In particular, blend_setup() should not overwrite the other crtc's mixer
settings.  Also, the encoder needs to be able to specify the mixer-id
explicitly, since both LVDS and DTV use 'INTF_LVDC_DTV', so we cannot
guess the mixer-id from the interface.
Signed-off-by: NRob Clark <robdclark@gmail.com>

In particular, pick up the definitions for a handful of LVDS related
registers.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Downstream kernel holds this clk via a fake-parent relationship.
Upstream clock framework requires that we hold it explicitly.
Signed-off-by: NRob Clark <robdclark@gmail.com>

The hw cursor is relatively adept at triggering underflows, which
manifest as a "blue flash" (since blue is configured as the underflow
color).  Juggle a few things around to tighten up the timing for setting
cursor registers in DONE irq.

And most importantly, don't ever disable the hw cursor.  Instead flip it
to a blank/empty cursor.  This seems far more reliable, as even simply
clearing the cursor-enable bit (with no other updates in previous/
following frames) can in some cases cause underflow.

v1: original
v2: add missing locking spotted by Micah

Cc: Micah Richert <richert@braincorporation.com>
Signed-off-by: NRob Clark <robdclark@gmail.com>

We'll want basically the same thing for mdp5, so refactor it out so it
can be shared.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NRob Clark <robdclark@gmail.com>

This can be shared between mdp4 and mdp5.  Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: NRob Clark <robdclark@gmail.com>

resync to latest envytools db, add mdp5 registers
Signed-off-by: NRob Clark <robdclark@gmail.com>

There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: NRob Clark <robdclark@gmail.com>

There were a few potential problems with the original page_flip/vblank
code in mdp4_crtc.

1) We need vblank irq for a couple things, both completing flips and
   updating cursor.  We need to keep track of what work is pending so
   that (for example) a cursor update while we are still waiting for
   pageflip_cb (ie. pageflip requested from userspace, but still
   waiting for rendering to complete) would not prematurely trigger
   event to userspace.

2) A preclose -> pageflip-cancel should not cancel a pageflip that
   was requested on a different file (ie. non-master closing should
   not cancel a pending pageflip).

With these fixes, we no longer have problems w/ cursor not updating and
with occasional hangs with userspace waiting for a pageflip that had
been cancelled (launching XBMC from gnome-shell overview mode was a good
way to trigger this, but now works reliably).
Signed-off-by: NRob Clark <robdclark@gmail.com>

Enable using VG1 and VG2 for planes.  Currently YUV/CSC or scaling is
not enabled, but ARGB and xRGB blending is.
Signed-off-by: NRob Clark <robdclark@gmail.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>

resync to latest envytools db, fixes a typo: s/mpd4/mdp4/
Signed-off-by: NRob Clark <robdclark@gmail.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>

The snapdragon chips have multiple different display controllers,
depending on which chip variant/version.  (As far as I can tell, current
devices have either MDP3 or MDP4, and upcoming devices have MDSS.)  And
then external to the display controller are HDMI, DSI, etc. blocks which
may be shared across devices which have different display controller
blocks.

To more easily add support for different display controller blocks, the
display controller specific bits are split out into a "kms" module,
which provides the kms plane/crtc/encoder objects.

The external HDMI, DSI, etc. blocks are part encoder, and part connector
currently.  But I think I will pull in the drm_bridge patches from
chromeos tree, and split them into a bridge+connector, with the
registers that need to be set in modeset handled by the bridge.  This
would remove the 'msm_connector' base class.  But some things need to be
double checked to make sure I could get the correct ON/OFF sequencing..

This patch adds support for mdp4 crtc (including hw cursor), dtv encoder
(part of MDP4 block), and hdmi.
Signed-off-by: NRob Clark <robdclark@gmail.com>