igb is ineffective at setting a lower total VFs because:

int pci_sriov_set_totalvfs(struct pci_dev *dev, u16 numvfs)
{
        ...
        /* Shouldn't change if VFs already enabled */
        if (dev->sriov->ctrl & PCI_SRIOV_CTRL_VFE)
                return -EBUSY;

Swap init ordering.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The max_vfs= option has always been self limiting to the number of VFs
supported by the device.  fa44f2f1 added SR-IOV configuration via
sysfs, but in the process broke this self correction factor.  The
failing path is:

igb_probe
  igb_sw_init
    if (max_vfs > 7) {
        adapter->vfs_allocated_count = 7;
    ...
    igb_probe_vfs
    igb_enable_sriov(, max_vfs)
      if (num_vfs > 7) {
        err = -EPERM;
        ...

This leaves vfs_allocated_count = 7 and vf_data = NULL, so we bomb out
when igb_probe finally calls igb_reset.  It seems like a really bad
idea, and somewhat pointless, to set vfs_allocated_count separate from
vf_data, but limiting max_vfs is enough to avoid the null pointer.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a problem in i350 where anti spoofing configuration was written into a
wrong register.
Signed-off-by: NLior Levy <lior.levy@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the ixgbevf driver is opened the request to allocate MSIX irq
vectors may fail.  In that case the driver will call ixgbevf_down()
which will call ixgbevf_irq_disable() to clear the HW interrupt
registers and calls synchronize_irq() using the msix_entries pointer in
the adapter structure.  However, when the function to request the MSIX
irq vectors failed it had already freed the msix_entries which causes
an OOPs from using the NULL pointer in synchronize_irq().

The calls to pci_disable_msix() and to free the msix_entries memory
should not occur if device open fails.  Instead they should be called
during device driver removal to balance with the call to
pci_enable_msix() and the call to allocate msix_entries memory
during the device probe and driver load.
Signed-off-by: NLi Xun <xunleer.li@huawei.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

fix for incorrect assignment of signed expression to unsigned variable.
Signed-off-by: NKumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF QPs must not be released when they have steering rules attached to them.

For that end, introduce a reference count field to the QP object in the
SRIOV resource tracker which is incremented/decremented when steering rules
are attached/detached to it. QPs can be released by VF only when their
ref count is zero.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the resource tracker code paths was wrongly using int and not u64
for resource tracking IDs, fix it.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the ethtool flow steering rules cleanup to be carried out before
releasing the RX QPs.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the resource tracker cleanup flow, the DMFS rules must be deleted before we
destroy the QPs, else the HW may attempt doing packet steering to non existent QPs.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the  mask is wrongly set in the MAP_EQ wrapper, fix that.
Without the fix any EQ number above 511 is mapped to one below 511.
Signed-off-by: NMoshe Lazer <moshel@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error check in cpsw_probe_dt() has an '&&' where an '||' is
meant to be. This causes a NULL pointer dereference when incomplet DT
data is passed to the driver ('phy_id' property for cpsw_emac1
missing).
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freeing netdev without free_netdev() leads to net, tx leaks.
And it may lead to dereferencing freed pointer.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ff43da86 (NET: FEC: dynamtic check DMA desc buff type) the
following build error happens when CONFIG_FEC=m

ERROR: "fec_ptp_init" [drivers/net/ethernet/freescale/fec.ko] undefined!
ERROR: "fec_ptp_ioctl" [drivers/net/ethernet/freescale/fec.ko] undefined!
ERROR: "fec_ptp_start_cyclecounter" [drivers/net/ethernet/freescale/fec.ko] undefined!

Fix it by exporting the required fec_ptp symbols.
Reported-by: NUwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following warnings that happen when building with W=1 option:

drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_free_buffers':
drivers/net/ethernet/freescale/fec.c:1337:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_alloc_buffers':
drivers/net/ethernet/freescale/fec.c:1361:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_init':
drivers/net/ethernet/freescale/fec.c:1631:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One must check the result of ioremap() -- in this case it prevents potential
kernel oops when initializing TSU registers further on...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sh_mdio_init() allocates pointer to 'struct bb_info' but only stores it locally,
so that sh_mdio_release() can't free it on driver unload.  Add the pointer to
'struct bb_info' to 'struct sh_eth_private', so that sh_mdio_init() can save
'bitbang' variable for sh_mdio_release() to be able to free it later...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

curr_cmd points to the command that is in processing or waiting
for its command response from firmware. If the function shutdown
happens to occur at this time we should cancel the cmd timer and
put the command back to free queue.

Cc: <stable@vger.kernel.org> # 3.8
Tested-by: NMarco Cesarano <marco@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During rmmod mwifiex_sdio processing FUNC_SHUTDOWN command is
sent to firmware. Firmware expcets only FUNC_INIT once WLAN
function is shut down.

Any command pending in the command queue should be ignored and
freed.

Cc: <stable@vger.kernel.org> # 3.8
Tested-by: NDaniel Drake <dsd@laptop.org>
Tested-by: NMarco Cesarano <marco@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Running the following script repeatedly on XO-4 with SD8787
produces command timeout and system lockup.

insmod mwifiex_sdio.ko
sleep 1
ifconfig eth0 up
iwlist eth0 scan &
sleep 0.5
rmmod mwifiex_sdio

mwifiex_send_cmd_async() is called for sync as well as async
commands. (mwifiex_send_cmd_sync() internally calls it for
sync command.)

"adapter->cmd_queued" gets filled inside mwifiex_send_cmd_async()
routine for both types of commands. But it is used only for sync
commands in mwifiex_wait_queue_complete(). This could lead to a
race when two threads try to queue a sync command with another
sync/async command simultaneously.

Get rid of global variable and pass command node as a parameter
to mwifiex_wait_queue_complete() to fix the problem.

Cc: <stable@vger.kernel.org> # 3.8
Reported-by: NDaniel Drake <dsd@laptop.org>
Tested-by: NDaniel Drake <dsd@laptop.org>
Tested-by: NMarco Cesarano <marco@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The beacon and multicast-buffer queues are managed by the beacon
tasklet, and the generic tx path hang check does not help in any way
here. Running it on those queues anyway can introduce some race
conditions leading to unnecessary chip resets.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit 'ath9k_hw: fix calibration issues on chainmask that don't
include chain 0' changed the hardware chainmask to the chip chainmask
for the duration of the calibration, but the revert to user
configuration in the reset path runs too early.

That causes some issues with limiting the number of antennas (including
spurious failure in hardware-generated packets).

Fix this by reverting the chainmask after the essential parts of the
calibration that need the workaround, and before NF calibration is run.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit bdb084b2
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date:   Wed Feb 13 15:49:08 2013 +0100

    iwlegacy: more checks for dma mapping errors

broke il3945_tx_skb() dma buffer length settings, what results on
firmware errors like showed below and make 3945 device non usable.

iwl3945 0000:02:00.0: Microcode SW error detected. Restarting 0x82000008.
iwl3945 0000:02:00.0: Loaded firmware version: 15.32.2.9
iwl3945 0000:02:00.0: Start IWL Error Log Dump:
iwl3945 0000:02:00.0: Status: 0x000202E4, count: 1
iwl3945 0000:02:00.0: Desc 	Time	   asrtPC blink2 ilink1  nmiPC   Line
iwl3945 0000:02:00.0: SYSASSERT     (0x5) 0000208934 0x008B6 0x0035E 0x00320 0x00000 267
iwl3945 0000:02:00.0: Error Reply type 0x00000001 cmd
Reported-by: NZdenek Kabelac <zkabelac@redhat.com>
Reported-by: NKrzysztof Kolasa <kkolasa@winsoft.pl>
Reported-by: NPedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The UPDATE_QSTAT function introduced on February 15, 2012
in commit 1355b704 "bnx2x: consistent statistics after
internal driver reload" incorrectly fails to handle overflow
during addition of the lower 32-bit field of a stat.

This bug is present since 3.4-rc1 and should thus be considered
a candidate for stable 3.4+ releases.

Google-Bug-Id: 8374428
Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Cc: Mintz Yuval <yuvalmin@broadcom.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the hardware initialization fails in bnx2x_nic_load() after adding
napi objects, they would not be deleted. A subsequent attempt to unload
the bnx2x module detects a corruption in the napi list.

Add the missing napi deletion to the error path.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix which was done in the following commit in cpsw driver has
to be taken forward to davinci emac driver as well.

commit d35162f8
Author: Daniel Mack <zonque@gmail.com>
Date:   Tue Mar 12 06:31:19 2013 +0000

    net: ethernet: cpsw: fix usage of cpdma_check_free_tx_desc()

    Commit fae50823 ("net: ethernet: davinci_cpdma: Add boundary for rx
    and tx descriptors") introduced a function to check the current
    allocation state of tx packets. The return value is taken into account
    to stop the netqork queue on the adapter in case there are no free
    slots.

    However, cpdma_check_free_tx_desc() returns 'true' if there is room in
    the bitmap, not 'false', so the usage of the function is wrong.
Reported-by: NPrabhakar Lad <prabhakar.csengg@gmail.com>
Tested-by: NPrabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The automated ARM build tests have shown that the tulip de4x5 driver
uses the old-style virt_to_bus() interface on some architectures.

Alpha, Sparc and PowerPC did not hit this problem, because they
use a different code path, and most other architectures actually
do provide VIRT_TO_BUS.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit bd329e12 ("net: cdc_ncm: do not bind to NCM compatible MBIM devices")
introduced a new policy, preferring MBIM for dual NCM/MBIM functions if
the cdc_mbim driver was enabled.  This caused a regression for users
wanting to use NCM.

Devices implementing NCM backwards compatibility according to section
3.2 of the MBIM v1.0 specification allow either NCM or MBIM on a single
USB function, using different altsettings.  The cdc_ncm and cdc_mbim
drivers will both probe such functions, and must agree on a common
policy for selecting either MBIM or NCM.  Until now, this policy has
been set at build time based on CONFIG_USB_NET_CDC_MBIM.

Use a module parameter to set the system policy at runtime, allowing the
user to prefer NCM on systems with the cdc_mbim driver.

Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Reported-by: NGeir Haatveit <nospam@haatveit.nu>
Reported-by: NTommi Kyntola <kynde@ts.ray.fi>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54791Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Kconfig file help information incorrectly mentions that the
SMSC LAN75xx config option is for SMSC LAN95xx devices.
Signed-off-by: NRobert de Vries <rhdv@xs4all.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit dc975382 introduces napi support
but never calls napi_disable. This will generate a kernel oops
(kernel BUG at include/linux/netdevice.h:473!) every time, when
ndo_stop is called followed by ndo_start.
Add the missing napi_diable call.
Signed-off-by: NGeorg Hofmann <georg@hofmannsweb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Proviously we would only restart the FEC when PHY link or duplex state
changed. PHY does not always bring down the link for speed changes, in
which case we would not detect any change and keep FEC running.

Switching link speed without restarting the FEC results in the FEC being
stuck in an indefinite state, generating error conditions for every
packet.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was failing to clear the BSSID when a disconnect happened. That
prevented a reconnection. This problem is reported at
https://bugzilla.redhat.com/show_bug.cgi?id=789605,
https://bugzilla.redhat.com/show_bug.cgi?id=866786,
https://bugzilla.redhat.com/show_bug.cgi?id=906734, and
https://bugzilla.kernel.org/show_bug.cgi?id=46171.

Thanks to Jussi Kivilinna for making the critical observation
that led to the solution.
Reported-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: NAlessandro Lannocca <alessandro.lannocca@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since v3.9-rc1 the kernel has basic support for Ralink WiSoC. The config symbols
are named slightly different than before. Fix the rt2x00 to match the new
symbols.

The commit causing this breakage is:
commit ae2b5bb6
Author: John Crispin <blogic@openwrt.org>
Date:   Sun Jan 20 22:05:30 2013 +0100
MIPS: ralink: adds Kbuild files
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit bd877e48 ("net: qmi_wwan: use a single bind function for
all device types") made Gobi 1K devices fail probing.

Using the number of endpoints in the default altsetting to decide
whether the function use one or two interfaces is wrong.  Other
altsettings may provide more endpoints.

With Gobi 1K devices, USB interface #3's altsetting is 0 by default, but
altsetting 0 only provides one interrupt endpoint and is not sufficent
for QMI.  Altsetting 1 provides all 3 endpoints required for qmi_wwan
and works with QMI. Gobi 1K layout for intf#3 is:

    Interface Descriptor:  255/255/255
      bInterfaceNumber        3
      bAlternateSetting       0
      Endpoint Descriptor:  Interrupt IN
    Interface Descriptor:  255/255/255
      bInterfaceNumber        3
      bAlternateSetting       1
      Endpoint Descriptor:  Interrupt IN
      Endpoint Descriptor:  Bulk IN
      Endpoint Descriptor:  Bulk OUT

Prior to commit bd877e48, we would call usbnet_get_endpoints
before giving up finding enough endpoints. Removing the early
endpoint number test and the strict functional descriptor
requirement allow qmi_wwan_bind to continue until
usbnet_get_endpoints has made the final attempt to collect
endpoints.  This restores the behaviour from before commit
bd877e48 without losing the added benefit of using a single bind
function.

The driver has always required a CDC Union functional descriptor
for two-interface functions. Using the existence of this
descriptor to detect two-interface functions is the logically
correct method.
Reported-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Tested-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d13ba512 ("tg3: Remove
SPEED_UNKNOWN checks") cleaned up the autoneg advertisement by
removing some dead code. One effect of this change was that the
advertisement register would not be updated if autoneg is turned off.

This exposed a bug on the 5715 device w.r.t linking. The 5715 defaults
to advertise only 10Mb Full duplex. But with autoneg disabled, it needs
the configured speed enabled in the advertisement register to link up.

This patch adds the work around to advertise all speeds on the 5715 when
autoneg is disabled.
Reported-by: NMarcin Miotk <marcinmiotk81@gmail.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bond_update_speed_duplex() might sleep while calling underlying slave's
routines. Move it out of atomic context in bond_enslave() and remove it
from bond_miimon_commit() - it was introduced by commit 546add79, however
when the slave interfaces go up/change state it's their responsibility to
fire NETDEV_UP/NETDEV_CHANGE events so that bonding can properly update
their speed.

I've tested it on all combinations of ifup/ifdown, autoneg/speed/duplex
changes, remote-controlled and local, on (not) MII-based cards. All changes
are visible.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit fae50823 ("net: ethernet: davinci_cpdma: Add boundary for rx
and tx descriptors") introduced a function to check the current
allocation state of tx packets. The return value is taken into account
to stop the netqork queue on the adapter in case there are no free
slots.

However, cpdma_check_free_tx_desc() returns 'true' if there is room in
the bitmap, not 'false', so the usage of the function is wrong.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Reported-by: NSven Neumann <s.neumann@raumfeld.com>
Reported-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Tested-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Tested-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using TX push when notifying the NIC of multiple new descriptors in
the ring will very occasionally cause the TX DMA engine to re-use an
old descriptor.  This can result in a duplicated or partly duplicated
packet (new headers with old data), or an IOMMU page fault.  This does
not happen when the pushed descriptor is the only one written.

TX push also provides little latency benefit when a packet requires
more than one descriptor.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

__netpoll_cleanup() is called in netconsole_netdev_event() while holding a
spinlock. Release/acquire the spinlock before/after it and restart the
loop. Also, disable the netconsole completely, because we won't have chance
after the restart of the loop, and might end up in a situation where
nt->enabled == 1 and nt->np.dev == NULL.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>