Add CONFIG_OF guard and use of_match_ptr macro.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.

This patch replaces the usage of these string functions in the smc911x
accessors with io{read,write}{8,16,32}_rep calls instead.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: netdev@vger.kernel.org
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.

With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip ready check added by the commit 3ac3546e [Always wait for
the chip to be ready] does not work when the register read/write
is word swapped. This check has been added before the WORD_SWAP
register is programmed, so we need to check for swapped register
value as well.

Bit 16 is marked as RESERVED in SMSC datasheet, Steve Glendinning
<steve@shawell.net> checked with SMSC and wrote:

  The chip architects have concluded we should be reading PMT_CTRL
  until we see any of bits 0, 8, 16 or 24 set.  Then we should read
  BYTE_TEST to check the byte order is correct (as we already do).

  The rationale behind this is that some of the chip variants have
  word order swapping features too, so the READY bit could actually
  be in any of the 4 possible locations.  The architects have confirmed
  that if any of these 4 positions is set the chip is ready.  The other
  3 locations will either never be set or can only go high after READY
  does (so also indicate the device is ready).

This change will check for the READY bit at the 16th position. We do
not check the other two cases (bit 8 and 24) since the driver does not
support byte-swapped register read/write.
Signed-off-by: NKamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We encapsulate enbale irq functionality in a function call.
As on probe the interrupts will be disabled twice, we delete
one.
Signed-off-by: NMatthias Brugger <mbrugger@iseebcn.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current failure paths attempt to free resources which we failed to request
and disable resources which we failed to enable ones. This leads to kernel
oops/panic. This patch does some simple re-ordering to prevent this from
happening.

Cc: netdev@vger.kernel.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refrain from attempting to free an interrupt line if the request
fails and hence, there is no IRQ to free.

CC: netdev@vger.kernel.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.

This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMSC LAN generation 4 chips integrate an IEEE 802.3 ethernet physical layer.
The PHY driver for this integrated chip enable an energy detect power-down mode.
When the PHY is in a power-down mode, it prevents the MAC portion chip to be
software reseted.

That means that if we compile the kernel with the configuration option SMSC_PHY
enabled and try to bring the network interface up without an cable plug-ed the
PHY will be in a low power mode and the software reset will fail returning -EIO
to user-space:

root@igep00x0:~# ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error

This patch disable the energy detect power-down mode before trying to software
reset the LAN chip and re-enables after it was reseted successfully.
Signed-off-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some basic regulator support for the power pins, as needed
by the ST-Ericsson Snowball platform that powers up the SMSC911
chip using an external regulator.

Platforms that use regulators and the smsc911x and have no defined
regulator for the smsc911x and claim complete regulator
constraints with no dummy regulators will need to provide it, for
example using a fixed voltage regulator. It appears that this may
affect (apart from Ux500 Snowball) possibly these archs/machines
that from some grep:s appear to define both CONFIG_SMSC911X and
CONFIG_REGULATOR:

- ARM Freescale mx3 and OMAP 2 plus, Raumfeld machines
- Blackfin
- Super-H

Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRobert Marklund <robert.marklund@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wait for the chip to be ready before any access to it. On the
Snowball platform we need to enable an external regulator before
the chip comes online, and then it happens that the device is
not yet ready at probe time, so let's wait for it.
Signed-off-by: NRobert Marklund <robert.marklund@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SMSC911X_USE_16BIT needs to be set when using 16-bit register
access.  However, currently no flag is set if the device tree
doesn't specify 32-bit access, resulting in a BUG() and a non-
working driver when 16-bit register access is configured for
smsc911x in the DT.

This patch should set the SMSC911X_USE_16BIT flag in a manner
consistent with the documented DT bindings.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the SMC (SMSC) drivers into drivers/net/ethernet/smsc/ and the
necessary Kconfig and Makefile changes.  Also did some cleanup
of NET_VENDOR_SMC Kconfig tag for the 8390 based drivers.

CC: Nicolas Pitre <nico@fluxnic.net>
CC: Donald Becker <becker@scyld.com>
CC: Erik Stahlman <erik@vt.edu>
CC: Dustin McIntire <dustin@sensoria.com>
CC: Steve Glendinning <steve.glendinning@smsc.com>
CC: David Hinds <dahinds@users.sourceforge.net>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It adds device tree probe support for smsc911x driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables software (and phy device) transmit time stamping.
Compile tested only.

Cc: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a revised patch that permits a shifted access to the
LAN9221 registers.  More specifically:

 It adds a shift parameter in the platform_data.
 It introduces an ops in smsc911x_data.
 A choice of access function to use at run-time.
 Four new shifted access function.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When SMSC911X_SAVE_MAC_ADDRESS flag is enabled the driver calls
smsc911x_mac_read and smsc911x_mac_read function without acquiring mac_lock
spinlock

This patch fixes following warning

smsc911x: Driver version 2008-10-21.
------------[ cut here ]------------
WARNING: at drivers/net/smsc911x.c:261 smsc911x_mac_read+0x24/0x220()
Modules linked in:
[<c0060858>] (unwind_backtrace+0x0/0xe0) from [<c009322c>] (warn_slowpath_common+0x4c/0x64)
[<c009322c>] (warn_slowpath_common+0x4c/0x64) from [<c009325c>] (warn_slowpath_null+0x18/0x1c)
[<c009325c>] (warn_slowpath_null+0x18/0x1c) from [<c0324bec>] (smsc911x_mac_read+0x24/0x220)
[<c0324bec>] (smsc911x_mac_read+0x24/0x220) from [<c0434788>] (smsc911x_read_mac_address+0x18/0x6c)
[<c0434788>] (smsc911x_read_mac_address+0x18/0x6c) from [<c0434c74>] (smsc911x_drv_probe+0x498/0x1788)
[<c0434c74>] (smsc911x_drv_probe+0x498/0x1788) from [<c02d3e54>] (platform_drv_probe+0x14/0x18)
[<c02d3e54>] (platform_drv_probe+0x14/0x18) from [<c02d2d60>] (driver_probe_device+0xc8/0x184)
[<c02d2d60>] (driver_probe_device+0xc8/0x184) from [<c02d2e84>] (__driver_attach+0x68/0x8c)
[<c02d2e84>] (__driver_attach+0x68/0x8c) from [<c02d1fc8>] (bus_for_each_dev+0x48/0x74)
[<c02d1fc8>] (bus_for_each_dev+0x48/0x74) from [<c02d2660>] (bus_add_driver+0x9c/0x228)
[<c02d2660>] (bus_add_driver+0x9c/0x228) from [<c02d3598>] (driver_register+0xa0/0x124)
[<c02d3598>] (driver_register+0xa0/0x124) from [<c0050668>] (do_one_initcall+0x94/0x168)
[<c0050668>] (do_one_initcall+0x94/0x168) from [<c0008984>] (kernel_init+0xa0/0x154)
[<c0008984>] (kernel_init+0xa0/0x154) from [<c005afac>] (kernel_thread_exit+0x0/0x8)
---[ end trace 2c931a35b7885770 ]---
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Use the more common/verbose logging styles.

Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove smsc911x prefixes from format strings.
Rename SMSC_WARNING to SMSC_WARN.
Remove DPRINTK macro.
Use netif_<level> in SMSC_<level> macros.
Convert NETIF_MSG_<foo> uses to lower case.
Add no_printk verification in non-debug uses.
Add pdata to SMSC_<level> uses to avoid hidden variable uses.
Convert printks to netdev_<level> as appropriate.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes build error when SMSC_TRACE() used.
Signed-off-by: NJeongtae Park <jtp.park@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The smsc911x driver would drop frames longer than 1518 bytes, which is a
problem for networks with VLAN tagging. The VLAN1 tag register is used
to increase the legal frame size to 1522 when a VLAN tag is identified.
Signed-off-by: NGöran Weinholt <weinholt@csbnet.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for SMSC911X and SMC911X for the ASB2364 unit.
Signed-off-by: NAkira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: NKiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: steve.glendinning@smsc.com
cc: netdev@vger.kernel.org

This enables auto loading for the smsc911x ethernet driver.
Signed-off-by: NVincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fresh skbs have ip_summed set to CHECKSUM_NONE (0)

We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.

Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.

Change most occurrences of :

skb->ip_summed = CHECKSUM_NONE;

by :

skb_checksum_none_assert(skb);
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On SMP systems, the SMSC911x registers may be accessed by multiple CPUs
and this seems to put the chip in an inconsistent state. The patch adds
spinlocks to the smsc911x_reg_read, smsc911x_reg_write,
smsc911x_rx_readfifo and smsc911x_tx_writefifo functions.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.

Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

[Ss]ytem => [Ss]ystem
udpate => update
paramters => parameters
orginal => original
Signed-off-by: NThomas Weber <swirl@gmx.li>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

also removed unnecessary checks
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>