rewrite the code for handling the Broadcom PHY to something that
works. Remove link polling because Broadcom and Yukon don't need it.
When I wrote initial code, didn't have a genesis chipset based
board to test, so it was a non-working guess.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>