The old ifdef CONFIG_BRCMFISCAN looks wrong to me and it makes more
sense when CONFIG_BRCMISCAN is used.
This patch was just compile tested by me, but not runtime tested.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added Atheros AR3011 internal bluetooth device found in Sony VAIO VPCEH to the
devices list.
Before this, the bluetooth module was identified as an Foxconn / Hai bluetooth
device [0489:e027], now it claims to be an AtherosAR3011 Bluetooth
[0cf3:3005].

T:  Bus=01 Lev=02 Prnt=02 Port=04 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e027 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NMarcos Chaparro <marcos@mrkindustries.com.ar>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

To let mac80211 clean up any TX information when
a frame is dropped, use ieee80211_free_txskb().
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The RX replenish code doesn't handle DMA mapping failures,
which will cause issues if there actually is a failure. This
was reported by Shuah Khan who found a DMA mapping framework
warning ("device driver failed to check map error").

Cc: stable@vger.kernel.org
Reported-by: NShuah Khan <shuah.khan@hp.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The ath9k xmit functions for AMPDUs can send frames as non-aggregate in case
only one frame is currently available. The client will then answer using a
normal Ack instead of a BlockAck. This acknowledgement has no TID stored and
therefore the hardware is not able to provide us the corresponding TID.

The TID set by the hardware in the tx status descriptor has to be seen as
undefined and not as a valid TID value for normal acknowledgements. Doing
otherwise results in a massive amount of retransmissions and stalls of
connections.

Users may experience low bandwidth and complete connection stalls in
environments with transfers using multiple TIDs.

This regression was introduced in b11b160d
("ath9k: validate the TID in the tx status information").
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Cc: stable@vger.kernel.org
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some hardware has correct (!= 0xff) value of tssi_bounds[4] in the
EEPROM, but step is equal to 0xff. This results on ridiculous delta
calculations and completely broke TX power settings.
Reported-and-tested-by: NPavel Lucik <pavel.lucik@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bf->bf_next is only while buffers are chained as part of an A-MPDU
in the tx queue. When a tid queue is flushed (e.g. on tearing down
an aggregation session), frames can be enqueued again as normal
transmission, without bf_next being cleared. This can lead to the
old pointer being dereferenced again later.

This patch might fix crashes and "Failed to stop TX DMA!" messages.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When b43 fails to find firmware when loaded, a subsequent unload will
oops due to calling ieee80211_unregister_hw() when the corresponding
register call was never made.

Commit 2d838bb6 fixed the same problem
for b43legacy.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NMarkus Kanet <dvmailing@gmx.eu>
Cc: Stable <stable@vger.kernel.org> [V3.3.0+ (the patch will need to be refactored)]
Cc: Markus Kanet <dvmailing@gmx.eu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

De-reference and deallocate scan state on failure.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NPaul Stewart <pstew@chromium.org>
Tested-by: NPaul Stewart <pstew@chromium.org>
Reviewed-by: NRyan Cairns <rtc@chromium.org>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previous patch "mwifiex: return -EBUSY if scan request cannot.."
corrected regular scan request only. There is another case for
specific scan that needs the same handling.

Also, removed !req_ssid check as it has already been validated
by caller.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NPaul Stewart <pstew@chromium.org>
Reviewed-by: NRyan Cairns <rtc@chromium.org>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a samtch warnings catched by Fengguang's 0-DAY system:
+ drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:3572 brcmf_cfg80211_sched_scan_start() error: we previously assumed 'request' could be null (see line 3571)

Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit a240dc7b.

This commit is reducing tx power by at least 10 db on some devices,
e.g. the Buffalo WZR-HP-G450H.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Roger says, Ubiquiti produce 2 versions of their WiFiStation USB adapter.  One
has an internal antenna, the other has an external antenna and
name suffix EXT.  They have separate USB ids and in distribution
openSUSE 12.2 (kernel 3.4.6), file /usr/share/usb.ids shows:

  0cf3  Atheros Communications, Inc.
       ...
       b002  Ubiquiti WiFiStation 802.11n [Atheros AR9271]
       b003  Ubiquiti WiFiStationEXT 802.11n [Atheros AR9271]

Add b002 Ubiquiti WiFiStation in the PID/VID list.
Reported-by: NRoger Price <ath9k@rogerprice.org>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes warnings like below happened on resume:

WARNING: at net/mac80211/driver-ops.h:12 check_sdata_in_driver+0x32/0x34()

Problem is that in __ieee80211_susped() we remove sdata (i.e wlan0
interface) and then during resume we call usb_unbind_interface() ->
ieee80211_unregister_hw() with sdata removed.

Patch fixes problem by adding .reset_resume calback, hence we do not
unbind usb device on resume. This callback can be the same as normal
.resume callback, sice we do all needed initalization during interface
start, which is performed on resume [ ieee80211_resume() ->
ieee80211_reconfig() -> rt2x00mac_start() -> rt2x00lib_start ].

Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=48041Reported-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Reported-and-tested-by: NStephen Boyd <bebarino@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If _rtl_usb_receive fails, the device is
probably not ready. Hence the error code
should be passed to the caller, so it can
react accordingly and notify the user.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel switch command for 6000 series devices
is larger than the maximum inline command size of
320 bytes. The command is therefore refused with a
warning. Fix this by allocating the command and
using the NOCOPY mechanism.

Cc: stable@kernel.org
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The driver does not count space of radiotap fields when allocating skb for
radiotap packet. This leads to kernel panic with the following call trace:

...
[67607.676067] [<c152f90f>] error_code+0x67/0x6c
[67607.676067] [<c142f831>] ? skb_put+0x91/0xa0
[67607.676067] [<f8cf5e5b>] ? ipw_handle_promiscuous_tx+0x16b/0x2d0 [ipw2200]
[67607.676067] [<f8cf5e5b>] ipw_handle_promiscuous_tx+0x16b/0x2d0 [ipw2200]
[67607.676067] [<f8cf899b>] ipw_net_hard_start_xmit+0x8b/0x90 [ipw2200]
[67607.676067] [<f8741c5a>] libipw_xmit+0x55a/0x980 [libipw]
[67607.676067] [<c143d3e8>] dev_hard_start_xmit+0x218/0x4d0
...

This bug was found by VittGam.
https://bugzilla.kernel.org/show_bug.cgi?id=43255

Cc: stable@kernel.org
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When cores are unregistered, entries
need to be removed from cores list in a safe manner.
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The problem here is that we loop until "remained_buf_len" is less than
zero, but since it is unsigned, it never is.

"remained_buf_len" has to be large enough to hold the value from
"mgmt_ie_buf_len".  That variable is type u32, but it only holds small
values so I have changed to both variables to int.

Also I removed the bogus initialization from "mgmt_ie_buf_len" so that
GCC can detect if it is used unitialized.  I moved the declaration of
"remained_buf_len" closer to where it is used so it's easier to read.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mode of WiFi dongle should be initialized in brcmf_cfg80211_up
which get called when network interface is brought up. Otherwise
brcmf_cfg80211_get_station would return error.
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Channel reported in scan results passed to cfg80211 is control
channel. But chanspec is reported while notifying cfg80211 about
roamed update. Cfg80211 complains because it could not find the
bss in the list. Report control channel while calling
cfg80211_roamed.
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

in brcmf_usb_probe_cb only return code ENOLINK was seen as an
error. This is wrong, all error codes should be returned to usb
subsystem.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the recently-added bio front_pad field to allocate struct dm_target_io.

Prior to this patch, dm_target_io was allocated from a mempool. For each
dm_target_io, there is exactly one bio allocated from a bioset.

This patch merges these two allocations into one allocation: we create a
bioset with front_pad equal to the size of dm_target_io so that every
bio allocated from the bioset has sizeof(struct dm_target_io) bytes
before it. We allocate a bio and use the bytes before the bio as
dm_target_io.

_tio_cache is removed and the tio_pool mempool is now only used for
request-based devices.

This idea was introduced by Kent Overstreet.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: tj@kernel.org
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Bill Pemberton <wfp5p@viridian.itc.virginia.edu>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The bio prison code will be useful to other future DM targets so
move it to a separate module.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The bio prison code will be useful to share with future DM targets.

Prepare to move this code into a separate module, adding a dm prefix
to structures and functions that will be exported.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Support discards when the pool's block size is not a power of 2.
The block layer assumes discard_granularity is a power of 2 (in
blkdev_issue_discard), so we set this to the largest power of 2 that is
a divides into the number of sectors in each block, but never less than
DATA_DEV_BLOCK_SIZE_MIN_SECTORS.

This patch eliminates the "Discard support must be disabled when the
block size is not a power of 2" constraint that was imposed in commit
55f2b8bd ("dm thin: support for non power of 2 pool blocksize").  That
commit was incomplete: using a block size that is not a power of 2
shouldn't mean disabling discard support on the device completely.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The device had an undocumented "feature": it can provide a sequence of
spurious link-down status data even if the link is up all the time.
A sequence of 10 was seen so update the link state only after the device
reports the same link state 20 times.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Reported-by: NMichael Leun <lkml20120218@newton.leun.net>
Tested-by: NMichael Leun <lkml20120218@newton.leun.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert cpu_to_le32(le32_to_cpu(E1) + E2) to use le32_add_cpu().

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use the ACCESS_ONCE macro in dm-bufio and dm-verity where a variable
can be modified asynchronously (through sysfs) and we want to prevent
compiler optimizations that assume that the variable hasn't changed.
(See Documentation/atomic_ops.txt.)
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use list_move() instead of list_del() + list_add().

spatch with a semantic match was used to find this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The mpio dereference should be moved below the BUG_ON NULL test
in multipath_end_io().

spatch with a semantic match was used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The commit 254d1a3f, titled
"xen/pv-on-hvm kexec: shutdown watches from old kernel" assumes that the
XenBus backend can deal with reading of values from:
 "control/platform-feature-xs_reset_watches":

    ... a patch for xenstored is required so that it
    accepts the XS_RESET_WATCHES request from a client (see changeset
    23839:42a45baf037d in xen-unstable.hg). Without the patch for xenstored
    the registration of watches will fail and some features of a PVonHVM
    guest are not available. The guest is still able to boot, but repeated
    kexec boots will fail."

Sadly this is not true when using a Xen 3.4 hypervisor and booting a PVHVM
guest. We end up hanging at:

  err = xenbus_scanf(XBT_NIL, "control",
                        "platform-feature-xs_reset_watches", "%d", &supported);

This can easily be seen with guests hanging at xenbus_init:

NX (Execute Disable) protection: active
SMBIOS 2.4 present.
DMI: Xen HVM domU, BIOS 3.4.0 05/13/2011
Hypervisor detected: Xen HVM
Xen version 3.4.
Xen Platform PCI: I/O protocol version 1
... snip ..
calling  xenbus_init+0x0/0x27e @ 1

Reverting the commit or using the attached patch fixes the issue. This fix
checks whether the hypervisor is older than 4.0 and if so does not try to
perform the read.

Fixes-Oracle-Bug: 14708233
CC: stable@vger.kernel.org
Acked-by: NOlaf Hering <olaf@aepfle.de>
[v2: Added a comment in the source code]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

It is possible to miss data when using the kdb pager.  The kdb pager
does not pay attention to the maximum column constraint of the screen
or serial terminal.  This result is not incrementing the shown lines
correctly and the pager will print more lines that fit on the screen.
Obviously that is less than useful when using a VGA console where you
cannot scroll back.

The pager will now look at the kdb_buffer string to see how many
characters are printed.  It might not be perfect considering you can
output ASCII that might move the cursor position, but it is a
substantially better approximation for viewing dmesg and trace logs.

This also means that the vt screen needs to set the kdb COLUMNS
variable.

Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

It is a common enough mistake for people to specify "kdb" when they
meant to type "kbd" that the kgdboc can just accept both since they
both mean the same thing anyway.  Specifically it is for the case
where you want kdb to be active on your graphics console + keyboard
(where kbd was the original abbreviation for keyboard).

With this change kgdboc will now accept either to mean the same thing:
   kgdboc=kbd
   kgdboc=kdb
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

The following error appeared due to a merge problem; the patches:

fc108d24 "mmc: mxs-mmc: fix deadlock caused by recursion loop"
829c1bf4 "mmc: spi: Pull out parts shared between MMC and SPI"

came in through separate branches and cause this build error when
combined.

drivers/mmc/host/mxs-mmc.c: In function 'mxs_mmc_enable_sdio_irq':
drivers/mmc/host/mxs-mmc.c:527:3: error: 'struct mxs_mmc_host' has no member named 'base'
drivers/mmc/host/mxs-mmc.c:527:3: error: 'struct mxs_mmc_host' has no member named 'devid'
make[3]: *** [drivers/mmc/host/mxs-mmc.o] Error 1

This patch corrects the issue.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some device types support a form of power management in which
the device suggests to the host that the device may be suspended
now. Support for that is best located in usbnet.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This USB V.92/V.32bis Controllered Modem have the USB vendor ID 0x0572
and device ID 0x1340. It need the NO_UNION_NORMAL quirk to be recognized.

Reference:
http://www.conexant.com/servlets/DownloadServlet/DSH-201723-005.pdf?docid=1725&revid=5
See idVendor and idProduct in table 6-1. Device Descriptors
Signed-off-by: NJean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on patch from Matthew Garrett <mjg@redhat.com> (https://lkml.org/lkml/2011/11/11/168).

http://driveragent.com/archive/30421/7-0-14 indicates that ASPM is
disabled on the 250 and 260. Duplicate for sanity.

Fixes random RX engine hangs I experienced with JMC250 on Clevo W270HU.
Signed-off-by: NKevin Baradon <kevin.baradon@gmail.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We nowdays copy the buffer and free fw->data, so make the debug printk use
the right thing.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If 'resync_max' is set to 0 (as is often done when starting a
reshape, so the mdadm can remain in control during a sensitive
period), and if the reshape request is initially delayed because
another array using the same array is resyncing or reshaping etc,
when user-space cannot easily tell when the delay changes from being
due to a conflicting reshape, to being due to resync_max = 0.

So introduce a new state: (curr_resync == 3) to reflect this, make
sure it is visible both via /proc/mdstat and via the "sync_completed"
sysfs attribute, and ensure that the event transition from one delay
state to the other is properly notified.
Signed-off-by: NNeilBrown <neilb@suse.de>