The SGI Altix UV2 BAU (Broadcast Assist Unit) as used for
tlb-shootdown (selective broadcast mode) always uses UV2
broadcast descriptor format. There is no need to clear the
'legacy' (UV1) mode, because the hardware always uses UV2 mode
for selective broadcast.

But the BIOS uses general broadcast and legacy mode, and the
hardware pays attention to the legacy mode bit for general
broadcast. So the kernel must not clear that mode bit.
Signed-off-by: NCliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1SccoO-0002Lh-Cb@eag09.americas.sgi.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

x86/mm: Only add extra pages count for the first memory range during pre-allocation early page table space

Robin found this regression:

| I just tried to boot an 8TB system.  It fails very early in boot with:
| Kernel panic - not syncing: Cannot find space for the kernel page tables

git bisect commit 722bc6b1.

A git revert of that commit does boot past that point on the 8TB
configuration.

That commit will add up extra pages for all memory range even
above 4g.

Try to limit that extra page count adding to first entry only.
Bisected-by: NRobin Holt <holt@sgi.com>
Tested-by: NRobin Holt <holt@sgi.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/CAE9FiQUj3wyzQxtq9yzBNc9u220p8JZ1FYHG7t%3DMOzJ%3D9BZMYA@mail.gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Some UEFI firmware will not load a .efi with a .reloc section
with a size of 0.

Therefore, we create a .efi image with 4 main areas and 3 sections.
1. PE/COFF file header
2. .setup section (covers all setup code following the first sector)
3. .reloc section (contains 1 dummy reloc entry, created in build.c)
4. .text section (covers the remaining kernel image)

To make room for the new .setup section data, the header
bugger_off_msg had to be shortened.
Reported-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1339085121-12760-1-git-send-email-jordan.l.justen@intel.comTested-by: NLee G Rosenbaum <lee.g.rosenbaum@intel.com>
Tested-by: NHenrik Rydberg <rydberg@euromail.se>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

In current Linux, percpu variable `vector_irq' is not cleared on
offlined cpus while disabling devices' irqs. If the cpu that has
the disabled irqs in vector_irq is hotplugged,
__setup_vector_irq() hits invalid irq vector and may crash.

This bug can be reproduced as following;

  # echo 0 > /sys/devices/system/cpu/cpu7/online
  # modprobe -r some_driver_using_interrupts      # vector_irq@cpu7 uncleared
  # echo 1 > /sys/devices/system/cpu/cpu7/online  # kernel may crash

This patch fixes this bug by clearing vector_irq in
__clear_irq_vector() even if the cpu is offlined.
Signed-off-by: NTomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: ltc-kernel@ml.yrl.intra.hitachi.co.jp
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/4FC340BE.7080101@hitachi.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

When rebooting our 24 CPU Westmere servers with 3.4-rc6, we
always see this warning msg:

Restarting system.
machine restart
------------[ cut here ]------------
WARNING: at arch/x86/kernel/smp.c:125
native_smp_send_reschedule+0x74/0xa7() Hardware name: X8DTN
Modules linked in: igb [last unloaded: scsi_wait_scan]
Pid: 1, comm: systemd-shutdow Not tainted 3.4.0-rc6+ #22
Call Trace:
 <IRQ>  [<ffffffff8102a41f>] warn_slowpath_common+0x7e/0x96
 [<ffffffff8102a44c>] warn_slowpath_null+0x15/0x17
 [<ffffffff81018cf7>] native_smp_send_reschedule+0x74/0xa7
 [<ffffffff810561c1>] trigger_load_balance+0x279/0x2a6
 [<ffffffff81050112>] scheduler_tick+0xe0/0xe9
 [<ffffffff81036768>] update_process_times+0x60/0x70
 [<ffffffff81062f2f>] tick_sched_timer+0x68/0x92
 [<ffffffff81046e33>] __run_hrtimer+0xb3/0x13c
 [<ffffffff81062ec7>] ? tick_nohz_handler+0xd0/0xd0
 [<ffffffff810474f2>] hrtimer_interrupt+0xdb/0x198
 [<ffffffff81019a35>] smp_apic_timer_interrupt+0x81/0x94
 [<ffffffff81655187>] apic_timer_interrupt+0x67/0x70
 <EOI>  [<ffffffff8101a3c4>] ? default_send_IPI_mask_allbutself_phys+0xb4/0xc4
 [<ffffffff8101c680>] physflat_send_IPI_allbutself+0x12/0x14
 [<ffffffff81018db4>] native_nmi_stop_other_cpus+0x8a/0xd6
 [<ffffffff810188ba>] native_machine_shutdown+0x50/0x67
 [<ffffffff81018926>] machine_shutdown+0xa/0xc
 [<ffffffff8101897e>] native_machine_restart+0x20/0x32
 [<ffffffff810189b0>] machine_restart+0xa/0xc
 [<ffffffff8103b196>] kernel_restart+0x47/0x4c
 [<ffffffff8103b2e6>] sys_reboot+0x13e/0x17c
 [<ffffffff8164e436>] ? _raw_spin_unlock_bh+0x10/0x12
 [<ffffffff810fcac9>] ? bdi_queue_work+0xcf/0xd8
 [<ffffffff810fe82f>] ? __bdi_start_writeback+0xae/0xb7
 [<ffffffff810e0d64>] ? iterate_supers+0xa3/0xb7
 [<ffffffff816547a2>] system_call_fastpath+0x16/0x1b
---[ end trace 320af5cb1cb60c5b ]---

The root cause seems to be the
default_send_IPI_mask_allbutself_phys() takes quite some time (I
measured it could be several ms) to complete sending NMIs to all
the other 23 CPUs, and for HZ=250/1000 system, the time is long
enough for a timer interrupt to happen, which will in turn
trigger to kick load balance to a stopped CPU and cause this
warning in native_smp_send_reschedule().

So disabling the local irq before stop_other_cpu() can fix this
problem (tested 25 times reboot ok), and it is fine as there
should be nobody caring the timer interrupt in such reboot
stage.

The latest 3.4 kernel slightly changes this behavior by sending
REBOOT_VECTOR first and only send NMI_VECTOR if the REBOOT_VCTOR
fails, and this patch is still needed to prevent the problem.
Signed-off-by: NFeng Tang <feng.tang@intel.com>
Acked-by: NDon Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120530231541.4c13433a@feng-i7Signed-off-by: NIngo Molnar <mingo@kernel.org>

The allmodconfig hits:

 WARNING: vmlinux.o(.text+0x6553d): Section mismatch in
          reference from the function intel_scu_devices_create() to the
          function .devinit.text: spi_register_board_info()
	  [...]

This patch marks intel_scu_devices_create() as devinit because
it only calls a devinit function, spi_register_board_info().
Signed-off-by: NSebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Link: http://lkml.kernel.org/r/20120531212025.GA8519@breakpoint.ccSigned-off-by: NIngo Molnar <mingo@kernel.org>

When hot-adding a CPU, the system outputs following messages
since node_to_cpumask_map[2] was not allocated memory.

Booting Node 2 Processor 32 APIC 0xc0
node_to_cpumask_map[2] NULL
Pid: 0, comm: swapper/32 Tainted: G       A     3.3.5-acd #21
Call Trace:
 [<ffffffff81048845>] debug_cpumask_set_cpu+0x155/0x160
 [<ffffffff8105e28a>] ? add_timer_on+0xaa/0x120
 [<ffffffff8150665f>] numa_add_cpu+0x1e/0x22
 [<ffffffff815020bb>] identify_cpu+0x1df/0x1e4
 [<ffffffff815020d6>] identify_econdary_cpu+0x16/0x1d
 [<ffffffff81504614>] smp_store_cpu_info+0x3c/0x3e
 [<ffffffff81505263>] smp_callin+0x139/0x1be
 [<ffffffff815052fb>] start_secondary+0x13/0xeb

The reason is that the bit of node 2 was not set at
numa_nodes_parsed. numa_nodes_parsed is set by only
acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init. Thus even if hot-added memory
which is same PXM as hot-added CPU is written in ACPI SRAT
Table, if the hot-added CPU is not written in ACPI SRAT table,
numa_nodes_parsed is not set.

But according to ACPI Spec Rev 5.0, it says about ACPI SRAT
table as follows: This optional table provides information that
allows OSPM to associate processors and memory ranges, including
ranges of memory provided by hot-added memory devices, with
system localities / proximity domains and clock domains.

It means that ACPI SRAT table only provides information for CPUs
present at boot time and for memory including hot-added memory.
So hot-added memory is written in ACPI SRAT table, but hot-added
CPU is not written in it. Thus numa_nodes_parsed should be set
by not only acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init but also
acpi_numa_memory_affinity_init for the case.

Additionally, if system has cpuless memory node,
acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init cannot set numa_nodes_parseds
since these functions cannot find cpu description for the node.
In this case, numa_nodes_parsed needs to be set by
acpi_numa_memory_affinity_init.
Signed-off-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: liuj97@gmail.com
Cc: kosaki.motohiro@gmail.com
Link: http://lkml.kernel.org/r/4FCC2098.4030007@jp.fujitsu.com
[ merged it ]
Signed-off-by: NIngo Molnar <mingo@kernel.org>

aperture_64.c now is using memblock, the previous
kmemleak_ignore() for alloc_bootmem() should be removed then.

Otherwise, with kmemleak enabled, kernel will throw warnings
like:

[    0.000000] kmemleak: Trying to color unknown object at 0xffff8800c4000000 as Black
[    0.000000] Pid: 0, comm: swapper/0 Not tainted 3.5.0-rc1-next-20120605+ #130
[    0.000000] Call Trace:
[    0.000000]  [<ffffffff811b27e6>] paint_ptr+0x66/0xc0
[    0.000000]  [<ffffffff816b90fb>] kmemleak_ignore+0x2b/0x60
[    0.000000]  [<ffffffff81ef7bc0>] kmemleak_init+0x217/0x2c1
[    0.000000]  [<ffffffff81ed2b97>] start_kernel+0x32d/0x3eb
[    0.000000]  [<ffffffff81ed25e4>] ? repair_env_string+0x5a/0x5a
[    0.000000]  [<ffffffff81ed2356>] x86_64_start_reservations+0x131/0x135
[    0.000000]  [<ffffffff81ed2120>] ? early_idt_handlers+0x120/0x120
[    0.000000]  [<ffffffff81ed245c>] x86_64_start_kernel+0x102/0x111
[    0.000000] kmemleak: Early log backtrace:
[    0.000000]    [<ffffffff816b911b>] kmemleak_ignore+0x4b/0x60
[    0.000000]    [<ffffffff81ee6a38>] gart_iommu_hole_init+0x3e7/0x547
[    0.000000]    [<ffffffff81edb20b>] pci_iommu_alloc+0x44/0x6f
[    0.000000]    [<ffffffff81ee81ad>] mem_init+0x19/0xec
[    0.000000]    [<ffffffff81ed2a54>] start_kernel+0x1ea/0x3eb
[    0.000000]    [<ffffffff81ed2356>] x86_64_start_reservations+0x131/0x135
[    0.000000]    [<ffffffff81ed245c>] x86_64_start_kernel+0x102/0x111
[    0.000000]    [<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: NXiaotian Feng <dannyfeng@tencent.com>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1338922831-2847-1-git-send-email-xtfeng@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

commit 82f7af09 ("x86/mce: Cleanup timer mess) dropped the
initialization of the per cpu timer interval. Duh :(

Restore the previous behaviour.
Reported-by: NChen Gong <gong.chen@linux.intel.com>
Cc: bp@amd64.org
Cc: tony.luck@intel.com
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

In commit 82f7af09 ("x86/mce: Cleanup timer mess), Thomas just
forgot the "/ 2" there while cleaning up.
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: bp@amd64.org
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1338863702-9245-1-git-send-email-gong.chen@linux.intel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Pull fuse updates from Miklos Szeredi.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix blksize calculation
  fuse: fix stat call on 32 bit platforms
  fuse: optimize fallocate on permanent failure
  fuse: add FALLOCATE operation
  fuse: Convert to kstrtoul_from_user

Pull scheduler fixes from Ingo Molnar.

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Remove NULL assignment of dattr_cur
  sched: Remove the last NULL entry from sched_feat_names
  sched: Make sched_feat_names const
  sched/rt: Fix SCHED_RR across cgroups
  sched: Move nr_cpus_allowed out of 'struct sched_rt_entity'
  sched: Make sure to not re-read variables after validation
  sched: Fix SD_OVERLAP
  sched: Don't try allocating memory from offline nodes
  sched/nohz: Fix rq->cpu_load calculations some more
  sched/x86: Use cpu_llc_shared_mask(cpu) for coregroup_mask

Pull signal and vfs compile breakage fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  fixups for signal breakage

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  nommu: fix compilation of nommu.c

Pull cifs fixes from Steve French.

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Move get_next_mid to ops struct
  CIFS: Make accessing is_valid_oplock/dump_detail ops struct field safe
  CIFS: Improve identation in cifs_unlock_range
  CIFS: Fix possible wrong memory allocation

Obvious brainos spotted by Geert.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Compiling 3.5-rc1 for nommu targets gives:

  CC      mm/nommu.o
mm/nommu.c: In function ‘sys_mmap_pgoff’:
mm/nommu.c:1489:2: error: ‘ret’ undeclared (first use in this function)
mm/nommu.c:1489:2: note: each undeclared identifier is reported only once for each function it appears in

It is trivially fixed by replacing 'ret' with the local variable that is
already defined for the return value 'retval'.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Pull frontswap feature from Konrad Rzeszutek Wilk:
 "Frontswap provides a "transcendent memory" interface for swap pages.
  In some environments, dramatic performance savings may be obtained
  because swapped pages are saved in RAM (or a RAM-like device) instead
  of a swap disk.  This tag provides the basic infrastructure along with
  some changes to the existing backends."

Fix up trivial conflict in mm/Makefile due to removal of swap token code
changing a line next to the new frontswap entry.

This pull request came in before the merge window even opened, it got
delayed to after the merge window by me just wanting to make sure it had
actual users.  Apparently IBM is using this on their embedded side, and
Jan Beulich says that it's already made available for SLES and OpenSUSE
users.

Also acked by Rik van Riel, and Konrad points to other people liking it
too.  So in it goes.

By Dan Magenheimer (4) and Konrad Rzeszutek Wilk (2)
via Konrad Rzeszutek Wilk
* tag 'stable/frontswap.v16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm:
  frontswap: s/put_page/store/g s/get_page/load
  MAINTAINER: Add myself for the frontswap API
  mm: frontswap: config and doc files
  mm: frontswap: core frontswap functionality
  mm: frontswap: core swap subsystem hooks and headers
  mm: frontswap: add frontswap header file

Merge branches 'irq-urgent-for-linus' and 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq and smpboot updates from Thomas Gleixner:
 "Just cleanup patches with no functional change and a fix for suspend
  issues."

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Introduce irq_do_set_affinity() to reduce duplicated code
  genirq: Add IRQS_PENDING for nested and simple irq

* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smpboot, idle: Fix comment mismatch over idle_threads_init()
  smpboot, idle: Optimize calls to smp_processor_id() in idle_threads_init()

Pull timer updates from Thomas Gleixner:
 "The clocksource driver is pure hardware enablement and the skew option
  is default off, well tested and non dangerous."

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick: Move skew_tick option into the HIGH_RES_TIMER section
  clocksource: em_sti: Add DT support
  clocksource: em_sti: Emma Mobile STI driver
  clockevents: Make clockevents_config() a global symbol
  tick: Add tick skew boot option

Cyrill Gorcunov reports that I broke the fdinfo files with commit
30a08bf2 ("proc: move fd symlink i_mode calculations into
tid_fd_revalidate()"), and he's quite right.

The tid_fd_revalidate() function is not just used for the <tid>/fd
symlinks, it's also used for the <tid>/fdinfo/<fd> files, and the
permission model for those are different.

So do the dynamic symlink permission handling just for symlinks, making
the fdinfo files once more appear as the proper regular files they are.

Of course, Al Viro argued (probably correctly) that we shouldn't do the
symlink permission games at all, and make the symlinks always just be
the normal 'lrwxrwxrwx'.  That would have avoided this issue too, but
since somebody noticed that the permissions had changed (which was the
reason for that original commit 30a08bf2 in the first place), people
do apparently use this feature.

[ Basically, you can use the symlink permission data as a cheap "fdinfo"
  replacement, since you see whether the file is open for reading and/or
  writing by just looking at st_mode of the symlink.  So the feature
  does make sense, even if the pain it has caused means we probably
  shouldn't have done it to begin with. ]
Reported-and-tested-by: NCyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Should be 'exynos5_xxx' instead of 'exonys5_xxx'.

It happened at the commit 30b84288 ("Merge tag 'soc2' of
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc")
during v3.5 merge window.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
[ My bad  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull some left-over PM patches from Rafael J. Wysocki.

* 'pm-acpi' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Make acpi_pm_device_sleep_state() follow the specification
  ACPI / PM: Make __acpi_bus_get_power() cover D3cold correctly
  ACPI / PM: Fix error messages in drivers/acpi/bus.c
  rtc-cmos / PM: report wakeup event on ACPI RTC alarm
  ACPI / PM: Generate wakeup events on fixed power button

This reverts commit 5ceb9ce6.

That commit seems to be the cause of the mm compation list corruption
issues that Dave Jones reported.  The locking (or rather, absense
there-of) is dubious, as is the use of the 'page' variable once it has
been found to be outside the pageblock range.

So revert it for now, we can re-visit this for 3.6.  If we even need to:
as Minchan Kim says, "The patch wasn't a bug fix and even test workload
was very theoretical".
Reported-and-tested-by: NDave Jones <davej@redhat.com>
Acked-by: NHugh Dickins <hughd@google.com>
Acked-by: NKOSAKI Motohiro <kosaki.motohiro@gmail.com>
Acked-by: NMinchan Kim <minchan@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

New tmpfs use of !PageUptodate pages for fallocate() is triggering the
WARNING: at mm/page-writeback.c:1990 when __set_page_dirty_nobuffers()
is called from migrate_page_copy() for compaction.

It is anomalous that migration should use __set_page_dirty_nobuffers()
on an address_space that does not participate in dirty and writeback
accounting; and this has also been observed to insert surprising dirty
tags into a tmpfs radix_tree, despite tmpfs not using tags at all.

We should probably give migrate_page_copy() a better way to preserve the
tag and migrate accounting info, when mapping_cap_account_dirty().  But
that needs some more work: so in the interim, avoid the warning by using
a simple SetPageDirty on PageSwapBacked pages.
Reported-and-tested-by: NDave Jones <davej@redhat.com>
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The comment above it says "Stat data, not accessed from path walking",
but in fact some of inode fields we use for the common stat data was way
down at the end of the inode, causing unnecessary cache misses for the
common stat operations.

The inode structure is pretty big, and this can change padding depending
on field width, but at least on the common 64-bit configurations this
doesn't change the size.  Some of our inode layout has historically been
to tro to avoid unnecessary padding fields, but cache locality is at
least as important for layout, if not more.

Noticed by looking at kernel profiles, and noticing that the "i_blkbits"
access stood out like a sore thumb.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull device-mapper updates from Alasdair G Kergon:
 "Improve multipath's retrying mechanism in some defined circumstances
  and provide a simple reserve/release mechanism for userspace tools to
  access thin provisioning metadata while the pool is in use."

* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm thin: provide userspace access to pool metadata
  dm thin: use slab mempools
  dm mpath: allow ioctls to trigger pg init
  dm mpath: delay retry of bypassed pg
  dm mpath: reduce size of struct multipath

This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_.  This,
read-only snapshot can be accessed by userland, concurrently with the
live target.

Only one metadata snapshot can be held at a time.  The pool's status
line will give the block location for the current msnap.

Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:

    thin_dump -m <msnap root> <metadata dev>

Available here: https://github.com/jthornber/thin-provisioning-tools

Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:

     i) Incremental backups.

     By using metadata snapshots we can work out what blocks have
     changed over time.  Combined with data snapshots we can ensure
     the data doesn't change while we back it up.

     A short proof of concept script can be found here:

     https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb

     ii) Migration of thin devices from one pool to another.

     iii) Merging snapshots back into an external origin.

     iv) Asyncronous replication.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device.  Until this has happened, ioctls return -EAGAIN.

With this patch, new paths are made available in response to an ioctl
too.  The processing of the ioctl gets delayed until this has happened.

Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.

Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure.  Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands).  For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too.  It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.

If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes.  Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes).  This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Pull networking updates from David Miller:

 1) Make syn floods consume significantly less resources by

    a) Not pre-COW'ing routing metrics for SYN/ACKs
    b) Mirroring the device queue mapping of the SYN for the SYN/ACK
       reply.

    Both from Eric Dumazet.

 2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.

 3) Validate the length requested when building a paged SKB for a
    socket, so we don't overrun the page vector accidently.  From Jason
    Wang.

 4) When netlabel is disabled, we abort all IP option processing when we
    see a CIPSO option.  This isn't the right thing to do, we should
    simply skip over it and continue processing the remaining options
    (if any).  Fix from Paul Moore.

 5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
    Apfelbaum.

 6) 8139cp enables the receiver before the ring address is properly
    programmed, which potentially lets the device crap over random
    memory.  Fix from Jason Wang.

 7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
    address reference in jumbo RX frame processing from Bruce Allan and
    Sebastian Andrzej Siewior, respectively.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  fec_mpc52xx: fix timestamp filtering
  mcs7830: Implement link state detection
  e1000e: fix Rapid Start Technology support for i217
  e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
  r8169: call netif_napi_del at errpaths and at driver unload
  tcp: reflect SYN queue_mapping into SYNACK packets
  tcp: do not create inetpeer on SYNACK message
  8139cp/8139too: terminate the eeprom access with the right opmode
  8139cp: set ring address before enabling receiver
  cipso: handle CIPSO options correctly when NetLabel is disabled
  net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
  bql: Avoid possible inconsistent calculation.
  bql: Avoid unneeded limit decrement.
  bql: Fix POSDIFF() to integer overflow aware.
  net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
  net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
  net/mlx4_core: Fixes for VF / Guest startup flow
  net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
  net/mlx4_core: Fix number of EQs used in ICM initialisation
  net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int

Pull straggler x86 fixes from Peter Anvin:
 "Three groups of patches:

  - EFI boot stub documentation and the ability to print error messages;
  - Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
    should never have been ported, and the port is broken and
    potentially dangerous.)
  - ftrace stack corruption fixes.  I'm not super-happy about the
    technical implementation, but it is probably the least invasive in
    the short term.  In the future I would like a single method for
    nesting the debug stack, however."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
  x86, efi: Add EFI boot stub documentation
  x86, efi; Add EFI boot stub console support
  x86, efi: Only close open files in error path
  ftrace/x86: Do not change stacks in DEBUG when calling lockdep
  x86: Allow nesting of the debug stack IDT setting
  x86: Reset the debug_stack update counter
  ftrace: Use breakpoint method to update ftrace caller
  ftrace: Synchronize variable setting with breakpoints

This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.

The main revert is d29f3ef3 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:

  fde86d31 - tty: add lockdep annotations
  8f6576ad - tty: fix ldisc lock inversion trace
  d3ca8b64 - pty: Fix lock inversion
  b1d679af - tty: drop the pty lock during hangup
  abcefe5f - tty/amiserial: Add missing argument for tty_unlock()
  fd11b42e - cris: fix missing tty arg in wait_event_interruptible_tty call
  d29f3ef3 - tty_lock: Localise the lock

The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: NStephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull vfs fix and a fix from the signal changes for frv from Al Viro.

The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short".  Al didn't notice, and
made both of them be the unsigned short.

The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  powerpc: Fix size of st_nlink on 64bit

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  frv: Remove bogus closing parenthesis

commit e57f93cc (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Introduced by commit 6fd84c08
("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set")
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>